The POSTING_READ() calls were originally added to make sure the writes
were flushed before any timing delays and across loops.
Now that the code has settled a bit, let's remove them.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Save the GMBUS2 value read while polling for state changes, and then
reuse this value when determining for which reason the loops were exited.
This is a small optimization which saves a couple of bus accesses for
memory mapped IO registers.
To avoid "assigning in if clause" checkpatch errors", use a ret variable
to store the wait_for macro return value.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is very common for an i2c device to require a small 1 or 2 byte write
followed by a read. For example, when reading from an i2c EEPROM it is
common to write and address, offset or index followed by a reading some
values.
The i915 gmbus controller provides a special "INDEX" cycle for performing
such a small write followed by a read. The INDEX can be either one or two
bytes long. The advantage of using such a cycle is that the CPU has
slightly less work to do once the read with INDEX cycle is started.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915 is only able to generate a STOP cycle (i.e. finalize an i2c
transaction) during a DATA or WAIT phase. In other words, the
controller rejects a STOP requested as part of the first transaction in a
sequence.
Thus, for the first transaction we must always use a WAIT cycle, detect
when the device has finished (and is in a WAIT phase), and then either
start the next transaction, or, if there are no more transactions,
generate a STOP cycle.
Note: Theoretically, the last transaction of a multi-transaction sequence
could initiate a STOP cycle. However, this slight optimization is left
for another patch. We return -ETIMEDOUT if the hardware doesn't
deactivate after the STOP cycle.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
[danvet: added comment to the code that gmbus can't generate STOP on
the very first cycle.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GMBUS controller can report a NAK condition while a transaction is
still active. If the driver is fast enough, and the bus is slow enough,
the driver may clear the NAK condition while the controller is still
busy, resulting in a confused GMBUS controller. This will leave the
controller in a bad state such that the next transaction may fail.
Also, return -ENXIO if a device NAKs a transaction.
Note: this patch also refactors gmbus_xfer to remove the "done" label.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GMBUS controller GMBUS3 register is double-buffered. Take advantage
of this by writing two 4-byte words before the first wait for HW_RDY.
This helps keep the GMBUS controller from becoming idle during long writes.
In fact, during experiments using the GMBUS interrupts, the HW_RDY
interrupt would only trigger for transactions >4 bytes after 2 writes
to GMBUS3.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A common method of probing an i2c bus is trying to do a zero-length write.
Handle this case by checking the length first before decrementing it.
This is actually important, since attempting a zero-length write is one
of the ways that i2cdetect and i2c_new_probed_device detect whether
there is device present on the bus with a given address.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory this will have performance and power improvements. Performance
because we don't need to stall when the scanout BO is busy, and power
because we don't have to stall when the BO is busy (and the ring can
even go to sleep if the HW supports it).
v2:
squash 2 patches into 1 (me)
un-inline the enable_semaphores function (Daniel)
remove comment about SNB hangs from i915_gem_object_sync (Chris)
rename intel_enable_semaphores to i915_semaphore_is_enabled (me)
removed page flip comment; "no why" (Chris)
To address other comments from Daniel (irc):
update the comment to say 'vt-d is crap, don't enable semaphores'
- I think you misinterpreted Chris' comment, it already exists.
checking out whether we can pageflip on the render ring on ivb (didn't
work on early silicon)
- We don't want to enable workarounds for early silicon unless we have
to.
- I can't find any references in the docs about this.
optionally use it if the fb is already busy on the render ring
- This should be how the code already worked, unless I am
misunderstanding your meaning.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By simplifying the rules to calling get_fence when writing to the
through the GTT in a tiled manner, and calling put_fence before writing
to the object through the GTT in a linear manner, the code becomes
clearer and there is less chance of making a mistake.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: fixed up conflict with ppgtt code and spelling in a new
comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RC6 residency should be in intervals of 1.28us, and the counter wraps.
Here is an example using awk to get the various RC6 and RC6+ residency
times in seconds, since boot.
cat /sys/kernel/debug/dri/0/i915_drpc_info | grep residency | awk -F':' -F' ' '{print $5 * 1.28 / 1000000}'
This is primarily for QA, but has other applications as well. An
upcoming patch to add interfaces should be more interesting to
application developers.
v2: move comment to the correct place
v3: display with %u instead of %d, for Ouping
CC: Ouping Zhang <ouping.zhang@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: fixed exynos broken ioctl
drm/exynos: fix to pointer manager member of struct exynos_drm_subdrv
drm/exynos: fix struct for operation callback functions to driver name
drm/exynos: use define instead of default_win member in struct mixer_context
drm/exynos: rename s/HDMI_OVERLAY_NUMBER/MIXER_WIN_NR
drm/exynos: remove unused codes in hdmi and mixer
drm/exynos: remove unnecessary type conversion of hdmi and mixer
drm/exynos: add format list of plane
drm/exynos: fixed duplicated page allocation bug.
drm/exynos: fixed page align and code clean.
Daniel Vetter writes:
3 regression fixes:
- disable gmbus again, too broken for 3.4, we'll try again for 3.5
- dp bandwidth computation fix, we've lost the 6bpc dithering flag
sometimes, this is a 3.3 regression (maybe even earlier for some
configurations).
- fix resume regression caused by the gen2/3 fencing fix merged into -rc2.
And a few other fixes:
- gpu hang fix for i845 (Chris)
- sprite fix (Armin Reese)
- crtc disable vs. scanlinewait race fix (Chris)
- rc6 module option read-only, it confused testers (Jesse)
- fbc related blitter death hw workaround, note that we disable fbc on snb
by default anyway.
With these fixes we have one 3.4 regression outstanding: One of the
cleanup patches for the interlaced support managed to confuse the lvds
panel fitter when upscaling. The root-cause is still unclear, but test
patches are awaiting feedback from the reporter.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: clear fencing tracking state when retiring requests
drm/i915: make rc6 module parameter read-only
drm/i915: implement ColorBlt w/a
drm/i915/ringbuffer: Exclude last 2 cachlines of ring on 845g
Revert "drm/i915: reenable gmbus on gen3+ again"
drm/i915: properly compute dp dithering for user-created modes
drm/i915: Finish any pending operations on the framebuffer before disabling
drm/i915: Removed IVB forced enable of sprite dest key.
Daniel Vetter wrote
First pull request for 3.5-next, slightly large than usual because new
things kept coming in since the last pull for 3.4.
Highlights:
- first batch of hw enablement for vlv (Jesse et al) and hsw (Eugeni). pci
ids are not yet added, and there's still quite a few patches to merge
(mostly modesetting). To make QA easier I've decided to merge this stuff
in pieces.
- loads of cleanups and prep patches spurred by the above. Especially vlv
is a real frankenstein chip, but also hsw is stretching our driver's
code design. Expect more to come in this area for 3.5.
- more gmbus fixes, cleanups and improvements by Daniel Kurtz. Again,
there are more patches needed (and some already queued up), but I wanted
to split this a bit for better testing.
- pwrite/pread rework and retuning. This series has been in the works for
a few months already and a lot of i-g-t tests have been created for it.
Now it's finally ready to be merged. Note that one patch in this series
touches include/pagemap.h, that patch is acked-by akpm.
- reduce mappable pressure and relocation throughput improvements from
Chris.
- mmap offset exhaustion mitigation by Chris Wilson.
- a start at figuring out which codepaths in our messy dri1/ums+gem/kms
driver we actually need to support by bailing out of unsupported case.
The driver now refuses to load without kms on gen6+ and disallows a few
ioctls that userspace never used in certain cases. More of this will
definitely come.
- More decoupling of global gtt and ppgtt.
- Improved dual-link lvds detection by Takashi Iwai.
- Shut up the compiler + plus fix the fallout (Ben)
- Inverted panel brightness handling (mostly Acer manages to break things
in this way).
- Small fixlets and adjustements and some minor things to help debugging.
Regression-wise QA reported quite a few issues on ivb, but all of them
turned out to be hw stability issues which are already fixed in
drm-intel-fixes (QA runs the nightly regression tests on -next alone,
without -fixes automatically merged in). There's still one issue open on
snb, it looks like occlusion query writes are not quite as cache coherent
as we've expected. With some of the pwrite adjustements we can now
reliably hit this. Kernel workaround for it is in the works."
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
drm/i915: VCS is not the last ring
drm/i915: Add a dual link lvds quirk for MacBook Pro 8,2
drm/i915: make quirks more verbose
drm/i915: dump the DMA fetch addr register on pre-gen6
drm/i915/sdvo: Include YRPB as an additional TV output type
drm/i915: disallow gem init ioctl on ilk
drm/i915: refuse to load on gen6+ without kms
drm/i915: extract gt interrupt handler
drm/i915: use render gen to switch ring irq functions
drm/i915: rip out old HWSTAM missed irq WA for vlv
drm/i915: open code gen6+ ring irqs
drm/i915: ring irq cleanups
drm/i915: add SFUSE_STRAP registers for digital port detection
drm/i915: add WM_LINETIME registers
drm/i915: add WRPLL clocks
drm/i915: add LCPLL control registers
drm/i915: add SSC offsets for SBI access
drm/i915: add port clock selection support for HSW
drm/i915: add S PLL control
drm/i915: add PIXCLK_GATE register
...
Conflicts:
drivers/char/agp/intel-agp.h
drivers/char/agp/intel-gtt.c
drivers/gpu/drm/i915/i915_debugfs.c
On coherent systems (not-AGP) the IB should be in cached memory so should
be just as fast, so we can avoid copying to temporary pages and just use it
directly.
provides minor speedups on rv530: gears ~1820->1860, ipers: 29.9->30.6,
but always good to use less CPU if we can.
v3: cleanup unneeded bits.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This closes a race seen with kexec where we enable PCI bus mastering
but the card has been reinitialised fully yet.
This was previously fixed by a patch from Jerome, but this should
close the race completely.
v2: add SI support as suggested by Alex.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a resume regression introduced in
commit 7dd4906586
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Mar 21 10:48:18 2012 +0000
drm/i915: Mark untiled BLT commands as fenced on gen2/3
which fixed fencing tracking for untiled blt commands.
A side effect of that patch was that now also untiled objects have a
non-zero obj->last_fenced_seqno to track when a fence can be set up
after a pipelined tiling change. Unfortunately this was only cleared
by the fence setup and teardown code, resulting in tons of untiled but
inactive objects with non-zero last_fenced_seqno.
Now after resume we completely reset the seqno tracking, both on the
driver side (by setting dev_priv->next_seqno = 1) and on the hw side
(by allocating a new hws page, which contains the seqnos). Hilarity
and indefinite waits ensued from the stale seqnos in
obj->last_fenced_seqno from before the suspend.
The fix is to properly clear the fencing tracking state like we
already do for the normal gpu rendering while moving objects off the
active list.
Reported-and-tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The struct exynos_drm_manager has to exist for exynos drm sub driver
using encoder and connector. If it isn't NULL to member of struct
exynos_drm_subdrv, will create encoder and connector else will not. And
the is_local member also doesn't need.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The mixer driver and hdmi driver have each operation callback functions
and they is registered to hdmi common driver. Their struct names in hdmi
common driver include display, manager and overlay. It confuses to
appear whose operation and two driver cannot register same operation
callback functions at the same time. Use their struct names to driver
name.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The default_win member in struct mixer_context isn't change its value
after initialized to 0, so it's better using to define.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI_OVERLAY_NUMBER is specific of mixer driver and be used "windows
layer" term in exynos user manaual, so rename it.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some members in struct mixer_context aren't used and the define
HDMI_OVERLAY_NUMBER is unused in hdmi driver, remove them.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When the void pointer type variable is assigned to the specific pointer
type variable, don't need to do type conversion.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
According to an internal workaround master list, we need to set bit 5
of register 9400 to avoid issues with color blits.
Testing shows that this seems to fix the blitter hangs when fbc is
enabled on snb, thanks to Chris Wilson for figuring this out.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Michael "brot" Groh <michael.groh@minad.de>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
