It has been observed that in zero-loss benchmarks, when a
slow traffic rate is being tested, the IRQ timer coalescing
parameter was set too high, and the ethernet controller
would start dropping packets because the job ring back half
wouldn't be executed in time before the ethernet controller
would fill its buffers, thereby significantly reducing the
zero-loss performance figures.
Empirical testing has shown that the best zero-loss performance
is achieved when IRQ coalescing is set to minimum values and/or
turned off, since apparently the job ring driver already implements
an adequately-performing general-purpose IRQ mitigation strategy
in software.
Whilst we could go with minimal count (2-8) and timing settings
(192-256), we prefer just turning h/w coalescing altogether off
to minimize setkey latency (due to split key generation), and
for consistent cross-SoC performance (the SEC vs. core clock
ratio changes).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC v4.x' RNGB h/w block self-initialized. RNG4, available
on SEC versions 5 and beyond, is based on a different standard
that requires manual initialization.
Also update any new errors From the SEC v5.2 reference manual:
The SEC v5.2's RNG4 unit reuses some error IDs, thus the addition
of rng_err_id_list over the CHA-independent err_id_list.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC v4.x were only 36-bit, SEC v5+ are 40-bit capable.
Also set a DMA mask for any job ring devices created.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam_read copies random bytes from two buffers into output.
caam rng can fill empty buffer 0xffff bytes at a time,
but the buffer sizes are rounded down to multiple of cacheline size.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- rename scatterlist and link_tbl functions
- link_tbl changed to sec4_sg
- sg_to_link_tbl_one changed to dma_to_sec4_sg_one,
since no scatterlist is use
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
functions for external storage of seq in/out lengths,
i.e., for 32-bit lengths.
These type-dependent functions automatically determine whether to
store the length internally (embedded in the command header word) or
externally (after the address pointer), based on size of the type
given.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
init_desc, by always ORing with 1 for the descriptor header inclusion
into the descriptor length, and init_sh_desc_pdb, by always specifying
the descriptor length modification for the PDB via options, would not
allow for odd length PDBs to be embedded in the constructed descriptor
length. Fix this by simply changing the OR to an addition.
also round-up pdb_bytes to the next SEC command unit size, to
allow for, e.g., optional packet header bytes that aren't a
multiple of CAAM_CMD_SZ.
Reported-by: Radu-Andrei BULIE <radu.bulie@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Yashpal Dutta <yashpal.dutta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case of protocol acceleration descriptors, Shared descriptor header must
carry size of header length + PDB length in words which will be skipped by
DECO while processing descriptor to provide first command word offset
Signed-off-by: Yashpal Dutta <yashpal.dutta@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC4 h/w gets configured in 32- vs. 36-bit physical
addressing modes depending on the size of dma_addr_t,
which is not always equal to sizeof(u32 *).
Also fixed alignment of a dma_unmap call whilst in there.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the nx driver was pulled, the Makefile that actually
builds it is arch/powerpc/Makefile. This is unnatural.
This patch moves the line that builds the nx driver from
arch/powerpc/Makefile to drivers/crypto/Makefile where it
belongs.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since mv_hash_final_fallback() uses ctx->state, read out the digest
state register before calling it.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The timer triggers when 500ms have gone by after triggering the engine
and no completion interrupt was received. The callback then tries to
sanitise things as well as possible.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CRC peripheral is a hardware block used to compute the CRC of the block
of data. This is based on a CRC32 engine which computes the CRC value of 32b
data words presented to it. For data words of < 32b in size, this driver
pack 0 automatically into 32b data units. This driver implements the async
hash crypto framework API.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Pull crypto updates from Herbert Xu:
- New cipher/hash driver for ARM ux500.
- Code clean-up for aesni-intel.
- Misc fixes.
Fixed up conflicts in arch/arm/mach-ux500/devices-common.h, where quite
frankly some of it made no sense at all (the pull brought in a
declaration for the dbx500_add_platform_device_noirq() function, which
neither exists nor is used anywhere).
Also some trivial add-add context conflicts in the Kconfig file in
drivers/{char/hw_random,crypto}/
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni-intel - move more common code to ablk_init_common
crypto: aesni-intel - use crypto_[un]register_algs
crypto: ux500 - Cleanup hardware identification
crypto: ux500 - Update DMA handling for 3.4
mach-ux500: crypto - core support for CRYP/HASH module.
crypto: ux500 - Add driver for HASH hardware
crypto: ux500 - Add driver for CRYP hardware
hwrng: Kconfig - modify default state for atmel-rng driver
hwrng: omap - use devm_request_and_ioremap
crypto: crypto4xx - move up err_request_irq label
crypto, xor: Sanitize checksumming function selection output
crypto: caam - add backward compatible string sec4.0
Pull powerpc updates from Benjamin Herrenschmidt:
"Here are the powerpc goodies for 3.5. Main highlights are:
- Support for the NX crypto engine in Power7+
- A bunch of Anton goodness, including some micro optimization of our
syscall entry on Power7
- I converted a pile of our thermal control drivers to the new i2c
APIs (essentially turning the old therm_pm72 into a proper set of
windfarm drivers). That's one more step toward removing the
deprecated i2c APIs, there's still a few drivers to fix, but we are
getting close
- kexec/kdump support for 47x embedded cores
The big missing thing here is no updates from Freescale. Not sure
what's up here, but with Kumar not working for them anymore things are
a bit in a state of flux in that area."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc: Fix irq distribution
Revert "powerpc/hw-breakpoint: Use generic hw-breakpoint interfaces for new PPC ptrace flags"
powerpc: Fixing a cputhread code documentation
powerpc/crypto: Enable the PFO-based encryption device
powerpc/crypto: Build files for the nx device driver
powerpc/crypto: debugfs routines and docs for the nx device driver
powerpc/crypto: SHA512 hash routines for nx encryption
powerpc/crypto: SHA256 hash routines for nx encryption
powerpc/crypto: AES-XCBC mode routines for nx encryption
powerpc/crypto: AES-GCM mode routines for nx encryption
powerpc/crypto: AES-ECB mode routines for nx encryption
powerpc/crypto: AES-CTR mode routines for nx encryption
powerpc/crypto: AES-CCM mode routines for nx encryption
powerpc/crypto: AES-CBC mode routines for nx encryption
powerpc/crypto: nx driver code supporting nx encryption
powerpc/pseries: Enable the PFO-based RNG accelerator
powerpc/pseries/hwrng: PFO-based hwrng driver
powerpc/pseries: Add PFO support to the VIO bus
powerpc/pseries: Add pseries update notifier for OFDT prop changes
powerpc/pseries: Add new hvcall constants to support PFO
...
