There is a small race window in the __switch_to code in regard to
the transfer of the TIF_MCCK_PENDING bit from the previous to the
next task. The bit is transferred before the task struct pointer
and the thread-info pointer for the next task has been stored to
lowcore. If a machine check sets the TIF_MCCK_PENDING bit between
the transfer code and the store of current/thread_info the bit
is still set for the previous task. And if the previous task has
terminated it can get lost. The effect is that a pending CRW is
not retrieved until the next machine checks sets TIF_MCCK_PENDING.
To fix this reorder __switch_to to first store the task struct
and thread-info pointer and then do the transfer of the bit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Whenever the cpu loads an enabled wait PSW it will appear as idle to the
underlying host system. The code in default_idle calls vtime_stop_cpu
which does the necessary voodoo to get the cpu time accounting right.
The udelay code just loads an enabled wait PSW. To correct this rework
the vtime_stop_cpu/vtime_start_cpu logic and move the difficult parts
to entry[64].S, vtime_stop_cpu can now be called from anywhere and
vtime_start_cpu is gone. The correction of the cpu time during wakeup
from an enabled wait PSW is done with a critical section in entry[64].S.
As vtime_start_cpu is gone, s390_idle_check can be removed as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define struct pcpu and merge some of the NR_CPUS arrays into it, including
__cpu_logical_map, current_set and smp_cpu_state. Split smp related
functions to those operating on physical cpus and the functions operating
on a logical cpu number. Make the functions for physical cpus use a
pointer to a struct pcpu. This hides the knowledge about cpu addresses in
smp.c, entry[64].S and swsusp_asm64.S, thus remove the sigp.h header.
The PSW restart mechanism is used to start secondary cpus, calling a
function on an online cpu, calling a function on the ipl cpu, and for
the nmi signal. Replace the different assembler functions with a
single function restart_int_handler. The new entry point calls a function
whose pointer is stored in the lowcore of the target cpu and it can wait
for the source cpu to stop. This covers all existing use cases.
Overall the code is now simpler and there are ~380 lines less code.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 16 bit value at the lowcore location with offset 0x84 is the
cpu address that is associated with an external interrupt. Rename
the field from cpu_addr to ext_cpu_addr to make that clear.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the program interruption code and the translation exception identifier
to the pt_regs structure as 'int_code' and 'int_parm_long' and make the
first level interrupt handler in entry[64].S store the two values. That
makes it possible to drop 'prot_addr' and 'trap_no' from the thread_struct
and to reduce the number of arguments to a lot of functions. Finally
un-inline do_trap. Overall this saves 5812 bytes in the .text section of
the 64 bit kernel.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Another round of cleanup for entry[64].S, in particular the program check
handler looks more reasonable now. The code size for the 31 bit kernel
has been reduced by 616 byte and by 528 byte for the 64 bit version.
Even better the code is a bit faster as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add an explicit TIF_SYSCALL bit that indicates if a task is inside
a system call. The svc_code in the pt_regs structure is now only
valid if TIF_SYSCALL is set. With this definition TIF_RESTART_SVC
can be replaced with TIF_SYSCALL. Overall do_signal is a bit more
readable and it saves a few lines of code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a ERESTARTNOHAND/ERESTARTSYS/ERESTARTNOINTR restarting system call
do_signal will prepare the restart of the system call with a rewind of
the PSW before calling get_signal_to_deliver (where the debugger might
take control). For A ERESTART_RESTARTBLOCK restarting system call
do_signal will set -EINTR as return code.
There are two issues with this approach:
1) strace never sees ERESTARTNOHAND, ERESTARTSYS, ERESTARTNOINTR or
ERESTART_RESTARTBLOCK as the rewinding already took place or the
return code has been changed to -EINTR
2) if get_signal_to_deliver does not return with a signal to deliver
the restart via the repeat of the svc instruction is left in place.
This opens a race if another signal is made pending before the
system call instruction can be reexecuted. The original system call
will be restarted even if the second signal would have ended the
system call with -EINTR.
These two issues can be solved by dropping the early rewind of the
system call before get_signal_to_deliver has been called and by using
the TIF_RESTART_SVC magic to do the restart if no signal has to be
delivered. The only situation where the system call restart via the
repeat of the svc instruction is appropriate is when a SA_RESTART
signal is delivered to user space.
Unfortunately this breaks inferior calls by the debugger again. The
system call number and the length of the system call instruction is
lost over the inferior call and user space will see ERESTARTNOHAND/
ERESTARTSYS/ERESTARTNOINTR/ERESTART_RESTARTBLOCK. To correct this a
new ptrace interface is added to save/restore the system call number
and system call instruction length.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the save_area_64 field from the 0xe00 - 0xf00 area in the lowcore.
Use a free slot in the save_area array instead.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With this patch a new S390 shutdown trigger "restart" is added. If under
z/VM "systerm restart" is entered or under the HMC the "PSW restart" button
is pressed, the PSW located at 0 (31 bit) or 0x1a0 (64 bit) bit is loaded.
Now we execute do_restart() that processes the restart action that is
defined under /sys/firmware/shutdown_actions/on_restart. Currently the
following actions are possible: reipl (default), stop, vmcmd, dump, and
dump_reipl.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The alignment is missing for various global symbols in s390 assembly code.
With a recent gcc and an instruction like stgrl this can lead to a
specification exception if the instruction uses such a mis-aligned address.
Specify the alignment explicitely and while add it define __ALIGN for s390
and use the ENTRY define to save some lines of code.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On cpu hot remove a PFAULT CANCEL command is sent to the hypervisor
which in turn will cancel all outstanding pfault requests that have
been issued on that cpu (the same happens with a SIGP cpu reset).
The result is that we end up with uninterruptible processes where
the interrupt that would wake up these processes never arrives.
In order to solve this all processes which wait for a pfault
completion interrupt get woken up after a cpu hot remove. The worst
case that could happen is that they fault again and in turn need to
wait again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When starting a new CPU we currently jump to start_secondary() without
setting register 14 (the return address) correctly. Therefore on the stack
frame for start_secondary an invalid return address is stored. This leads
to wrong stack back traces in kernel dumps.
Example:
#00 [1f33fe48] cpu_idle at 10614a
#01 [1f33fe90] start_secondary at 54fa88
#02 [1f33feb8] (null) at 0 <--- invalid
To fix this start_secondary() is called now with basr/brasl that sets
register 14 correctly. The output of the stack backtrace looks then
like the following:
#00 [1f33fe48] cpu_idle at 10614a
#01 [1f33fe90] start_secondary at 54fa88
#02 [1f33feb8] restart_base at 54f41e <--- correct
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the code in the 31 bit entry.S code as similar as possible to the
64 bit version in entry64.S. That makes it easier to add new code to
the first level interrupt handler that affects both 31 and 64 bit kernels.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add kprobes annotations to get the massive 'probe kernel.function("*") {}'
stress test working.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix kprobes after git commit 1e54622e04
broke it. The kprobe_handler is now called with interrupts in the state
at the time of the breakpoint. The single step of the replaced instruction
is done with interrupts off which makes it necessary to enable and disable
the interupts in the kprobes code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do the setup of the stack overflow argument for the sixth system
call parameter right before the branch to the system call function.
That simplifies the system call parameter access code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Read external interrupts parameters from the lowcore in the first
level interrupt handler in entry[64].S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Read all required fields for program checks from the lowcore in the
first level interrupt handler in entry[64].S. If the context that
caused the fault was enabled for interrupts we can now re-enable the
irqs in entry[64].S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case user space is single stepped (PER) the program check handler
claims too early that IRQs are enabled on the return path.
Subsequent checks will notice that the IRQ mask in the PSW and
what lockdep thinks the IRQ mask should be do not correlate and
therefore will print a warning to the console and disable lockdep.
Fix this by doing all the work within the correct context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Copy the last breaking event address from the lowcore to a new
field in the thread_struct on each system entry. Add a new
ptrace request PTRACE_GET_LAST_BREAK and a new utrace regset
REGSET_LAST_BREAK to query the last breaking event.
This is useful for debugging wild branches in user space code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A machine check can interrupt the i/o and external interrupt handler
anytime. If the machine check occurs while the interrupt handler is
waking up from idle vtime_start_cpu can get executed a second time
and the int_clock / async_enter_timer values in the lowcore get
clobbered. This can confuse the cpu time accounting.
To fix this problem two changes are needed. First the machine check
handler has to use its own copies of int_clock and async_enter_timer,
named mcck_clock and mcck_enter_timer. Second the nested execution
of vtime_start_cpu has to be prevented. This is done in s390_idle_check
by checking the wait bit in the program status word.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The system call path in entry[64].S is run with interrupts enabled.
Remove the irq tracing check from the system call exit code. If a
program check interrupted a context enabled for interrupts do a
call to trace_irq_off_caller in the program check handler before
branching to the system call exit code.
Restructure the system call and io interrupt return code to avoid
avoid the lpsw[e] to disable machine checks.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup the #ifdef mess at io_work in entry[64].S and streamline the
TIF work code of the system call and io exit path.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
