This rips the message queue in the PL022 driver out and pushes
it into (optional) common infrastructure. Drivers that want to
use the message pumping thread will need to define the new
per-messags transfer methods and leave the deprecated transfer()
method as NULL.
Most of the design is described in the documentation changes that
are included in this patch.
Since there is a queue that need to be stopped when the system
is suspending/resuming, two new calls are implemented for the
device drivers to call in their suspend()/resume() functions:
spi_master_suspend() and spi_master_resume().
ChangeLog v1->v2:
- Remove Kconfig entry and do not make the queue support optional
at all, instead be more agressive and have it as part of the
compulsory infrastructure.
- If the .transfer() method is implemented, delete print a small
deprecation notice and do not start the transfer pump.
- Fix a bitrotted comment.
ChangeLog v2->v3:
- Fix up a problematic sequence courtesy of Chris Blair.
- Stop rather than destroy the queue on suspend() courtesy of
Chris Blair.
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since commit
commit 2f1a74e5a2
Author: eric miao <eric.miao@marvell.com>
Date: Wed Nov 21 18:50:53 2007 +0800
[ARM] pxa: make pxa2xx_spi driver use ssp_request()/ssp_free()
the ssp_type field in struct pxa2xx_spi_master is no longer available.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds DMA support for the EP93xx SPI driver. By default the DMA is
not enabled but it can be enabled by setting ep93xx_spi_info.use_dma to true
in board configuration file.
Note that the SPI driver still uses PIO for small transfers (<= 8 bytes) for
performance reasons.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.
This move got verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Fix this warning:
Documentation/spi/spidev_fdx.c: In function `do_msg':
Documentation/spi/spidev_fdx.c:61: warning: cast from pointer to integer of different size
Documentation/spi/spidev_fdx.c:64: warning: cast from pointer to integer of different size
buf should be unsigned long to match native arch on 32-bit x86 compile.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The sample application spidev_test.c is using SPI_IOC_MESSAGE ioctl to do
an SPI transfer. This ioctl returns the number of bytes successfully
transmitted or a negative error code upon erroneous completion. The
application however is returning an error if the result of the ioclt if
the return value is 1. This makes the application to fail upon 1-byte
length transfers.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:
* SPI_NO_CS ... a second 3-wire variant, where the chipselect
line is removed instead of a data line; transfers are still
full duplex.
This obviously has STRONG protocol implications since the
chipselect transitions can't be used to synchronize state
transitions with the SPI master.
* SPI_READY ... defines open drain signal that's pulled low
to pause the clock. This defines a 5-wire variant (normal
4-wire SPI plus READY) and two 4-wire variants (READY plus
each of the 3-wire flavors).
Such hardware flow control can be a big win. There are ADC
converters and flash chips that expose READY signals, but not
many host controllers support it today.
The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack. That's a mode most hardware can easily support
(unlike SPI_READY).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a doc-only patch which I hope will reduce the number of
spi_master controller driver patches starting out with a common
implementation bug.
(As in: almost every spi_master driver I see starts out with its
version of this bug. Sigh.)
It just re-emphasizes that the setup() method may be called for one
device while a transfer is active on another ... which means that most
driver implementations shouldn't touch any registers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).
Other fixes: doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make the chip info structure data optional by providing reasonable
defaults. Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.
DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently source files in the Documentation/ sub-dir can easily bit-rot
since they are not generally buildable, either because they are hidden in
text files or because there are no Makefile rules for them. This needs to
be fixed so that the source files remain usable and good examples of code
instead of bad examples.
Add the ability to build source files that are in the Documentation/ dir.
Add to Kconfig as "BUILD_DOCSRC" config symbol.
Use "CONFIG_BUILD_DOCSRC=1 make ..." to build objects from the
Documentation/ sources. Or enable BUILD_DOCSRC in the *config system.
However, this symbol depends on HEADERS_CHECK since the header files need
to be installed (for userspace builds).
Built (using cross-tools) for x86-64, i386, alpha, ia64, sparc32,
sparc64, powerpc, sh, m68k, & mips.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update SPI documentation to clarify some areas of recent confusion: clock
polarity takes effect when chipselect goes active; and zero length buffers are
OK in certain cases.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
