Tune SD_MC_INIT the same way as SD_CPU_INIT:
unset SD_BALANCE_NEWIDLE, and set SD_WAKE_BALANCE.
This improves vmark by 5%:
vmark 132102 125968 125497 messages/sec avg 127855.66 .984
vmark 139404 131719 131272 messages/sec avg 134131.66 1.033
Signed-off-by: Mike Galbraith <efault@gmx.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
# *DOCUMENTATION*
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix recursive descent in __scm_destroy().
iwl3945: fix deadlock on suspend
iwl3945: do not send scan command if channel count zero
iwl3945: clear scanning bits upon failure
ath5k: correct handling of rx status fields
zd1211rw: Add 2 device IDs
Fix logic error in rfkill_check_duplicity
iwlagn: avoid sleep in softirq context
iwlwifi: clear scanning bits upon failure
Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"
tcp: Fix recvmsg MSG_PEEK influence of blocking behavior.
netfilter: netns ct: walk netns list under RTNL
ipv6: fix run pending DAD when interface becomes ready
net/9p: fix printk format warnings
net: fix packet socket delivery in rx irq handler
xfrm: Have af-specific init_tempsel() initialize family field of temporary selector
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Block: use round_jiffies_up()
Add round_jiffies_up and related routines
block: fix __blkdev_get() for removable devices
generic-ipi: fix the smp_mb() placement
blk: move blk_delete_timer call in end_that_request_last
block: add timer on blkdev_dequeue_request() not elv_next_request()
bio: define __BIOVEC_PHYS_MERGEABLE
block: remove unused ll_new_mergeable()
__scm_destroy() walks the list of file descriptors in the scm_fp_list
pointed to by the scm_cookie argument.
Those, in turn, can close sockets and invoke __scm_destroy() again.
There is nothing which limits how deeply this can occur.
The idea for how to fix this is from Linus. Basically, we do all of
the fput()s at the top level by collecting all of the scm_fp_list
objects hit by an fput(). Inside of the initial __scm_destroy() we
keep running the list until it is empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the hrtimer_add_expires_ns() function. It should take a 'u64 ns' argument,
but rather takes an 'unsigned long ns' argument - which might only be 32-bits.
On FRV, this results in the kernel locking up because hrtimer_forward() passes
the result of a 64-bit multiplication to this function, for which the compiler
discards the top 32-bits - something that didn't happen when ktime_add_ns() was
called directly.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds three helpers:
fat_make_attrs() - makes FAT attributes from inode.
fat_make_mode() - makes mode_t from FAT attributes.
fat_save_attrs() - saves FAT attributes to inode.
Then this replaces: MSDOS_MKMODE() by fat_make_mode(), fat_attr() by
fat_make_attrs(), ->i_attrs = attr & ATTR_UNUSED by fat_save_attrs().
And for root inode, those is used with ATTR_DIR instead of bogus
ATTR_NONE.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__scm_destroy() walks the list of file descriptors in the scm_fp_list
pointed to by the scm_cookie argument.
Those, in turn, can close sockets and invoke __scm_destroy() again.
There is nothing which limits how deeply this can occur.
The idea for how to fix this is from Linus. Basically, we do all of
the fput()s at the top level by collecting all of the scm_fp_list
objects hit by an fput(). Inside of the initial __scm_destroy() we
keep running the list until it is empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1158b) adds round_jiffies_up() and friends. These
routines work like the analogous round_jiffies() functions, except
that they will never round down.
The new routines will be useful for timeouts where we don't care
exactly when the timer expires, provided it doesn't expire too soon.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Define __BIOVEC_PHYS_MERGEABLE as the default implementation of
BIOVEC_PHYS_MERGEABLE, so that its available for reuse within an
arch-specific definition of BIOVEC_PHYS_MERGEABLE.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Impact: improve wakeup affinity on NUMA systems, tweak SMP systems
Given the fixes+tweaks to the wakeup-buddy code, re-tweak the domain
balancing defaults on NUMA and SMP systems.
Turn on SD_WAKE_AFFINE which was off on x86 NUMA - there's no reason
why we would not want to have wakeup affinity across nodes as well.
(we already do this in the standard NUMA template.)
lat_ctx on a NUMA box is particularly happy about this change:
before:
| phoenix:~/l> ./lat_ctx -s 0 2
| "size=0k ovr=2.60
| 2 5.70
after:
| phoenix:~/l> ./lat_ctx -s 0 2
| "size=0k ovr=2.65
| 2 2.07
a 2.75x speedup.
pipe-test is similarly happy about it too:
| phoenix:~/sched-tests> ./pipe-test
| 18.26 usecs/loop.
| 14.70 usecs/loop.
| 14.38 usecs/loop.
| 10.55 usecs/loop. # +WAKE_AFFINE on domain0+domain1
| 8.63 usecs/loop.
| 8.59 usecs/loop.
| 9.03 usecs/loop.
| 8.94 usecs/loop.
| 8.96 usecs/loop.
| 8.63 usecs/loop.
Also:
- disable SD_BALANCE_NEWIDLE on NUMA and SMP domains (keep it for siblings)
- enable SD_WAKE_BALANCE on SMP domains
Sysbench+postgresql improves all around the board, quite significantly:
.28-rc3-11474e2c .28-rc3-11474e2c-tune
-------------------------------------------------
1: 571 688 +17.08%
2: 1236 1206 -2.55%
4: 2381 2642 +9.89%
8: 4958 5164 +3.99%
16: 9580 9574 -0.07%
32: 7128 8118 +12.20%
64: 7342 8266 +11.18%
128: 7342 8064 +8.95%
256: 7519 7884 +4.62%
512: 7350 7731 +4.93%
-------------------------------------------------
SUM: 55412 59341 +6.62%
So it's a win both for the runup portion, the peak area and the tail.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For "unlock" cycles to 16bit devices in 8bit compatibility mode we need
to use the byte addresses 0xaaa and 0x555. These effectively match
the word address 0x555 and 0x2aa, except the latter has its low bit set.
Most chips don't care about the value of the 'A-1' pin in x8 mode,
but some -- like the ST M29W320D -- do. So we need to be careful to
set it where appropriate.
cfi_send_gen_cmd is only ever passed addresses where the low byte
is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are
affected by this patch, by masking in the extra low bit when the device
is known to be in compatibility mode.
[dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa]
v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile
I'm writing this patch way to late at night.
v3: Bring all of the work back into cfi_build_cmd_addr
including calling of map_bankwidth(map) and cfi_interleave(cfi)
So every caller doesn't need to.
v2: Only modified the address if we our device_type is larger than our
bus width.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The changes to deliver hardware accelerated VLAN packets to packet
sockets (commit bc1d0411) caused a warning for non-NAPI drivers.
The __vlan_hwaccel_rx() function is called directly from the drivers
RX function, for non-NAPI drivers that means its still in RX IRQ
context:
[ 27.779463] ------------[ cut here ]------------
[ 27.779509] WARNING: at kernel/softirq.c:136 local_bh_enable+0x37/0x81()
...
[ 27.782520] [<c0264755>] netif_nit_deliver+0x5b/0x75
[ 27.782590] [<c02bba83>] __vlan_hwaccel_rx+0x79/0x162
[ 27.782664] [<f8851c1d>] atl1_intr+0x9a9/0xa7c [atl1]
[ 27.782738] [<c0155b17>] handle_IRQ_event+0x23/0x51
[ 27.782808] [<c015692e>] handle_edge_irq+0xc2/0x102
[ 27.782878] [<c0105fd5>] do_IRQ+0x4d/0x64
Split hardware accelerated VLAN reception into two parts to fix this:
- __vlan_hwaccel_rx just stores the VLAN TCI and performs the VLAN
device lookup, then calls netif_receive_skb()/netif_rx()
- vlan_hwaccel_do_receive(), which is invoked by netif_receive_skb()
in softirq context, performs the real reception and delivery to
packet sockets.
Reported-and-tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers. Implement a horkage to skip the mod16 check and apply
it to the quantum device.
This is reported by John Clark in the following thread.
http://thread.gmane.org/gmane.linux.ide/34748
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
io mapping: clean up #ifdefs
io mapping: improve documentation
i915: use io-mapping interfaces instead of a variety of mapping kludges
resources: add io-mapping functions to dynamically map large device apertures
x86: add iomap_atomic*()/iounmap_atomic() on 32-bit using fixmaps
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
i915: Add GEM ioctl to get available aperture size.
drm/radeon: fixup further bus mastering confusion.
build fix: CONFIG_DRM_I915=y && CONFIG_ACPI=n
Impact: cleanup
clean up ifdefs: change #ifdef CONFIG_X86_32/64 to
CONFIG_HAVE_ATOMIC_IOMAP.
flip around the #ifdef sections to clean up the structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This will let userland know when to submit its batchbuffers, before they get
too big to fit in the aperture.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
Impact: add new generic io_map_*() APIs
Graphics devices have large PCI apertures which would consume a significant
fraction of a 32-bit address space if mapped during driver initialization.
Using ioremap at runtime is impractical as it is too slow.
This new set of interfaces uses atomic mappings on 32-bit processors and a
large static mapping on 64-bit processors to provide reasonable 32-bit
performance and optimal 64-bit performance.
The current implementation sits atop the io_map_atomic fixmap-based
mechanism for 32-bit processors.
This includes some editorial suggestions from Randy Dunlap for
Documentation/io-mapping.txt
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: introduce new APIs, separate kmap code from CONFIG_HIGHMEM
This takes the code used for CONFIG_HIGHMEM memory mappings except that
it's designed for dynamic IO resource mapping.
These fixmaps are available even with CONFIG_HIGHMEM turned off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
