Some commands don't work in its example doc. The patch will fix it.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 patches)
revert "mm: fix-up zone present pages"
tmpfs: change final i_blocks BUG to WARNING
tmpfs: fix shmem_getpage_gfp() VM_BUG_ON
mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address
mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures"
rapidio: fix kernel-doc warnings
swapfile: fix name leak in swapoff
memcg: fix hotplugged memory zone oops
mips, arc: fix build failure
memcg: oom: fix totalpages calculation for memory.swappiness==0
mm: fix build warning for uninitialized value
mm: add anon_vma_lock to validate_mm()
oom_badness() takes a totalpages argument which says how many pages are
available and it uses it as a base for the score calculation. The value
is calculated by mem_cgroup_get_limit which considers both limit and
total_swap_pages (resp. memsw portion of it).
This is usually correct but since fe35004fbf ("mm: avoid swapping out
with swappiness==0") we do not swap when swappiness is 0 which means
that we cannot really use up all the totalpages pages. This in turn
confuses oom score calculation if the memcg limit is much smaller than
the available swap because the used memory (capped by the limit) is
negligible comparing to totalpages so the resulting score is too small
if adj!=0 (typically task with CAP_SYS_ADMIN or non zero oom_score_adj).
A wrong process might be selected as result.
The problem can be worked around by checking mem_cgroup_swappiness==0
and not considering swap at all in such a case.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) tx_filtered/ps_tx_buf queues need to be accessed with the SKB queue
lock, from Arik Nemtsov.
2) Don't call 802.11 driver's filter configure method until it's
actually open, from Felix Fietkau.
3) Use ieee80211_free_txskb otherwise we leak control information.
From Johannes Berg.
4) Fix memory leak in bluetooth UUID removal,f rom Johan Hedberg.
5) The shift mask trick doesn't work properly when 'optname' is out of
range in do_ip_setsockopt(). Use a straightforward switch statement
instead, the compiler emits essentially the same code but without
the missing range check. From Xi Wang.
6) Fix when we call tcp_replace_ts_recent() otherwise we can
erroneously accept a too-high tsval. From Eric Dumazet.
7) VXLAN bug fixes, mostly to do with VLAN header length handling, from
Alexander Duyck.
8) Missing return value initialization for IPV6_MINHOPCOUNT socket
option handling. From Hannes Frederic.
9) Fix regression in tasklet handling in jme/ksz884x/xilinx drivers,
from Xiaotian Feng.
10) At smsc911x driver init time, we don't know if the chip is in word
swap mode or not. However we do need to wait for the control
register's ready bit to be set before we program any other part of
the chip. Adjust the wait loop to account for this. From Kamlakant
Patel.
11) Revert erroneous MDIO bus unregister change to mdio-bitbang.c
12) Fix memory leak in /proc/net/sctp/, from Tommi Rantala.
13) tilegx driver registers IRQ with NULL name, oops, from Simon Marchi.
14) TCP metrics hash table kzalloc() based allocation can fail, back
down to using vmalloc() if it does. From Eric Dumazet.
15) Fix packet steering out-of-order delivery regression, from Tom
Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net-rps: Fix brokeness causing OOO packets
tcp: handle tcp_net_metrics_init() order-5 memory allocation failures
batman-adv: process broadcast packets in BLA earlier
batman-adv: don't add TEMP clients belonging to other backbone nodes
batman-adv: correctly pass the client flag on tt_response
batman-adv: fix tt_global_entries flags update
tilegx: request_irq with a non-null device name
net: correct check in dev_addr_del()
tcp: fix retransmission in repair mode
sctp: fix /proc/net/sctp/ memory leak
Revert "drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free"
net/smsc911x: Fix ready check in cases where WORD_SWAP is needed
drivers/net: fix tasklet misuse issue
ipv4/ip_vti.c: VTI fix post-decryption forwarding
brcmfmac: fix typo in CONFIG_BRCMISCAN
vxlan: Update hard_header_len based on lowerdev when instantiating VXLAN
vxlan: fix a typo.
ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value
doc/net: Fix typo in netdev-features.txt
vxlan: Fix error that was resulting in VXLAN MTU size being 10 bytes too large
...
This is mostly a revert of 01dc52ebdf ("oom: remove deprecated oom_adj")
from Davidlohr Bueso.
It reintroduces /proc/pid/oom_adj for backwards compatibility with earlier
kernels. It simply scales the value linearly when /proc/pid/oom_score_adj
is written.
The major difference is that its scheduled removal is no longer included
in Documentation/feature-removal-schedule.txt. We do warn users with a
single printk, though, to suggest the more powerful and supported
/proc/pid/oom_score_adj interface.
Reported-by: Artem S. Tashkinov <t.artem@lycos.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
Pull driver core fixes from Greg Kroah-Hartman:
"Here are a number of firmware core fixes for 3.7, and some other minor
fixes. And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation:Chinese translation of Documentation/arm64/memory.txt
Documentation:Chinese translation of Documentation/arm64/booting.txt
Documentation:Chinese translation of Documentation/IRQ.txt
firmware loader: document kernel direct loading
sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()
dynamic_debug: Remove unnecessary __used
firmware loader: sync firmware cache by async_synchronize_full_domain
firmware loader: let direct loading back on 'firmware_buf'
firmware loader: fix one reqeust_firmware race
firmware loader: cancel uncache work before caching firmware
The irq_to_gpio() is old, most platforms use GENERIC_GPIO framework
and don't support this API anymore.
The i.MX6q sabrelite platform equips an egalax touchscreen controller,
and this platform already transfered to GENERIC_GPIO framework, to
support this driver, we use a more generic way to get gpio.
Add a return value checking for waking up the controller in the probe
function, this guarantee only a workable device can pass init.
[dmitry.torokhov@gmail.com: Make driver depend on CONFIG_OF as it is
now required.]
Acked-by Zhang Jiejing <jiejing.zhang@freescale.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull pinctrl fixes from Linus Walleij:
"This fixes a few pinctrl problems seen since v3.7-rc1:
- Section tagging for init code
- Use proper pointers to lookup struct device * in the bcm2835
(a.k.a. Raspberry Pi)
- Remove duplicate #includes
- Fix bad return values in errorpath
- Remove extraneous pull function from the sirf driver causing build
errors
- Provide compilation stubs for the Nomadik pinctrl driver when used
with legacy systems without PRCMU units
- Various irqdomain fixes in the Nomadik driver as predicted
- Various smallish bugs in the Tegra driver, most also targeted for
stable
- Removed a deadlocking mutex in the groups debugfs show function"
* tag 'pinctrl-v3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: pass DT node to the irqdomain
pinctrl/nomadik: use zero as default irq_start
pinctrl: fix missing unlock on error in pinctrl_groups_show()
pinctrl/nomadik: use irq_create_mapping()
pinctrl: remove mutex lock in groups show
pinctrl: tegra: correct bank for pingroup and drv pingroup
pinctrl: tegra: set low power mode bank width to 2
dt: Document: correct tegra20/30 pinctrl slew-rate name
Pull core kernel fixes from Ingo Molnar:
"Two small fixes"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: Reflect the new location of the NMI watchdog info
nohz: Fix idle ticks in cpu summary line of /proc/stat
Pull hwmon fixes from Guenter Roeck:
"Drop some leftover dependencies on CONFIG_EXPERIMENTAL, and add
support for Intel Atom CE4110/4150/4170."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Add support for Atom CE4110/4150/4170
Documentation/hwmon: remove CONFIG_EXPERIMENTAL
hwmon: (pmbus) remove CONFIG_EXPERIMENTAL
Pull media fixes from Mauro Carvalho Chehab:
"Media fixes for:
- one Kconfig fix patch;
- one patch fixing DocBook breakage due to the drivers/media UAPI
changes;
- the remaining UAPI media changes (DVB API).
I'm aware that is is a little late for the UAPI renames for the DVB
API, but IMHO, it is better to merge it for 3.7, due to two reasons:
1) There is a major rename at 3.7 (not only uapi changes, but also
the entire media drivers were reorganized on 3.7, in order to
simplify the Kconfig logic, and easy drivers selection, especially
for hybrid devices). By confining all those renames there at 3.7
it will cause all the harm at for media developers on just one
shot. Stable backports upstream and at distros will likely
welcome it as well, as they won't need to check what changed on
3.7 and what was postponed for on 3.8.
2) The V4L2 DocBook Makefile creates a cross-reference between the
media API headers and the specs. This helps us _a_lot_ to be sure
that all API improvements are properly documented. Every time a
header changes from one place to another, DocBook/media/Makefile
needs to be patched. Currently, the DocBook breakage patch
depends on the DVB UAPI."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Kconfig: Fix dependencies for driver autoselect options
DocBook/media/Makefile: Fix build due to uapi breakage
UAPI: (Scripted) Disintegrate include/linux/dvb
