commit 08a3b3b1c2 upstream.
The iounmap(ehci->ohci_hcctrl_reg); should be the first thing we do
because the ioremap() was the last thing we did. Also if we hit any of
the goto statements in the original code then it would have led to a
NULL dereference of "ehci". This bug was introduced in: 796bcae736
"USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]"
I modified the few lines in front a little so that my code didn't
obscure the return success code path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a1669b2c64 upstream.
The code to increment the TRB pointer has a slight ambiguity that could
lead to a bug on different compilers. The ANSI C specification does not
specify the precedence of the assignment operator over the postfix
operator. gcc 4.4 produced the correct code (increment the pointer and
assign the value), but a MIPS compiler that one of John's clients used
assigned the old (unincremented) value.
Remove the unnecessary assignment to make all compilers produce the
correct assembly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 2d62f3eea9 upstream.
After software resets an xHCI host controller, it must wait for the
"Controller Not Ready" (CNR) bit in the status register to be cleared.
Software is not supposed to ring any doorbells or write to any registers
except the status register until this bit is cleared.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ed07453fd3 upstream.
When the run bit is set in the xHCI command register, it may take a few
microseconds for the host to start running. We cannot ring any doorbells
until the host is actually running, so wait until the status register says
the host is running.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Shinya Saito <shinya.saito.sx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 44ebd037c5 upstream.
The length of the scatter gather list a driver can enqueue is limited by
the bus' sg_tablesize to 62 entries. Each entry will be described by at
least one transfer request block (TRB). If the entry's buffer crosses a
64KB boundary, then that entry will have to be described by two or more
TRBs. So even if the USB device driver respects sg_tablesize, the whole
scatter list may take more than 62 TRBs to describe, and won't fit on
the ring.
Don't assume that an empty ring means there is enough room on the
transfer ring. The old code would unconditionally queue this too-large
transfer, and over write the beginning of the transfer. This would mean
the cycle bit was unchanged in those overwritten transfers, causing the
hardware to think it didn't own the TRBs, and the host would seem to
hang.
Now drivers may see submit_urb() fail with -ENOMEM if the transfers are
too big to fit on the ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1624ae1c19 upstream.
When the USB core installs a new interface, it unconditionally clears the
halts on all the endpoints on the new interface. Usually the xHCI host
needs to know when an endpoint is reset, so it can change its internal
endpoint state. In this case, it doesn't care, because the endpoints were
never halted in the first place.
To avoid issuing a redundant Reset Endpoint command, the xHCI driver looks
at xhci_virt_ep->stopped_td to determine if the endpoint was actually
halted. However, the functions that handle the stall never set that
variable to NULL after it dealt with the stall. So if an endpoint stalled
and a Reset Endpoint command completed, and then the class driver tried to
install a new alternate setting, the xHCI driver would access the old
xhci_virt_ep->stopped_td pointer. A similar problem occurs if the
endpoint has been stopped to cancel a transfer.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9238f25d5d upstream.
For periodic endpoints, we must let the xHCI hardware know the maximum
payload an endpoint can transfer in one service interval. The xHCI
specification refers to this as the Maximum Endpoint Service Interval Time
Payload (Max ESIT Payload). This is used by the hardware for bandwidth
management and scheduling of packets.
For SuperSpeed endpoints, the maximum is calculated by multiplying the max
packet size by the number of bursts and the number of opportunities to
transfer within a service interval (the Mult field of the SuperSpeed
Endpoint companion descriptor). Devices advertise this in the
wBytesPerInterval field of their SuperSpeed Endpoint Companion Descriptor.
For high speed devices, this is taken by multiplying the max packet size by the
"number of additional transaction opportunities per microframe" (the high
bits of the wMaxPacketSize field in the endpoint descriptor).
For FS/LS devices, this is just the max packet size.
The other thing we must set in the endpoint context is the Average TRB
Length. This is supposed to be the average of the total bytes in the
transfer descriptor (TD), divided by the number of transfer request blocks
(TRBs) it takes to describe the TD. This gives the host controller an
indication of whether the driver will be enqueuing a scatter gather list
with many entries comprised of small buffers, or one contiguous buffer.
It also takes into account the number of extra TRBs you need for every TD.
This includes No-op TRBs and Link TRBs used to link ring segments
together. Some drivers may choose to chain an Event Data TRB on the end
of every TD, thus increasing the average number of TRBs per TD. The Linux
xHCI driver does not use Event Data TRBs.
In theory, if there was an API to allow drivers to state what their
bandwidth requirements are, we could set this field accurately. For now,
we set it to the same number as the Max ESIT payload.
The Average TRB Length should also be set for bulk and control endpoints,
but I have no idea how to guess what it should be.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1cf62246c0 upstream.
A SuperSpeed interrupt or isochronous endpoint can define the number of
"burst transactions" it can handle in a service interval. This is
indicated by the "Mult" bits in the bmAttributes of the SuperSpeed
Endpoint Companion Descriptor. For example, if it has a max packet size
of 1024, a max burst of 11, and a mult of 3, the host may send 33
1024-byte packets in one service interval.
We must tell the xHCI host controller the number of multiple service
opportunities (mults) the device can handle when the endpoint is
installed. We do that by setting the Mult field of the Endpoint Context
before a configure endpoint command is sent down. The Mult field is
invalid for control or bulk SuperSpeed endpoints.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit fcf7d2141f upstream.
This patch (as1371) fixes a small bug in ohci-hcd. The HCD already
knows how many ports the controller has; there's no need to go looking
at the root hub's usb_device structure to find out. Especially since
the root hub's maxchild value is set correctly only while the root hub
is bound to the hub driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0e5f231bc1 upstream.
This patch (as1369) fixes a problem in ehci-hcd. Some controllers
occasionally run into trouble when the driver reclaims siTDs too
quickly. This can happen while streaming audio; it causes the
controller to crash.
The patch changes siTD reclamation to work the same way as iTD
reclamation: Completed siTDs are stored on a list and not reused until
at least one frame has passed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d835933436 upstream.
fix the problem that when a USB hub is attached to the r8a66597-hcd and
a device is removed from that hub, it's likely that a kernel panic follows.
Reported-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1d68064a7d upstream.
When a signal interrupts a Configure Endpoint command, the cmd_completion used
in xhci_configure_endpoint() is not re-initialized and the
wait_for_completion_interruptible_timeout() will return failure. Initialize
cmd_completion in xhci_configure_endpoint().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1082f57abf upstream.
The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.
After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.
This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 92bc3648e6 upstream.
When isochronous URBs are shorter than one frame and when more than one
ITD in a frame has been completed before the interrupt can be handled,
scan_periodic() completes the URBs in the order in which they are found
in the descriptor list. Therefore, the descriptor list must contain the
ITDs in the correct order, i.e., a new ITD must be linked in after any
previous ITDs of the same endpoint.
This should fix garbled capture data in the USB audio drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d23356da71 upstream.
When hardware is removed on a Stratus, the system may crash like this:
ACPI: PCI interrupt for device 0000:7c:00.1 disabled
Trying to free nonexistent resource <00000000a8000000-00000000afffffff>
Trying to free nonexistent resource <00000000a4800000-00000000a480ffff>
uhci_hcd 0000:7e:1d.0: remove, state 1
usb usb2: USB disconnect, address 1
usb 2-1: USB disconnect, address 2
Unable to handle kernel paging request at 0000000000100100 RIP:
[<ffffffff88021950>] :uhci_hcd:uhci_scan_schedule+0xa2/0x89c
#4 [ffff81011de17e50] uhci_scan_schedule at ffffffff88021918
#5 [ffff81011de17ed0] uhci_irq at ffffffff88023cb8
#6 [ffff81011de17f10] usb_hcd_irq at ffffffff801f1c1f
#7 [ffff81011de17f20] handle_IRQ_event at ffffffff8001123b
#8 [ffff81011de17f50] __do_IRQ at ffffffff800ba749
This occurs because an interrupt scans uhci->skelqh, which is
being freed. We do the right thing: disable the interrupts in the
device, and do not do any processing if the interrupt is shared
with other source, but it's possible that another CPU gets
delayed somewhere (e.g. loops) until we started freeing.
The agreed-upon solution is to wait for interrupts to play out
before proceeding. No other bareers are neceesary.
A backport of this patch was tested on a 2.6.18 based kernel.
Testing of 2.6.32-based kernels is under way, but it takes us
forever (months) to turn this around. So I think it's a good
patch and we should keep it.
Tracked in RH bz#516851
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 05197921ff upstream.
According "5.3.6 Capability Parameters (HCCPARAMS)" of xHCI rev0.96 spec,
value of xECP register indicates a relative offset, in 32-bit words,
from Base to the beginning of the first extended capability.
The wrong calculation will cause BIOS handoff fail (not handoff from BIOS)
in some platform with BIOS USB legacy sup support.
Signed-off-by: Edward Shao <laface.tw@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8740cc7d0c upstream.
i2c_board_info doesn't contain a member called name. i2c_register_client
call does not exist.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 2717568e7c upstream.
This implements the same D-cache flushing logic for r8a66597-hcd as
Catalin's isp1760 (http://patchwork.kernel.org/patch/76391/) change,
with the same note applying here as well:
When the HDC driver writes the data to the transfer buffers it
pollutes the D-cache (unlike DMA drivers where the device writes
the data). If the corresponding pages get mapped into user space,
there are no additional cache flushing operations performed and
this causes random user space faults on architectures with
separate I and D caches (Harvard) or those with aliasing D-cache.
This fixes up crashes during USB boot on SH7724 and others:
http://marc.info/?l=linux-sh&m=126439837308912&w=2
Reported-by: Goda Yusuke <goda.yusuke@renesas.com>
Tested-by: Goda Yusuke <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e5ff15bec9 upstream.
This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 49d0f078f4 upstream.
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit cec3a53c7f upstream.
This patch (as1321) fixes a problem with EHCI and UHCI root-hub
suspends: If the suspend occurs while a port is trying to resume, the
resume doesn't finish and simply gets lost. When remote wakeup is
enabled, this is undesirable behavior.
The patch checks first to see if any port resumes are in progress, and
if they are then it fails the root-hub suspend with -EBUSY.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1b9a38bfa6 upstream.
This patch (as1320) fixes two problems related to interrupt-URB
scheduling in ehci-hcd.
URBs with an interval of 2 or 4 microframes aren't handled.
For the time being, the patch reduces to interval to 1 uframe.
URBs are constrained to have an interval no larger than 1024
frames by usb_submit_urb(). But some EHCI controllers allow
use of a schedule as short as 256 frames; for these
controllers we may have to decrease the interval to the
actual schedule length.
The second problem isn't very significant since few devices expose
interrupt endpoints with an interval larger than 256 frames. But the
first problem is critical; it will prevent the kernel from working
with devices having interrupt intervals of 2 or 4 uframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Glynn Farrow <farrowg@sg.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
