Unless there will be any objection here, I suggest consider the
following patch which simply removes the code for the
-DI_WISH_WORLD_WERE_PERFECT in the three methods which use it.
The compilation errors we get when using -DI_WISH_WORLD_WERE_PERFECT
show that this code was not built and not used for really a long time.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set proper net and mark a new device as NETNS_LOCAL before registering.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I.e. replace init_net stubs in ip_route_output_key() calls.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just move all the hashes on the sit_net structure and
patch the rest of the code appropriately.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and register one in sit_init_net, use sitn->fb_tunnel_dev
over the code and unregister one in sit_exit_net.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace introduced in the previous patch init_net stubs
with the proper net pointer.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
... to make them prepared for future hashes and fallback device
move on the struct sit_net.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the Linux the Intra-Site Automatic Tunnel Addressing
Protocol (ISATAP) implementation. It places the ISATAP potential router
list (PRL) in the kernel and adds three new private ioctls for PRL
management.
[Add several changes of structure name, constant names etc. - yoshfuji]
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Add an netns parameter to ip6_route_output. That will allow to access
to the right routing table for outgoing traffic.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four tunnel drivers (ip_gre, ipip, ip6_tunnel and sit) can receive a
pre-defined name for a device from the userspace. Since these drivers
call the register_netdevice() (rtnl_lock, is held), which does _not_
generate the device's name, this name may contain a '%' character.
Not sure how bad is this to have a device with a '%' in its name, but
all the other places either use the register_netdev(), which call the
dev_alloc_name(), or explicitly call the dev_alloc_name() before
registering, i.e. do not allow for such names.
This had to be prior to the commit 34cc7b, but I forgot to number the
patches and this one got lost, sorry.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the added dev_alloc_name() call to create tunnel device name,
rather than iterate in a hand-made loop with an artificial limit.
Thanks Patrick for noticing this.
[ The way this works is, when the device is actually registered,
the generic code noticed the '%' in the name and invokes
dev_alloc_name() to fully resolve the name. -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to propagate it down to the ip_route_output_flow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to the change already done for IPIP tunnels.
Once created, a SIT tunnel can't be bound to another device.
To reproduce:
# create a tunnel:
ip tunnel add tunneltest0 mode sit remote 10.0.0.1 dev eth0
# try to change the bounding device from eth0 to eth1:
ip tunnel change tunneltest0 dev eth1
# show the result:
ip tunnel show tunneltest0
tunneltest0: ipv6/ip remote 10.0.0.1 local any dev eth0 ttl inherit
Notice the bound device has not changed from eth0 to eth1.
This patch fixes it. When changing the binding, it also recalculates the
MTU according to the new bound device's MTU.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes support for the Intra-Site Automatic Tunnel
Addressing Protocol (ISATAP) per RFC4214. It uses the SIT
module, and is configured using extensions to the "iproute2"
utility. The diffs are specific to the Linux 2.6.24-rc2 kernel
distribution.
This version includes the diff for ./include/linux/if.h which was
missing in the v2.4 submission and is needed to make the
patch compile. The patch has been installed, compiled and
tested in a clean 2.6.24-rc2 kernel build area.
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some places, the result of skb_headroom() is compared to an unsigned
integer, and in others, the result is compared to a signed integer. Make
the comparisons consistent and correct.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
