Removes superh board specific configuration from the header file. These boards
will instead be configured using platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes sure SMC_insw()/SMC_outsw() are defined for the
default configuration. Without this change BUG()s will be triggered
when using 16-bit only platform data and the default configuration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch introduces struct smc91x_platdata and modifies the driver so
bus width is checked during run time using SMC_nBIT() instead of
SMC_CAN_USE_nBIT.
V2 keeps static configuration lean using SMC_DYNAMIC_BUS_CONFIG.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Pass a private data pointer to macros and functions. This makes it easy
to later on make run time decisions. This patch does not change any logic.
These changes should be optimized away during compilation.
V2 changes the macro argument name from "priv" to "lp".
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds LAN91C111 ethernet interface support for zylonite
(a.k.a Marvell's PXA3xx Development Platform) with smc91x driver.
It would be better if a patch would support zylonite along with all
other PXA boards with a single binary of smc91x driver, but it looks
quite difficult for the moment, so ugly #ifdef is still used here.
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PXA DMA support code for smc91x doesn't pass a struct device to
the dma_*map_single() functions, which leads to an oops in the dma
bounce code. We have a struct device which was used to probe the
SMC chip. Use it.
(This patch is slightly larger because it requires struct smc_local
to move into the header file.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SH boards in general only wire this up in 8 or 16-bit mode, and
as we never had the wrappers for 32-bit mode defined, SMC_CAN_USE_32BIT
caused build failure for the non-Solution Engine boards. This gets it
building again.
Also kill off the straggling set_irq_type() definition, this is left
over cruft that was missed when the rest of it switched to IRQ flags.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
--
drivers/net/smc91x.h | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current smc91x I/O routines ifdef the solution engine subtypes
individually, which is rather bogus, as they can simply use
CONFIG_SOLUTION_ENGINE instead. This fixes it for some of the other
solution engines that weren't included in the ifdef list (SH7206
specifically).
There are also inb/outb definitions which are totally bogus (missing
brackets in _both_ cases, SMC_CAN_USE_8BIT == 0, and even better, they
try to use a 16-bit access to fake 8-bit access). Kill that nonsense off
completely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
--
drivers/net/smc91x.h | 5 +----
1 file changed, 1 insertion(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch supports SuperH of smc91x.
smc91x installed on the board of SuperH comes to work by applying this patch.
Please apply this patch .
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This looks like a result of too many auto-merges. The
CONFIG_ARCH_VERSATILE case was handled a total of 6 times.
This kills 5 of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
--
drivers/net/smc91x.h | 90 ---------------------------------------------------
1 file changed, 90 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
On Fri, 20 Oct 2006 22:50:40 +0100
Russell King <rmk@arm.linux.org.uk> wrote:
> On Fri, Oct 20, 2006 at 02:42:04PM -0700, akpm@osdl.org wrote:
> > We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
> > generic IRQ layer will complain thusly:
>
> I don't think I heard anything back from my previous suggestion that
> the IRQ flags are passed through the platform device IRQ resource.
>
> Doing so would avoid adding yet another platform specific block into
> the file.
>
> BTW, Integrator platforms will also suffer from this, which will add
> another ifdef to this header.
>
> Let's do it right and arrange to pass these flags from the platform
> code. It's not like they're in a critical path.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
