The JFFS2 requests OOB function from column 0.
But the oobtest in nand-tests doesn't.
So we only exit loop only when column start with 0.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Here it's not the case: all the entries are occupied by
OOB chunks. Therefore, once we get into a loop like
for (free = this->ecclayout->oobfree; free->length; ++free) {
}
we might end up scanning past the real oobfree array.
Probably the best way out, as the same thing might happen for common NAND
as well, is to check index against MTD_MAX_OOBFREE_ENTRIES.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Remove waitqueue, 'exiting' flag and completion; use kthread APIs instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
thread_run is used intead of kernel_thread, daemonize, and mucking
around blocking signals directly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is on a custom board with a mapping driver access to an ST
M50LPW080 chip. This chip is probed successfully with
do_map_probe("jedec_probe",...). If I use the mtdchar interface to
perform unlock->erase->program->lock on any of the 16 eraseblocks in the
chip, the chip is left in FL_STATUS mode while the data structures
believe that the chip is in FL_READY mode. Hence, any subsequent reads
to any flash byte results in 0x80 being read.
Signed-off-by: Shashi Rao <shashi@sun.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A new module parameter has been added called 'overridesize',
which overrides the size that would be determined by the
ID bytes. 'overridesize' is specified in erase blocks and
as the exponent of a power of two e.g. 5 means a size of
32 erase blocks.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
New module parameters have been added to nandsim to
simulate:
bitflips random bit flips
badblocks blocks that are initially marked bad
weakblocks blocks that fail to erase after a
small number of erase cycles
weakpages pages that fail to write after a
small number of successful writes
gravepages pages that fail to read after a
small number of successful reads
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Enhance nandsim to be able to create more than 1 partition.
A new module parameter 'parts' may be used to specify partition
sizes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is a slight bug in nand_default_block_markbad, where the offset is
cast to an integer, prior to being shifted. This means that on large
offsets, it is incorrectly doing a signed shift & losing bits. Fixed
this by doing the cast after the shift (as is done elsewhere in the code).
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for AT26Fxxx dataflash devices. These devices have a quite different
commandset than the AT45xxx chips, which are handled by at91_dataflash.c, so a
combined driver turned out to be more ugly than useful.
Tested only on AT26F004.
Signed-off-by: Hans-Jürgen Koch <hjk@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The ops.len member is not initialized, because it is unused for this
operation. The length check needs to use ops.ooblen instead
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use the functions in the ecc structure instead of the default ones,
so the override by the board driver is effective also for software ecc
code paths.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
o A dependency on the processor architecture does not make sense;
delete it.
o The Alchemy and MTX drivers requires MTD_PARTITIONS and MTD_CFI to work,
make those dependencies.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Classify the page data and oob buffer
and it prevents the memory fragementation (writesize + oobsize)
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When transferring/filling of the oob is finished in OOB_AUTO, we exit the loop
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
