Only show debug from tda18271_set_standby_mode if DBG_ADV is set.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Abort rf band calibration loop for the TDA18271HD/C2 if an error is detected.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build bug in v2.6.26-rc1:
drivers/built-in.o: In function `cinergyt2_probe':
cinergyT2.c:(.text+0xb6117): undefined reference to `input_allocate_device'
cinergyT2.c:(.text+0xb6230): undefined reference to `input_register_device'
cinergyT2.c:(.text+0xb623d): undefined reference to `input_free_device'
with the following config:
http://redhat.com/~mingo/misc/config-Sun_May__4_22_06_54_CEST_2008.bad
The reason for the bug is that the cinergyT2 driver depends on
CONFIG_INPUT functionality, but if INPUT is modular it's still possible
to build CONFIG_DVB_CINERGYT2=y - which leads to missing symbols.
The solution is to make DVB_CINERGYT2 dependent on INPUT.
[ This solves the build problem - i have not tested the driver on this card. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix undefined references in au0828:
depends on USB and select VIDEO_TVEEPROM
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build failure in v2.6.26-rc1:
MODPOST 424 modules
ERROR: "tveeprom_hauppauge_analog" [drivers/media/video/au0828/au0828.ko] undefined!
ERROR: "tveeprom_read" [drivers/media/video/au0828/au0828.ko] undefined!
with this config:
http://redhat.com/~mingo/misc/config-Sat_May__3_22_28_58_CEST_2008.bad
this patch does what other video drivers do to utilize the
VIDEO_TVEEPROM functionality (and this resolves the build problem) - but
i have not checked it on real hardware and i have not checked whether
the fix is complete.
selections, so some items might still be missing - just not triggered
with this specific config.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following build error:
drivers/built-in.o: In function `xc_load_fw_and_init_tuner':
xc5000.c:(.text+0x2dacd): undefined reference to `request_firmware'
xc5000.c:(.text+0x2daf0): undefined reference to `release_firmware'
xc5000.c:(.text+0x2db85): undefined reference to `release_firmware'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change addresses kernel bug #10459: In kernel 2.6.25 the
budget_av driver polls for an CI slot in 100ms intervals (because no
interrupt solution for budget_av cards is feasible due to HW reasons).
If no CI/CAM is connected to the DVB card, polling times out only after 250ms.
This periodic polling leads to high CPU load.
The change increases the polling interval for empty slots from 100ms to 5s.
Intervals for remaining slot states (invalid, in progress, ready) are unchanged,
as they are either temporary conditions or no timeout should occur.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx23885 driver used to use dvb-pll for LG-TDVS-H064F support on the
FusionHDTV5 Express. This has since been converted to use tuner-simple
instead, once digital tuning support was added to tuner-simple.
Since cx23885 no longer uses dvb-pll, remove the #include "dvb-pll.h",
and the DVB_PLL Kconfig selection.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver uses some sysfs helper functions that are available only for legacy
drivers. It also requires linux/mm.h.
This patch fixes compiliation when not in compat mode.
Thanks to Ingo Molnar for identifying this issue.
Acked-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Both mt9v022 and mt9m001 cameras are controlled over the I2C bus.
Respectively, their drivers require I2C to be built successfully.
Thanks to Ingo Molnar for reporting the build-breakage.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As pointed by Andrew Morton, the error testing were wrong. After reviewing
tea5767, it were returning a positive value for errors.
So, the double errors were cancelling each other.
This patch fix it properly. It also considers any positive value as ok, on
tuner-core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
