The node for DMA2 in the MPC8610 HPCD device tree has the wrong compatible
properties. This breaks the DMA driver and the sound driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dtbImage.* and several zImage. targets get created but never cleaned up.
Also, moved zImage to the clean-files line associated with all other image
results (was previously duplicated).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PowerPC 440EP, 440GR, 440EPx, and 440GRx chips have an issue that
causes the PLB3-to-PLB4 bridge to wait indefinitely for transaction
requests that cross the end-of-memory-range boundary. Since the DDR
controller only returns the valid portion of a read request, the bridge
will prevent other PLB masters from completing their transactions.
This implements the recommended workaround for this errata for chips that
use older versions of firmware that do not already handle it. The last
4KiB of memory are hidden from the kernel to prevent the problem
transactions from occurring.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.
Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.
defconfig and board file updated appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch is fixes the sequoia.dts device tree file to use the values defined
in the 440Epx data sheet from AMCC.
That fixes an issue where some devices, including graphics cards, would not
initialize properly because the PCI resource space was not big enough.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds pcie node which is resposible for PCI-E x8 slot
functioning. Though, this was tested using only x1 SKY2 NIC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs
All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0. Changing pixel clock has no effect
on other fbs.
Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0
required command line parameters to preallocate memory for frame buffer diufb.
optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:
Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60
Bpp
bpp=32, bpp=24, or bpp=16
Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS
Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.
If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
virtex405-head.S is an assembler file, not a C file; therefore BOOTAFLAGS
is the correct place to set the needed -mcpu=405 flag.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds default NOR entries to the AMCC Canyonlands (460EX)
and Glacier (460GT) dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based adressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.
This code updates the ns16550 driver to use the reg-offset property
so that the Xilinx UART 16550 can be used with it. The reg-shift
was already being handled.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cleanups as suggested by Stephen Rothwell and Dale Farnsworth, which
incudes marking a bunch of functions static and add a vendor prefix to
the compat node check for uniqueness.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* remove #cpus from mpc8544ds.dts (not used anywhere else)
* remove memreserve from mpc8568mds.dts (not needed)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
