[ Upstream commit b08134eb254db56e9ce8170d9b82f0d7a616b6f8 ]
After initial start-up, the driver triggers ATI (calibration) with
the newly loaded register configuration in place. Next, the driver
polls a register field to ensure ATI completed in a timely fashion
and that the device is ready to sense.
However, communicating with the device over I2C while ATI is under-
way may induce noise in the device and cause ATI to fail. As such,
the vendor recommends not to poll the device during ATI.
To solve this problem, let the device naturally signal to the host
that ATI is complete by way of an interrupt. A completion prevents
the device from successfully probing until this happens.
As an added benefit, initial switch states are now reported in the
interrupt handler at the same time ATI status is checked. As such,
duplicate code that reports initial switch states has been removed
from iqs269_input_init().
The former logic that scaled ATI timeout and filter settling delay
is not carried forward with the new implementation, as it produces
overly conservative delays at the lower clock rate.
Rather, a single timeout that covers both clock rates is used. The
filter settling delay does not happen to be necessary and has been
removed as well.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7RtB2T7AF9rYMjK@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18ab69c8ca5678324efbeed874b707ce7b2feae1 ]
Polling the device while it transitions from automatic to manual
power mode switching may keep the device from actually finishing
the transition. The process appears to time out depending on the
polling rate and the device's core clock frequency.
This is ultimately unnecessary in the first place; instead it is
sufficient to write the desired mode during initialization, then
disable automatic switching at suspend. This eliminates the need
to ensure the device is prepared for a manual change and removes
the 'suspend_mode' variable.
Similarly, polling the device while it transitions from one mode
to another under manual control may time out as well. This added
step does not appear to be necessary either, so drop it.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs+eEXlRw4Vq57@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13f82ca3878db8284a70ef9711d7f710a31eb562 ]
Controllers that report pressure (e.g. ADS7846) use 5 commands and the
correct sequence is READ_X, READ_Y, READ_Z1, READ_Z2, PWRDOWN.
Controllers that don't report pressure (e.g. ADS7845/ADS7843) use only 3
commands and the correct sequence should be READ_X, READ_Y, PWRDOWN. But
the sequence sent was incorrect: READ_X, READ_Y, READ_Z1.
Fix this by setting the third (and last) command to PWRDOWN.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-3-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6965eece2a ]
Convert multiple full duplex transfers in to a single transfer to reduce
CPU load.
Current driver version support following filtering modes:
- ads7846_no_filter() - not filtered
- ads7846_debounce_filter() - driver specific debounce filter
- pdata->filter - platform specific debounce filter (do any platform
provides such filter?)
Without filter this HW is not really usable, since the physic of
resistive touchscreen can provide some bounce effects. With driver internal
filter, we have constant amount of retries + debounce retries if some anomaly
was detected.
High amount of tiny SPI transfers is the primer reason of high CPU load
and interrupt frequency.
This patch create one SPI transfer with all fields and not optional retires. If
bounce anomaly was detected, we will make more transfer if needed.
Without this patch, we will get about 10% CPU load on iMX6S on pen-down event.
For example by holding stylus on the screen.
With this patch, depending in the amount of retries, the CPU load will
be 1% with "ti,debounce-rep = <3>".
One buffer transfer allows us to use PIO FIFO or DMA engine, depending
on the platform.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-3-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 13f82ca3878d ("Input: ads7846 - always set last command to PWRDOWN")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c9509717b ]
Starting with 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845
controller support"), the ads7845 was partially converted to full duplex
mode.
Since it is not touchscreen controller specific, it is better to extend
this conversion to cover entire driver. This will reduce CPU load and make
driver more readable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-2-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 13f82ca3878d ("Input: ads7846 - always set last command to PWRDOWN")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3689abfc4e369a643d758a02fb9ad0b2403d6d6d ]
Unless it is being done as part of servicing a soft reset interrupt,
configuring channels on-the-fly (as is the case when writing to the
ati_trigger attribute) may cause GPIO3 (which reflects the state of
touch for a selected channel) to be inadvertently asserted.
To solve this problem, follow the vendor's recommendation and write
all channel configuration as well as the REDO_ATI register field as
part of a single block write. This ensures the device has been told
to re-calibrate itself following an I2C stop condition, after which
sensing resumes and GPIO3 may be asserted.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs8GyV7g0nF5Yy@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e023cc4abde3c01b895660b0e5a8488deb36b8c1 ]
The time the device takes to deassert its RDY output following an
I2C stop condition scales with the core clock frequency.
To prevent level-triggered interrupts from being reasserted after
the interrupt handler returns, increase the time before returning
to account for the worst-case delay (~140 us) plus margin.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs484ypy4dab5G@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59bc9cb3b80abaa42643abede0d5db8477901d9c ]
Each call to device/fwnode_get_named_child_node() must be matched
with a call to fwnode_handle_put() once the corresponding node is
no longer in use. This ensures a reference count remains balanced
in the case of dynamic device tree support.
Currently, the driver does not call fwnode_handle_put() on nested
event nodes. This patch solves this problem by adding the missing
instances of fwnode_handle_put().
As part of this change, the logic which parses each channel's key
code is gently refactored in order to reduce the number of places
from which fwnode_handle_put() is called.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/Y7Rsx68k/gvDVXAt@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6a87c3616 ]
A lot of modern Clevo barebones have touchpad and/or keyboard issues after
suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of them
have an external PS/2 port so this can safely be set for all of them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use. No negative effects could be
observed when setting all four.
The list is quite massive as neither the TUXEDO nor the Clevo dmi strings
have been very consistent historically. I tried to keep the list as short
as possible without risking on missing an affected device.
This is revision 3. The Clevo N150CU barebone is still removed as it might
have problems with the fix and needs further investigations. The
SchenkerTechnologiesGmbH System-/Board-Vendor string variations are
added. This is now based in the quirk table refactor. This now also
includes the additional noaux flag for the NS7xMU.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-5-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff946268a0 ]
Merge i8042 quirk tables to reduce code duplication for devices that need
more than one quirk. Before every quirk had its own table with devices
needing that quirk. If a new quirk needed to be added a new table had to
be created. When a device needed multiple quirks, it appeared in multiple
tables. Now only one table called i8042_dmi_quirk_table exists. In it every
device has one entry and required quirks are coded in the .driver_data
field of the struct dmi_system_id used by this table. Multiple quirks for
one device can be applied by bitwise-or of the new SERIO_QUIRK_* defines.
Also align quirkable options with command line parameters and make vendor
wide quirks per device overwriteable on a per device basis. The first match
is honored while following matches are ignored. So when a vendor wide quirk
is defined in the table, a device can inserted before and therefore
ignoring the vendor wide define.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-3-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a85fbd6498441694475716a4d5c65f9d3e073faf ]
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
Fixes: afe10358e4 ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e13757f524 ]
Like on the Acer Switch 10 SW5-012, the Acer Switch V 10 SW5-017's _LID
method messes with home- and power-button GPIO IRQ settings, causing an
IRQ storm.
Add a quirk entry for the Acer Switch V 10 to the dmi_use_low_level_irq[]
DMI quirk list, to use low-level IRQs on this model, fixing the IRQ storm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e9ada1d0e ]
It seems that the Windows drivers for the ACPI0011 soc_button_array
device use low level triggered IRQs rather then using edge triggering.
Some ACPI tables depend on this, directly poking the GPIO controller's
registers to clear the trigger type when closing a laptop's/2-in-1's lid
and re-instating the trigger when opening the lid again.
Linux sets the edge/level on which to trigger to both low+high since
it is using edge type IRQs, the ACPI tables then ends up also setting
the bit for level IRQs and since both low and high level have been
selected by Linux we get an IRQ storm leading to soft lockups.
As a workaround for this the soc_button_array already contains
a DMI quirk table with device models known to have this issue.
Add a module parameter for this so that users can easily test if their
device is affected too and so that they can use the module parameter
as a workaround.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e37cc624 ]
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a17b984115 upstream.
Suspending and resuming the system can sometimes cause the out
URB to get hung after a reset_resume. This causes LED setting
and force feedback to break on resume. To avoid this, just drop
the reset_resume callback so the USB core rebinds xpad to the
wireless pads on resume if a reset happened.
A nice side effect of this change is the LED ring on wireless
controllers is now set correctly on system resume.
Cc: stable@vger.kernel.org
Fixes: 4220f7db1e ("Input: xpad - workaround dead irq_out after suspend/ resume")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Link: https://lore.kernel.org/r/20220818154411.510308-3-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
