[ Upstream commit 5ac121b81b ]
The AXP288's recommended and factory default Vhold value (minimum
input voltage below which the input current draw will be reduced)
is 4.4V. This lines up with other charger IC's such as the TI
bq2419x/bq2429x series which use 4.36V or 4.44V.
For some reason some BIOS-es initialize Vhold to 4.6V or even 4.7V
which combined with the typical voltage drop over typically low
wire gauge micro-USB cables leads to the input-current getting
capped below 1A (with a 2A capable dedicated charger) based on Vhold.
This leads to slow charging, or even to the device slowly discharging
if the device is in heavy use.
As the Linux AXP288 drivers use the builtin BC1.2 charger detection
and send the input-current-limit according to the detected charger
there really is no reason not to use the recommended 4.4V Vhold.
Set Vhold to 4.4V to fix the slow charging issue on various devices.
There is one exception, the special-case of the HP X2 2-in-1s which
combine this BC1.2 capable PMIC with a Type-C port and a 5V/3A factory
provided charger with a Type-C plug which does not do BC1.2. These
have their input-current-limit hardcoded to 3A (like under Windows)
and use a higher Vhold on purpose to limit the current when used
with other chargers. To avoid touching Vhold on these HP X2 laptops
the code setting Vhold is added to an else branch of the if checking
for these models.
Note this also fixes the sofar unused VBUS_ISPOUT_VHOLD_SET_MASK
define, which was wrong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4f408cdcd ]
As stated in [1], negative current values are used for discharging
batteries.
AXP PMICs internally have two different ADC channels for shunt current
measurement: one used during charging and one during discharging.
The values reported by these ADCs are unsigned.
While the driver properly selects ADC channel to get the data from,
it doesn't apply negative sign when reporting discharging current.
[1] Documentation/ABI/testing/sysfs-class-power
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b14b5ba1 ]
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid same code.
Fixes: 14431aa0c5 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7731754fd ]
The datasheet says that the BQ24190_REG_POC_CHG_CONFIG bits can
have a value of either 10(0x2) or 11(0x3) for OTG (5V boost regulator)
mode.
Sofar bq24190_vbus_is_enabled() was only checking for 10 but some BIOS-es
uses 11 when enabling the regulator at boot.
Make bq24190_vbus_is_enabled() also check for 11 so that it does not
wrongly returns false when the bits are set to 11.
Fixes: 66b6bef2c4 ("power: supply: bq24190_charger: Export 5V boost converter as regulator")
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a4760463d ]
kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Fix memory leak by calling kobject_put().
Fixes: 8c0984e5a7 ("power: move power supply drivers to power/supply")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba18dad0fb ]
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c1348bf05 ]
The return value of platform_get_resource() needs to be checked.
To avoid use of error pointer in case that there is no suitable
resource.
Fixes: d28c74c107 ("power: reset: add driver for mt6323 poweroff")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 80211be1b9 upstream.
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 644106cdb8 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
Fixes: 6647156c00 ("power: reset: add LTC2952 poweroff driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cdf10ffe8f ]
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c097 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0cf48167b8 upstream.
The gauge requires us to clear the status bits manually for some alerts
to be properly dismissed. Previously the IRQ was configured to react only
on falling edge, which wasn't technically correct (the ALRT line is active
low), but it had a happy side-effect of preventing interrupt storms
on uncleared alerts from happening.
Fixes: 7fbf6b731b ("power: supply: max17042: Do not enforce (incorrect) interrupt trigger type")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223a3b8283 upstream.
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b1 ("power_supply: Add MAX17042 Fuel Gauge Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54784ffa5b upstream.
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad1abe4769 ]
Deal with deferred probe using dev_err_probe so the error is handled
and avoid logging lots probe defer information like the following:
[ 9.125121] cw2015 4-0062: Failed to register power supply
[ 9.211131] cw2015 4-0062: Failed to register power supply
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efe2175478 ]
Pin control needs to be activated by setting the enable bit, otherwise
hardware rejects all pin changes. Previously this stayed unnoticed on
Nexus 7 because pin control was enabled by default after rebooting from
downstream kernel, which uses driver that enables the bit and charger
registers are non-volatile until power supply (battery) is disconnected.
Configure the pin control enable bit. This fixes the potentially
never-enabled charging on devices that use pin control.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caa534c3ba ]
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3076cd8d1 ]
The fuel gauge in the RT5033 PMIC has its own I2C bus and interrupt
line. Therefore, it is not actually part of the RT5033 MFD and needs
its own of_match_table to probe properly.
Also, given that it's independent of the MFD, there is actually
no need to make the Kconfig depend on MFD_RT5033. Although the driver
uses the shared <linux/mfd/rt5033.h> header, there is no compile
or runtime dependency on the RT5033 MFD driver.
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Fixes: b847dd96e6 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfe52db13a ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 073b5d5b1f ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
