The 7278 device is the first device that includes support for the V7
memory map developed for use in 64-bit architecture brcmstb devices.
This map relocates the register physical offset from 0xF0000000 to
0x0000000008000000.
Since the ARM PERIPHBASE value is also relocated in the V7 memory map
we can use its value to determine whether this device uses the new
V7 memory map and therefore where to look for the SUN_TOP_CTRL
register used to identify the chip family.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building a big-endian kernel for ARCH_BRCMSTB revealed that we would not
be correctly polling for the right bit in the busyuart macro, turns out
there are a few transformations needed to work with big-endian kernels.
First we need to swap the value we read from SUN_TOP_CTRL to properly
compare it against our local tables. Then, just like 8250.S we need to
swap the value before storing it, and conversely swap it after a load.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pull ARM updates from Russell King:
"Low priority fixes and updates for ARM:
- add some missing includes
- efficiency improvements in system call entry code when tracing is
enabled
- ensure ARMv6+ is always built as EABI
- export save_stack_trace_tsk()
- fix fatal signal handling during mm fault
- build translation table base address register from scratch
- appropriately align the .data section to a word boundary where we
rely on that data being word aligned"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8691/1: Export save_stack_trace_tsk()
ARM: 8692/1: mm: abort uaccess retries upon fatal signal
ARM: 8690/1: lpae: build TTB control register value from scratch in v7_ttb_setup
ARM: align .data section
ARM: always enable AEABI for ARMv6+
ARM: avoid saving and restoring registers unnecessarily
ARM: move PC value into r9
ARM: obtain thread info structure later
ARM: use aliases for registers in entry-common
ARM: 8689/1: scu: add missing errno include
ARM: 8688/1: pm: add missing types include
Robert Jarzmik reports that his PXA25x system fails to boot with 4.12,
failing at __flush_whole_cache in arch/arm/mm/proc-xscale.S:215:
0xc0019e20 <+0>: ldr r1, [pc, #788]
0xc0019e24 <+4>: ldr r0, [r1] <== here
with r1 containing 0xc06f82cd, which is the address of "clean_addr".
Examination of the System.map shows:
c06f22c8 D user_pmd_table
c06f22cc d __warned.19178
c06f22cd d clean_addr
indicating that a .data.unlikely section has appeared just before the
.data section from proc-xscale.S. According to objdump -h, it appears
that our assembly files default their .data alignment to 2**0, which
is bad news if the preceding .data section size is not power-of-2
aligned at link time.
Add the appropriate .align directives to all assembly files in arch/arm
that are missing them where we require an appropriate alignment.
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <hoeun.ryu@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <hoeun.ryu@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <hoeun.ryu@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <hoeun.ryu@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BCM7260 has the same UART base address as 7268, order the entries by
ascending chip number and alias the 7268 definition to the 7260
definition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The SUN_TOP_CTRL_FAMILY_ID register is at a fixed absolute address for
all of our supported chips, so utilize its value to determine what the
UARTA base address should be based on the value we read.
Since the code is called both during decompressor when the MMU is off,
and after the MMU has been turned on in the kernel, and we want to do
the lookup only once, we use the same technique as tegra.S and have a
shared storage location between the decompressor and the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Last CLPS711X CPU register is PLLR has 0xa5a8 address, so we can reduce
the map to 48k and align the end of the static at VMALLOC_START.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Exynos542x SoCs using A15+A7 can boot to A15 or A7. If it boots using
A7 (like on Odroid XU family boards), it can't choose right UART
physical address only the part number of CP15. Fix the detection logic
by checking the Cluster ID additionally.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
[k.kozlowski: Extend commit message]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The exynos low-level debug macros need to be fixed if the system is being
built big endian. Add the necessary endian swaps for accessing the registers
to get output working again
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
AT91 still uses an offset (0x0100 0000) from the physical address to map
the debug UART. This is unfortunate as for some platforms (sama5d3 and
earlier), it ends up in the PCI zone and PCI is enabled in multi_v7.
Switch to DEBUG_UART_VIRT to solve that.
Tested on sama5d3 and 9g20.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Merge "i.MX SoC update for 4.6" from Shawn Guo:
- Enable big endian mode support for i.MX platform
- Add support for i.MX6QP SoC which is the latest i.MX6 family addition
- Add basic suspend/resume support for i.MX25
- A couple of i.MX7D support updates
- A few random code cleanups
* tag 'imx-soc-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
ARM: mx25: Add basic suspend/resume support
ARM: imx: Add msl code support for imx6qp
ARM: imx: enable big endian mode
ARM: imx: use endian-safe readl/readw/writel/writew
ARM: imx7d: correct chip version information
ARM: imx: select HAVE_ARM_ARCH_TIMER if selected i.MX7D
ARM: imx6: fix cleanup path in imx6q_suspend_init()
In an invalid randconfig build (fixed by another patch),
I ran across this warning:
arch/arm/include/debug/at91.S:18:0: error: "CONFIG_DEBUG_UART_VIRT" redefined [-Werror]
#define CONFIG_DEBUG_UART_VIRT AT91_IO_P2V(CONFIG_DEBUG_UART_PHYS)
As Russell pointed out, we should never #define a macro starting
with CONFIG_ in a source file, as that is rather confusing.
This renames the macro to avoid the symbol clash.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Merge "ARM: Xilinx Zynq patches for v4.6" from Michal Simek:
- SLCR early init
- Fix L2 cache data corruption
- Fix early printk uart setting
* tag 'zynq-soc-for-4.6' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: zynq: address L2 cache data corruption
ARM: zynq: initialize slcr mapping earlier
The patch
"ARM: 8432/1: move VMALLOC_END from 0xff000000 to 0xff800000"
(sha1: 6ff0966052)
has moved also start of VMALLOC area because size didn't change.
That's why origin location of vmalloc was
vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
and now is
vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
That's why uart virtual addresses need to be changed to reflect this new
memory setup. Starting address should be vmalloc start address.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Some SoCs use a Palmchip BK-310x UART which is mostly 16550 compatible
but with a different register layout. While this UART has previously
only been supported in MIPS based chips (Alchemy, Ralink), the ARM based
SMP87xx series from Sigma Designs also uses it.
This patch allows the debug console to work with this type of UART.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable ARM big-endian mode on mach-imx. This requires adding some
byte swapping in the debug functions (which otherwise hang forever)
and of course the secondary core bringup.
Tested (on top of 4.4) on i.MX6 HummingBoard quad-core (IMX6Q).
The patch is pretty much as suggested by Arnd Bergmann, thanks!
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Footbridge has two debug ports that are handled a bit differently:
The 8250 port uses the normal debug/8250.S implementation that is shared
with a lot of other platforms, but it relies on the DEBUG_UART_8250
option to be turned on automatically instead of being selected by
DEBUG_FOOTBRIDGE_COM1 as we do for most other platforms. I'm changing
this to use a 'select' and change the dependency to the debug symbol
rather than the platform symbol for consistency.
The DC21285 UART has a separate top-level option, and relies on
the traditional include/mach/debug-macro.S method. With the s3c64xx
multiplatform series queued up for 4.5, it is now the last one that does
this, so by moving this file to include/debug/dc21285.S, we can get
all platforms to do things the same way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
