[ Upstream commit bc923d594db21bee0ead128eb4bb78f7e77467a4 ]
There is a small window in ssam_serial_hub_probe() where the controller
is initialized but has not been started yet. Specifically, between
ssam_controller_init() and ssam_controller_start(). Any failure in this
window, for example caused by a failure of serdev_device_open(),
currently results in an incorrect warning being emitted.
In particular, any failure in this window results in the controller
being destroyed via ssam_controller_destroy(). This function checks the
state of the controller and, in an attempt to validate that the
controller has been cleanly shut down before we try and deallocate any
resources, emits a warning if that state is not SSAM_CONTROLLER_STOPPED.
However, since we have only just initialized the controller and have not
yet started it, its state is SSAM_CONTROLLER_INITIALIZED. Note that this
is the only point at which the controller has this state, as it will
change after we start the controller with ssam_controller_start() and
never revert back. Further, at this point no communication has taken
place and the sender and receiver threads have not been started yet (and
we may not even have an open serdev device either).
Therefore, it is perfectly safe to call ssam_controller_destroy() with a
state of SSAM_CONTROLLER_INITIALIZED. This, however, means that the
warning currently being emitted is incorrect. Fix it by extending the
check.
Fixes: c167b9c7e3 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240811124645.246016-1-luzmaximilian@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe0e04cf66a12ffe6d1b43725ddaabd5599d024f upstream.
If platform_profile_register() fails, the driver does not propagate
the error, but instead probes successfully. This means when the driver
unbinds, the a warning might be issued by platform_profile_remove().
Fix this by propagating the error back to the caller of
surface_platform_profile_probe().
Compile-tested only.
Fixes: b78b4982d7 ("platform/surface: Add platform profile driver")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20231014235449.288702-1-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bed667033e66083d363a11e9414ad401ecc242c ]
Devices with a type-cover have an additional "book" mode, deactivating
type-cover input and turning off its backlight. This is currently
unsupported, leading to the warning
surface_aggregator_tablet_mode_switch 01:0e:01:00:01: unknown KIP cover state: 6
Therefore, add support for this state and map it to enable tablet-mode.
Fixes: 9f794056db ("platform/surface: Add KIP/POS tablet-mode switch driver")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20230525213218.2797480-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 539e0a7f9105d19c00629c3f4da00330488e8c60 ]
Currently, event completion work-items are restricted to be run strictly
in non-parallel fashion by the respective workqueue. However, this has
lead to some problems:
In some instances, the event notifier function called inside this
completion workqueue takes a non-negligible amount of time to execute.
One such example is the battery event handling code (surface_battery.c),
which can result in a full battery information refresh, involving
further synchronous communication with the EC inside the event handler.
This is made worse if the communication fails spuriously, generally
incurring a multi-second timeout.
Since the event completions are run strictly non-parallel, this blocks
other events from being propagated to the respective subsystems. This
becomes especially noticeable for keyboard and touchpad input, which
also funnel their events through this system. Here, users have reported
occasional multi-second "freezes".
Note, however, that the event handling system was never intended to run
purely sequentially. Instead, we have one work struct per EC/SAM
subsystem, processing the event queue for that subsystem. These work
structs were intended to run in parallel, allowing sequential processing
of work items for each subsystem but parallel processing of work items
across subsystems.
The only restriction to this is the way the workqueue is created.
Therefore, replace create_workqueue() with alloc_workqueue() and do not
restrict the maximum number of parallel work items to be executed on
that queue, resolving any cross-subsystem blockage.
Fixes: c167b9c7e3 ("platform/surface: Add Surface Aggregator subsystem")
Link: https://github.com/linux-surface/linux-surface/issues/1026
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20230525210110.2785470-1-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ae0fa0a3126a86c801c3220fcd8eefe03aa39f3e upstream.
It is possible that we (the host/kernel driver) receive command messages
that are not intended for us. Ignore those for now.
The whole story is a bit more complicated: It is possible to enable
debug output on SAM, which is sent via SSH command messages. By default
this output is sent to a debug connector, with its own target ID
(TID=0x03). It is possible to override the target of the debug output
and set it to the host/kernel driver. This, however, does not change the
original target ID of the message. Meaning, we receive messages with
TID=0x03 (debug) but expect to only receive messages with TID=0x00
(host).
The problem is that the different target ID also comes with a different
scope of request IDs. In particular, these do not follow the standard
event rules (i.e. do not fall into a set of small reserved values).
Therefore, current message handling interprets them as responses to
pending requests and tries to match them up via the request ID. However,
these debug output messages are not in fact responses, and therefore
this will at best fail to find the request and at worst pass on the
wrong data as response for a request.
Therefore ignore any command messages not intended for us (host) for
now. We can implement support for the debug messages once we have a
better understanding of them.
Note that this may also provide a bit more stability and avoid some
driver confusion in case any other targets want to talk to us in the
future, since we don't yet know what to do with those as well. A warning
for the dropped messages should suffice for now and also give us a
chance of discovering new targets if they come along without any
potential for bugs/instabilities.
Fixes: c167b9c7e3 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221202223327.690880-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal and type-cover HID devices
(including sensors, touchpad, keyboard, and other miscellaneous devices)
on the Surface Pro 9.
This does not include support for a tablet-mode switch yet, as that is
now handled via the POS subsystem (unlike the Surface Pro 8, where it is
handled via the KIP subsystem) and therefore needs further changes.
While we're at it, also add the missing comment for the Surface Pro 8.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently, we check any received packet whether we have already seen it
previously, regardless of the packet type (sequenced / unsequenced). We
do this by checking the sequence number. This assumes that sequence
numbers are valid for both sequenced and unsequenced packets. However,
this assumption appears to be incorrect.
On some devices, the sequence number field of unsequenced packets (in
particular HID input events on the Surface Pro 9) is always zero. As a
result, the current retransmission check kicks in and discards all but
the first unsequenced packet, breaking (among other things) keyboard and
touchpad input.
Note that we have, so far, only seen packets being retransmitted in
sequenced communication. In particular, this happens when there is an
ACK timeout, causing the EC (or us) to re-send the packet waiting for an
ACK. Arguably, retransmission / duplication of unsequenced packets
should not be an issue as there is no logical condition (such as an ACK
timeout) to determine when a packet should be sent again.
Therefore, remove the retransmission check for unsequenced packets
entirely to resolve the issue.
Fixes: c167b9c7e3 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-1-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Pull x86 platform driver updates from Hans de Goede:
- AMD Platform Management Framework (PMF) driver with AMT and QnQF
support
- AMD PMC: Improved logging for debugging s2idle issues
- Big refactor of the ACPI/x86 backlight handling, ensuring that we
only register 1 /sys/class/backlight device per LCD panel
- Microsoft Surface:
- Surface Laptop Go 2 support
- Surface Pro 8 HID sensor support
- Asus WMI:
- Lots of cleanups
- Support for TUF RGB keyboard backlight control
- Add support for ROG X13 tablet mode
- Siemens Simatic: IPC227G and IPC427G support
- Toshiba ACPI laptop driver: Fan hwmon and battery ECO mode support
- tools/power/x86/intel-speed-select: Various improvements
- Various cleanups
- Various small bugfixes
* tag 'platform-drivers-x86-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (153 commits)
platform/x86: use PLATFORM_DEVID_NONE instead of -1
platform/x86/amd: pmc: Dump idle mask during "check" stage instead
platform/x86/intel/wmi: thunderbolt: Use dev_groups callback
platform/x86/amd: pmc: remove CONFIG_DEBUG_FS checks
platform/surface: Split memcpy() of struct ssam_event flexible array
platform/x86: compal-laptop: Get rid of a few forward declarations
platform/x86: intel-uncore-freq: Use sysfs_emit() to instead of scnprintf()
platform/x86: dell-smbios-base: Use sysfs_emit()
platform/x86/amd/pmf: Remove unused power_delta instances
platform/x86/amd/pmf: install notify handler after acpi init
Documentation/ABI/testing/sysfs-amd-pmf: Add ABI doc for AMD PMF
platform/x86/amd/pmf: Add sysfs to toggle CnQF
platform/x86/amd/pmf: Add support for CnQF
platform/x86/amd: pmc: Fix build without debugfs
platform/x86: hp-wmi: Support touchpad on/off
platform/x86: int3472/discrete: Drop a forward declaration
platform/x86: toshiba_acpi: change turn_on_panel_on_resume to static
platform/x86: wmi: Drop forward declaration of static functions
platform/x86: toshiba_acpi: Remove duplicate include
platform/x86: msi-laptop: Change DMI match / alias strings to fix module autoloading
...
Add software nodes for the HID sensor collection and the UCM UCSI HID
client to the Surface Pro 8. In contrast to the type-cover devices,
these devices are directly attached to the SAM controller, without any
hub.
This enables support for HID-based sensors, including the ones used for
automatic screen rotation, on the Surface Pro 8.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20220810144117.493710-4-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add software nodes for the HID sensor collection and the UCM UCSI HID
client to the Surface Pro 8. In contrast to the type-cover devices,
these devices are directly attached to the SAM controller, without any
hub.
This enables support for HID-based sensors, including the ones used for
automatic screen rotation, on the Surface Pro 8.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20220810144117.493710-4-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
