commit 38762a0763c10c24a4915feee722d7aa6e73eb98 upstream.
Ensure that packet_buffer_get respects the user_length provided. If
the length of the head packet exceeds the user_length, packet_buffer_get
will now return 0 to signify to the user that no data were read
and a larger buffer size is required. Helps prevent user space overflows.
Signed-off-by: Thanassis Avgerinos <thanassis.avgerinos@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 752e3c53de0fa3b7d817a83050b6699b8e9c6ec9 ]
In the FireWire OHCI interrupt handler, if a bus reset interrupt has
occurred, mask bus reset interrupts until bus_reset_work has serviced and
cleared the interrupt.
Normally, we always leave bus reset interrupts masked. We infer the bus
reset from the self-ID interrupt that happens shortly thereafter. A
scenario where we unmask bus reset interrupts was introduced in 2008 in
a007bb857e: If
OHCI_PARAM_DEBUG_BUSRESETS (8) is set in the debug parameter bitmask, we
will unmask bus reset interrupts so we can log them.
irq_handler logs the bus reset interrupt. However, we can't clear the bus
reset event flag in irq_handler, because we won't service the event until
later. irq_handler exits with the event flag still set. If the
corresponding interrupt is still unmasked, the first bus reset will
usually freeze the system due to irq_handler being called again each
time it exits. This freeze can be reproduced by loading firewire_ohci
with "modprobe firewire_ohci debug=-1" (to enable all debugging output).
Apparently there are also some cases where bus_reset_work will get called
soon enough to clear the event, and operation will continue normally.
This freeze was first reported a few months after a007bb85 was committed,
but until now it was never fixed. The debug level could safely be set
to -1 through sysfs after the module was loaded, but this would be
ineffectual in logging bus reset interrupts since they were only
unmasked during initialization.
irq_handler will now leave the event flag set but mask bus reset
interrupts, so irq_handler won't be called again and there will be no
freeze. If OHCI_PARAM_DEBUG_BUSRESETS is enabled, bus_reset_work will
unmask the interrupt after servicing the event, so future interrupts
will be caught as desired.
As a side effect to this change, OHCI_PARAM_DEBUG_BUSRESETS can now be
enabled through sysfs in addition to during initial module loading.
However, when enabled through sysfs, logging of bus reset interrupts will
be effective only starting with the second bus reset, after
bus_reset_work has executed.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0b06dc48fb15902d7da09c5c0861e7f042a9381 ]
When resetting the bus after a gap count error, use a long rather than
short bus reset.
IEEE 1394-1995 uses only long bus resets. IEEE 1394a adds the option of
short bus resets. When video or audio transmission is in progress and a
device is hot-plugged elsewhere on the bus, the resulting bus reset can
cause video frame drops or audio dropouts. Short bus resets reduce or
eliminate this problem. Accordingly, short bus resets are almost always
preferred.
However, on a mixed 1394/1394a bus, a short bus reset can trigger an
immediate additional bus reset. This double bus reset can be interpreted
differently by different nodes on the bus, resulting in an inconsistent gap
count after the bus reset. An inconsistent gap count will cause another bus
reset, leading to a neverending bus reset loop. This only happens for some
bus topologies, not for all mixed 1394/1394a buses.
By instead sending a long bus reset after a gap count inconsistency, we
avoid the doubled bus reset, restoring the bus to normal operation.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Link: https://sourceforge.net/p/linux1394/mailman/message/58741624/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ed4380009e96d9e9c605e12822e987b35b05648 ]
If we are bus manager and the bus has inconsistent gap counts, send a
bus reset immediately instead of trying to read the root node's config
ROM first. Otherwise, we could spend a lot of time trying to read the
config ROM but never succeeding.
This eliminates a 50+ second delay before the FireWire bus is usable after
a newly connected device is powered on in certain circumstances.
The delay occurs if a gap count inconsistency occurs, we are not the root
node, and we become bus manager. One scenario that causes this is with a TI
XIO2213B OHCI, the first time a Sony DSR-25 is powered on after being
connected to the FireWire cable. In this configuration, the Linux box will
not receive the initial PHY configuration packet sent by the DSR-25 as IRM,
resulting in the DSR-25 having a gap count of 44 while the Linux box has a
gap count of 63.
FireWire devices have a gap count parameter, which is set to 63 on power-up
and can be changed with a PHY configuration packet. This determines the
duration of the subaction and arbitration gaps. For reliable communication,
all nodes on a FireWire bus must have the same gap count.
A node may have zero or more of the following roles: root node, bus manager
(BM), isochronous resource manager (IRM), and cycle master. Unless a root
node was forced with a PHY configuration packet, any node might become root
node after a bus reset. Only the root node can become cycle master. If the
root node is not cycle master capable, the BM or IRM should force a change
of root node.
After a bus reset, each node sends a self-ID packet, which contains its
current gap count. A single bus reset does not change the gap count, but
two bus resets in a row will set the gap count to 63. Because a consistent
gap count is required for reliable communication, IEEE 1394a-2000 requires
that the bus manager generate a bus reset if it detects that the gap count
is inconsistent.
When the gap count is inconsistent, build_tree() will notice this after the
self identification process. It will set card->gap_count to the invalid
value 0. If we become bus master, this will force bm_work() to send a bus
reset when it performs gap count optimization.
After a bus reset, there is no bus manager. We will almost always try to
become bus manager. Once we become bus manager, we will first determine
whether the root node is cycle master capable. Then, we will determine if
the gap count should be changed. If either the root node or the gap count
should be changed, we will generate a bus reset.
To determine if the root node is cycle master capable, we read its
configuration ROM. bm_work() will wait until we have finished trying to
read the configuration ROM.
However, an inconsistent gap count can make this take a long time.
read_config_rom() will read the first few quadlets from the config ROM. Due
to the gap count inconsistency, eventually one of the reads will time out.
When read_config_rom() fails, fw_device_init() calls it again until
MAX_RETRIES is reached. This takes 50+ seconds.
Once we give up trying to read the configuration ROM, bm_work() will wake
up, assume that the root node is not cycle master capable, and do a bus
reset. Hopefully, this will resolve the gap count inconsistency.
This change makes bm_work() check for an inconsistent gap count before
waiting for the root node's configuration ROM. If the gap count is
inconsistent, bm_work() will immediately do a bus reset. This eliminates
the 50+ second delay and rapidly brings the bus to a working state.
I considered that if the gap count is inconsistent, a PHY configuration
packet might not be successful, so it could be desirable to skip the PHY
configuration packet before the bus reset in this case. However, IEEE
1394a-2000 and IEEE 1394-2008 say that the bus manager may transmit a PHY
configuration packet before a bus reset when correcting a gap count error.
Since the standard endorses this, I decided it's safe to retain the PHY
configuration packet transmission.
Normally, after a topology change, we will reset the bus a maximum of 5
times to change the root node and perform gap count optimization. However,
if there is a gap count inconsistency, we must always generate a bus reset.
Otherwise the gap count inconsistency will persist and communication will
be unreliable. For that reason, if there is a gap count inconstency, we
generate a bus reset even if we already reached the 5 reset limit.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Reference: https://sourceforge.net/p/linux1394/mailman/message/58727806/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ac9184fbb8478dab4a0724b279f94956b69be827 upstream.
VIA VT6306/6307/6308 provides PCI interface compliant to 1394 OHCI. When
the hardware is combined with Asmedia ASM1083/1085 PCIe-to-PCI bus bridge,
it appears that accesses to its 'Isochronous Cycle Timer' register (offset
0xf0 on PCI memory space) often causes unexpected system reboot in any
type of AMD Ryzen machine (both 0x17 and 0x19 families). It does not
appears in the other type of machine (AMD pre-Ryzen machine, Intel
machine, at least), or in the other OHCI 1394 hardware (e.g. Texas
Instruments).
The issue explicitly appears at a commit dcadfd7f7c74 ("firewire: core:
use union for callback of transaction completion") added to v6.5 kernel.
It changed 1394 OHCI driver to access to the register every time to
dispatch local asynchronous transaction. However, the issue exists in
older version of kernel as long as it runs in AMD Ryzen machine, since
the access to the register is required to maintain bus time. It is not
hard to imagine that users experience the unexpected system reboot when
generating bus reset by plugging any devices in, or reading the register
by time-aware application programs; e.g. audio sample processing.
This commit suppresses the unexpected system reboot in the combination of
hardware. It avoids the access itself. As a result, the software stack can
not provide the hardware time anymore to unit drivers, userspace
applications, and nodes in the same IEEE 1394 bus. It brings apparent
disadvantage since time-aware application programs require it, while
time-unaware applications are available again; e.g. sbp2.
Cc: stable@vger.kernel.org
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://bugzilla.suse.com/show_bug.cgi?id=1215436
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217994
Reported-by: Tobias Gruetzmacher <tobias-lists@23.gs>
Closes: https://sourceforge.net/p/linux1394/mailman/message/58711901/
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2240973
Closes: https://bugs.launchpad.net/linux/+bug/2043905
Link: https://lore.kernel.org/r/20240102110150.244475-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6371be7aeb986905bb60ec73d002fc02343393b4 upstream.
Commit 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop
management") changed the single bit manage_start_stop flag into 2 boolean
fields of the SCSI device structure. Commit 24eca2dce0f8 ("scsi: sd:
Introduce manage_shutdown device flag") introduced the manage_shutdown
boolean field for the same structure. Together, these 2 commits increase
the size of struct scsi_device by 8 bytes by using booleans instead of
defining the manage_xxx fields as single bit flags, similarly to other
flags of this structure.
Avoid this unnecessary structure size increase and be consistent with the
definition of other flags by reverting the definitions of the manage_xxx
fields as single bit flags.
Fixes: 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop management")
Fixes: 24eca2dce0f8 ("scsi: sd: Introduce manage_shutdown device flag")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231120225631.37938-2-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 891e0eab32a57fca4d36c5162628eb0bcb1f0edf upstream.
If device_register() fails, the refcount of device is not 0, the name
allocated in dev_set_name() is leaked. To fix this by calling put_device(),
so that it will be freed in callback function kobject_cleanup().
unreferenced object 0xffff9d99035c7a90 (size 8):
comm "systemd-udevd", pid 168, jiffies 4294672386 (age 152.089s)
hex dump (first 8 bytes):
66 77 30 2e 30 00 ff ff fw0.0...
backtrace:
[<00000000e1d62bac>] __kmem_cache_alloc_node+0x1e9/0x360
[<00000000bbeaff31>] __kmalloc_node_track_caller+0x44/0x1a0
[<00000000491f2fb4>] kvasprintf+0x67/0xd0
[<000000005b960ddc>] kobject_set_name_vargs+0x1e/0x90
[<00000000427ac591>] dev_set_name+0x4e/0x70
[<000000003b4e447d>] create_units+0xc5/0x110
fw_unit_release() will be called in the error path, move fw_device_get()
before calling device_register() to keep balanced with fw_device_put() in
fw_unit_release().
Cc: stable@vger.kernel.org
Fixes: 1fa5ae857b ("driver core: get rid of struct device's bus_id string array")
Fixes: a1f64819fe ("firewire: struct device - replace bus_id with dev_name(), dev_set_name()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24eca2dce0f8d19db808c972b0281298d0bafe99 upstream.
Commit aa3998dbeb3a ("ata: libata-scsi: Disable scsi device
manage_system_start_stop") change setting the manage_system_start_stop
flag to false for libata managed disks to enable libata internal
management of disk suspend/resume. However, a side effect of this change
is that on system shutdown, disks are no longer being stopped (set to
standby mode with the heads unloaded). While this is not a critical
issue, this unclean shutdown is not recommended and shows up with
increased smart counters (e.g. the unexpected power loss counter
"Unexpect_Power_Loss_Ct").
Instead of defining a shutdown driver method for all ATA adapter
drivers (not all of them define that operation), this patch resolves
this issue by further refining the sd driver start/stop control of disks
using the new flag manage_shutdown. If this new flag is set to true by
a low level driver, the function sd_shutdown() will issue a
START STOP UNIT command with the start argument set to 0 when a disk
needs to be powered off (suspended) on system power off, that is, when
system_state is equal to SYSTEM_POWER_OFF.
Similarly to the other manage_xxx flags, the new manage_shutdown flag is
exposed through sysfs as a read-write device attribute.
To avoid any confusion between manage_shutdown and
manage_system_start_stop, the comments describing these flags in
include/scsi/scsi.h are also improved.
Fixes: aa3998dbeb3a ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218038
Link: https://lore.kernel.org/all/cd397c88-bf53-4768-9ab8-9d107df9e613@gmail.com/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3cc2ffe5c16dc65dfac354bc5b5bc98d3b397567 ]
The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.
For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.
Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 99398d2070ab ("scsi: sd: Do not issue commands to suspended disks on shutdown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 531390a243ef47448f8bad01c186c2787666bf4d upstream.
This patch is fix for Linux kernel v2.6.33 or later.
For request subaction to IEC 61883-1 FCP region, Linux FireWire subsystem
have had an issue of use-after-free. The subsystem allows multiple
user space listeners to the region, while data of the payload was likely
released before the listeners execute read(2) to access to it for copying
to user space.
The issue was fixed by a commit 281e20323a ("firewire: core: fix
use-after-free regression in FCP handler"). The object of payload is
duplicated in kernel space for each listener. When the listener executes
ioctl(2) with FW_CDEV_IOC_SEND_RESPONSE request, the object is going to
be released.
However, it causes memory leak since the commit relies on call of
release_request() in drivers/firewire/core-cdev.c. Against the
expectation, the function is never called due to the design of
release_client_resource(). The function delegates release task
to caller when called with non-NULL fourth argument. The implementation
of ioctl_send_response() is the case. It should release the object
explicitly.
This commit fixes the bug.
Cc: <stable@vger.kernel.org>
Fixes: 281e20323a ("firewire: core: fix use-after-free regression in FCP handler")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20230117090610.93792-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
card->local_node and card->bm_retries are both always accessed under
card->lock.
fw_core_handle_bus_reset has a check whose condition depends on
card->local_node and whose body writes to card->bm_retries.
Both of these accesses are not under card->lock. Move the lock acquiring
of card->lock to before this check such that these accesses do happen
when card->lock is held.
fw_destroy_nodes is called inside the check.
Since fw_destroy_nodes already acquires card->lock inside its function
body, move this out to the callsites of fw_destroy_nodes.
Also add a comment to indicate which locking is necessary when calling
fw_destroy_nodes.
Cc: <stable@vger.kernel.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In 1394 OHCI specification, descriptor of Asynchronous Receive DMA context
has timeStamp field in its trailer quadlet. The field is written by
the host controller for the time to receive asynchronous request
subaction in isochronous cycle time.
In Linux FireWire subsystem, the value of field is stored to fw_packet
structure and copied to fw_request structure as the part. The fw_request
structure is hidden from unit driver and passed as opaque pointer when
calling registered handler. It's inconvenient to the unit driver which
needs timestamp of packet.
This commit adds kernel API to pick up timestamp from opaque pointer to
fw_request structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220405072221.226217-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
1394 OHCI specification defined Isochronous Cycle Timer Register to get
value of CYCLE_TIME register defined by IEEE 1394 for CSR architecture
defined by ISO/IEC 13213. Unit driver can calculate packet time by
compute with the value of CYCLE_TIME and timeStamp field in descriptor
of each isochronous and asynchronous context. The resolution of CYCLE_TIME
is 49.576 MHz, while the one of timeStamp is 8,000 Hz.
Current implementation of Linux FireWire subsystem allows the driver to
get the value of CYCLE_TIMER CSR register by transaction service. The
transaction service has overhead in regard of access to MMIO register.
This commit adds kernel API for unit driver to access the register
directly.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220405072221.226217-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Hector Martin wrote)
This fixes segfaults when a card gets yanked off of the PCIe bus while
busy, e.g. with a userspace app trying to get the cycle time:
[8638860.994310] Call Trace:
[8638860.994313] ioctl_get_cycle_timer2+0x4f/0xd0 [firewire_core]
[8638860.994323] fw_device_op_ioctl+0xae/0x150 [firewire_core]
[8638860.994328] __x64_sys_ioctl+0x7d/0xb0
[8638860.994332] do_syscall_64+0x45/0x80
[8638860.994337] entry_SYSCALL_64_after_hwframe+0x44/0xae
(Takashi Sakamoto wrote)
As long as reading commit 2080222429 ("firewire: core: add forgotten
dummy driver methods, remove unused ones"), three functions are not
implemeted in dummy driver for reason; .read_csr, .write_csr, and
.set_config_rom.
In core of Linux FireWire subsystem, the callback of .set_config_rom is
under acquisition of mutual exclusive for local list of card. The
acquision is also done in process for removal of card, therefore it's
safe for missing implementation of .set_config_rom.
On the other hand, no lock primitive accompanies any call of .read_csr and
.write_csr. For userspace client, check of node shutdown is done in the
beginning of dispatch of ioctl request, while node shifts to shutdown
state in workqueue context enough after card shifts to dummy driver. It's
probable that these two functions are called for the dummy driver by the
code of userspace client. In-kernel unit driver has similar situation.
It's better to add implementation of the two functions for dummy driver.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220405072221.226217-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes.
Notable core changes are the removal of scsi->tag which caused some
churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: lpfc: Update lpfc version to 14.0.0.3
scsi: lpfc: Allow fabric node recovery if recovery is in progress before devloss
scsi: lpfc: Fix link down processing to address NULL pointer dereference
scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to driver_resource_setup()
scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
scsi: ufs: mediatek: Avoid sched_clock() misuse
scsi: mpt3sas: Make mpt3sas_dev_attrs static
scsi: scsi_transport_sas: Add 22.5 Gbps link rate definitions
scsi: target: core: Stop using bdevname()
scsi: aha1542: Use memcpy_{from,to}_bvec()
scsi: sr: Add error handling support for add_disk()
scsi: sd: Add error handling support for add_disk()
scsi: target: Perform ALUA group changes in one step
scsi: target: Replace lun_tg_pt_gp_lock with rcu in I/O path
scsi: target: Fix alua_tg_pt_gps_count tracking
scsi: target: Fix ordered tag handling
...
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
In 1394 OHCI specification, Isochronous Receive DMA context has several
modes. One of mode is 'BufferFill' and Linux FireWire stack uses it to
receive isochronous packets for multiple isochronous channel as
FW_ISO_CONTEXT_RECEIVE_MULTICHANNEL.
The mode is not used by in-kernel driver, while it's available for
userspace. The character device driver in firewire-core includes
cast of function callback for the mode since the type of callback
function is different from the other modes. The case is inconvenient
to effort of Control Flow Integrity builds due to
-Wcast-function-type warning.
This commit removes the cast. A static helper function is newly added
to initialize isochronous context for the mode. The helper function
arranges isochronous context to assign specific callback function
after call of existent kernel API. It's noticeable that the number of
isochronous channel, speed, and the size of header are not required for
the mode. The helper function is used for the mode by character device
driver instead of direct call of existent kernel API.
The same goal can be achieved (in the ioctl_create_iso_context function)
without this helper function as follows:
- Call the fw_iso_context_create function passing NULL to the callback
parameter.
- Then setting the context->callback.sc or context->callback.mc
variables based on the a->type value.
However using the helper function created in this patch makes code more
clear and declarative. This way avoid the call to a function with one
purpose to achieved another one.
Co-developed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Co-developed-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Oscar Carter <oscar.carter@gmx.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Testeb-by: Takashi Sakamoto<o-takashi@sakamocchi.jp>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
