memstick: add driver for Ricoh R5C592 card reader

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Alex Dubov <oakad@yahoo.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS

@@ -5291,6 +5291,11 @@ S:	Maintained
 F:	drivers/mtd/nand/r852.c
 F:	drivers/mtd/nand/r852.h
 
+RICOH R5C592 MEMORYSTICK DRIVER
+M:	Maxim Levitsky <maximlevitsky@gmail.com>
+S:	Maintained
+F:	drivers/memstick/host/r592.*
+
 RISCOM8 DRIVER
 S:	Orphan
 F:	Documentation/serial/riscom8.txt

drivers/memstick/host/Kconfig

@@ -30,3 +30,15 @@ config MEMSTICK_JMICRON_38X
 
           To compile this driver as a module, choose M here: the
 	  module will be called jmb38x_ms.
+
+config MEMSTICK_R592
+	tristate "Ricoh R5C592 MemoryStick interface support (EXPERIMENTAL)"
+	depends on EXPERIMENTAL && PCI
+
+	help
+	  Say Y here if you want to be able to access MemoryStick cards with
+	  the Ricoh R5C592 MemoryStick card reader (which is part of 5 in one
+		multifunction reader)
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called r592.

drivers/memstick/host/Makefile

@@ -4,3 +4,4 @@
 
 obj-$(CONFIG_MEMSTICK_TIFM_MS)		+= tifm_ms.o
 obj-$(CONFIG_MEMSTICK_JMICRON_38X)	+= jmb38x_ms.o
+obj-$(CONFIG_MEMSTICK_R592)		+= r592.o

drivers/memstick/host/r592.h

@@ -0,0 +1,175 @@
+/*
+ * Copyright (C) 2010 - Maxim Levitsky
+ * driver for Ricoh memstick readers
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef R592_H
+
+#include <linux/memstick.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/workqueue.h>
+#include <linux/kfifo.h>
+#include <linux/ctype.h>
+
+/* write to this reg (number,len) triggers TPC execution */
+#define R592_TPC_EXEC			0x00
+#define R592_TPC_EXEC_LEN_SHIFT		16		/* Bits 16..25 are TPC len */
+#define R592_TPC_EXEC_BIG_FIFO		(1 << 26)	/* If bit 26 is set, large fifo is used (reg 48) */
+#define R592_TPC_EXEC_TPC_SHIFT		28		/* Bits 28..31 are the TPC number */
+
+
+/* Window for small TPC fifo (big endian)*/
+/* reads and writes always are done in  8 byte chunks */
+/* Not used in driver, because large fifo does better job */
+#define R592_SFIFO			0x08
+
+
+/* Status register (ms int, small fifo, IO)*/
+#define R592_STATUS			0x10
+							/* Parallel INT bits */
+#define R592_STATUS_P_CMDNACK		(1 << 16)	/* INT reg: NACK (parallel mode) */
+#define R592_STATUS_P_BREQ		(1 << 17)	/* INT reg: card ready (parallel mode)*/
+#define R592_STATUS_P_INTERR		(1 << 18)	/* INT reg: int error (parallel mode)*/
+#define R592_STATUS_P_CED		(1 << 19)	/* INT reg: command done (parallel mode) */
+
+							/* Fifo status */
+#define R592_STATUS_SFIFO_FULL		(1 << 20)	/* Small Fifo almost full (last chunk is written) */
+#define R592_STATUS_SFIFO_EMPTY		(1 << 21)	/* Small Fifo empty */
+
+							/* Error detection via CRC */
+#define R592_STATUS_SEND_ERR		(1 << 24)	/* Send failed */
+#define R592_STATUS_RECV_ERR		(1 << 25)	/* Recieve failed */
+
+							/* Card state */
+#define R592_STATUS_RDY			(1 << 28)	/* RDY signal recieved */
+#define R592_STATUS_CED			(1 << 29)	/* INT: Command done (serial mode)*/
+#define R592_STATUS_SFIFO_INPUT		(1 << 30)	/* Small fifo recieved data*/
+
+#define R592_SFIFO_SIZE			32		/* total size of small fifo is 32 bytes */
+#define R592_SFIFO_PACKET		8		/* packet size of small fifo */
+
+/* IO control */
+#define R592_IO				0x18
+#define	R592_IO_16			(1 << 16)	/* Set by default, can be cleared */
+#define	R592_IO_18			(1 << 18)	/* Set by default, can be cleared */
+#define	R592_IO_SERIAL1			(1 << 20)	/* Set by default, can be cleared, (cleared on parallel) */
+#define	R592_IO_22			(1 << 22)	/* Set by default, can be cleared */
+#define R592_IO_DIRECTION		(1 << 24)	/* TPC direction (1 write 0 read) */
+#define	R592_IO_26			(1 << 26)	/* Set by default, can be cleared */
+#define	R592_IO_SERIAL2			(1 << 30)	/* Set by default, can be cleared (cleared on parallel), serial doesn't work if unset */
+#define R592_IO_RESET			(1 << 31)	/* Reset, sets defaults*/
+
+
+/* Turns hardware on/off */
+#define R592_POWER			0x20		/* bits 0-7 writeable */
+#define R592_POWER_0			(1 << 0)	/* set on start, cleared on stop - must be set*/
+#define R592_POWER_1			(1 << 1)	/* set on start, cleared on stop - must be set*/
+#define R592_POWER_3			(1 << 3)	/* must be clear */
+#define R592_POWER_20			(1 << 5)	/* set before switch to parallel */
+
+/* IO mode*/
+#define R592_IO_MODE			0x24
+#define R592_IO_MODE_SERIAL		1
+#define R592_IO_MODE_PARALLEL		3
+
+
+/* IRQ,card detection,large fifo (first word irq status, second enable) */
+/* IRQs are ACKed by clearing the bits */
+#define R592_REG_MSC			0x28
+#define R592_REG_MSC_PRSNT		(1 << 1)	/* card present (only status)*/
+#define R592_REG_MSC_IRQ_INSERT		(1 << 8)	/* detect insert / card insered */
+#define R592_REG_MSC_IRQ_REMOVE		(1 << 9)	/* detect removal / card removed */
+#define R592_REG_MSC_FIFO_EMPTY		(1 << 10)	/* fifo is empty */
+#define R592_REG_MSC_FIFO_DMA_DONE	(1 << 11)	/* dma enable / dma done */
+
+#define R592_REG_MSC_FIFO_USER_ORN	(1 << 12)	/* set if software reads empty fifo (if R592_REG_MSC_FIFO_EMPTY is set) */
+#define R592_REG_MSC_FIFO_MISMATH	(1 << 13)	/* set if amount of data in fifo doesn't match amount in TPC */
+#define R592_REG_MSC_FIFO_DMA_ERR	(1 << 14)	/* IO failure */
+#define R592_REG_MSC_LED		(1 << 15)	/* clear to turn led off (only status)*/
+
+#define DMA_IRQ_ACK_MASK \
+	(R592_REG_MSC_FIFO_DMA_DONE | R592_REG_MSC_FIFO_DMA_ERR)
+
+#define DMA_IRQ_EN_MASK (DMA_IRQ_ACK_MASK << 16)
+
+#define IRQ_ALL_ACK_MASK 0x00007F00
+#define IRQ_ALL_EN_MASK (IRQ_ALL_ACK_MASK << 16)
+
+/* DMA address for large FIFO read/writes*/
+#define R592_FIFO_DMA			0x2C
+
+/* PIO access to large FIFO (512 bytes) (big endian)*/
+#define R592_FIFO_PIO			0x30
+#define R592_LFIFO_SIZE			512		/* large fifo size */
+
+
+/* large FIFO DMA settings */
+#define R592_FIFO_DMA_SETTINGS		0x34
+#define R592_FIFO_DMA_SETTINGS_EN	(1 << 0)	/* DMA enabled */
+#define R592_FIFO_DMA_SETTINGS_DIR	(1 << 1)	/* Dma direction (1 read, 0 write) */
+#define R592_FIFO_DMA_SETTINGS_CAP	(1 << 24)	/* Dma is aviable */
+
+/* Maybe just an delay */
+/* Bits 17..19 are just number */
+/* bit 16 is set, then bit 20 is waited */
+/* time to wait is about 50 spins * 2 ^ (bits 17..19) */
+/* seems to be possible just to ignore */
+/* Probably debug register */
+#define R592_REG38			0x38
+#define R592_REG38_CHANGE		(1 << 16)	/* Start bit */
+#define R592_REG38_DONE			(1 << 20)	/* HW set this after the delay */
+#define R592_REG38_SHIFT		17
+
+/* Debug register, written (0xABCDEF00) when error happens - not used*/
+#define R592_REG_3C			0x3C
+
+struct r592_device {
+	struct pci_dev *pci_dev;
+	struct memstick_host	*host;		/* host backpointer */
+	struct memstick_request *req;		/* current request */
+
+	/* Registers, IRQ */
+	void __iomem *mmio;
+	int irq;
+	spinlock_t irq_lock;
+	spinlock_t io_thread_lock;
+	struct timer_list detect_timer;
+
+	struct task_struct *io_thread;
+	bool parallel_mode;
+
+	DECLARE_KFIFO(pio_fifo, u8, sizeof(u32));
+
+	/* DMA area */
+	int dma_capable;
+	int dma_error;
+	struct completion dma_done;
+	void *dummy_dma_page;
+	dma_addr_t dummy_dma_page_physical_address;
+
+};
+
+#define DRV_NAME "r592"
+
+
+#define message(format, ...) \
+	printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__)
+
+#define __dbg(level, format, ...) \
+	do { \
+		if (debug >= level) \
+			printk(KERN_DEBUG DRV_NAME \
+				": " format "\n", ## __VA_ARGS__); \
+	} while (0)
+
+
+#define dbg(format, ...)		__dbg(1, format, ## __VA_ARGS__)
+#define dbg_verbose(format, ...)	__dbg(2, format, ## __VA_ARGS__)
+#define dbg_reg(format, ...)		__dbg(3, format, ## __VA_ARGS__)
+
+#endif