SPI NOR core changes:
- move SECT_4K_PMC flag out of the core as it's a vendor specific flag
- s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups.
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Call of_platform_populate() for MTD partitions
- Check devicetree alias for index
- mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
- mtdblock: Warn if opened on NAND
- Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
- st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
- phram:
- Allow cached mappings
- Allow probing via reserved-memory
- maps: ixp4xx: Drop driver
- bcm47xxpart: Print correct offset on read error
CFI driver changes:
- Rename chip_ready variables
- Add S29GL064N ID definition
- Use chip_ready() for write on S29GL064N
- Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
- Print offset instead of page number for bad blocks
Raw NAND controller drivers:
- Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
- CS553X: simplify the return expression of cs553x_write_ctrl_byte()
- Davinci: Remove redundant unsigned comparison to zero
- Denali: Use managed device resources
- GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
- Intel: Fix possible null-ptr-deref in ebu_nand_probe()
- MPC5121: Check before clk_disable_unprepare() not needed
- Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
- OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
- Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
- Rockchip: Check before clk_disable_unprepare() not needed
- TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
- Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
- Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
- XTX: Add support for XT26G0xA
SPI NOR core changes:
- Read back written SR value to make sure the write was done
correctly.
- Introduce a common function for Read ID that manufacturer drivers
can use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond
flashes use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode
for Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and
Cypress flashes since the operation is instant"
* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
dt-bindings: mtd: partitions: Extend fixed-partitions binding
dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
mtd: phram: Allow cached mappings
mtd: call of_platform_populate() for MTD partitions
mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
dt-bindings: mtd: renesas: Fix the NAND controller description
mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
mtd: spi-nor: debugfs: fix format specifier
mtd: spi-nor: support eon en25qh256a variant
mtd: spi-nor: winbond: add support for W25Q512NW-IM
mtd: spi-nor: expose internal parameters via debugfs
mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
mtd: spi-nor: move spi_nor_write_ear() to winbond module
mtd: spi-nor: amend the rdsr dummy cycles documentation
mtd: cfi_cmdset_0002: Rename chip_ready variables
...
NAND core:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI NOR core changes:
- Read back written SR value to make sure the write was done correctly.
- Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc
The "Extended Address Register" is winbond specific. If the flash is
larger than 16MiB and is used in 3 byte address mode, it is used to set
the remaining address bits. Move the write_ear() function, the opcode
macros and the spimem op template into the winbond module and rename
them accordingly.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429100153.2338501-1-michael@walle.cc
Mediatek ECC changes:
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 46b5889cc2 ("mtd: implement proper partition handling")
started using "mtd_get_master_ofs()" in mtd callbacks to determine
memory offsets by means of 'part' field from mtd_info, what previously
was smashed accessing 'master' field in the mtd_set_dev_defaults() method.
That provides wrong offset what causes hardware access errors.
Just make 'part', 'master' as separate fields, rather than using
union type to avoid 'part' data corruption when mtd_set_dev_defaults()
is called.
Fixes: 46b5889cc2 ("mtd: implement proper partition handling")
Signed-off-by: Oleksandr Ocheretnyi <oocheret@cisco.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220417184649.449289-1-oocheret@cisco.com
Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The flag status register is only available on micron flashes. Move all
the functions around that into the micron module.
This is almost a mechanical move except for the spi_nor_fsr_ready()
which now also checks the normal status register. Previously, this was
done in spi_nor_ready().
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-25-michael@walle.cc
Topic branch bringing-in changes related to the support of ECC engines
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Some SPI-NAND chips do not have a proper on-die ECC engine providing
error correction/detection. This is particularly an issue on embedded
devices with limited resources because all the computations must
happen in software, unless an external hardware engine is provided.
These external engines are new and can be of two categories: external
or pipelined. Macronix is providing both, the former being already
supported. The second, however, is very SoC implementation dependent
and must be instantiated by the SPI host controller directly.
An entire subsystem has been contributed to support these engines which
makes the insertion into another subsystem such as SPI quite
straightforward without the need for a lot of specific functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20220202144536.393792-1-miquel.raynal@bootlin.com
In order for pipelined ECC engines to be able to enable/disable the ECC
engine only when needed and avoid races when future parallel-operations
will be supported, we need to provide the information about the use of
the ECC engine in the direct mapping hooks. As direct mapping
configurations are meant to be static, it is best to create two new
mappings: one for regular 'raw' accesses and one for accesses involving
correction. It is up to the driver to use or not the new ECC enable
boolean contained in the spi-mem operation.
As dirmaps are not free (they consume a few pages of MMIO address space)
and because these extra entries are only meant to be used by pipelined
engines, let's limit their use to this specific type of engine and save
a bit of memory with all the other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-9-miquel.raynal@bootlin.com
Introduce the support for another possible configuration: the ECC
engine may work as DMA master (pipelined) and move itself the data
to/from the NAND chip into the buffer, applying the necessary
corrections/computations on the fly.
This driver offers an ECC engine implementation that must be
instatiated from a SPI controller driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-17-miquel.raynal@bootlin.com
