2nd round of GPIO changes for v3.3 merge window
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
GPIO: sa1100: implement proper gpiolib gpio_to_irq conversion
gpio: pl061: remove combined interrupt
gpio: pl061: convert to use generic irq chip
GPIO: add bindings for managed devices
ARM: realview: convert pl061 no irq to 0 instead of -1
gpio: pl061: convert to use 0 for no irq
gpio: pl061: use chained_irq_* functions in irq handler
GPIO/pl061: Add suspend resume capability
drivers/gpio/gpio-tegra.c: use devm_request_and_ioremap
MMC highlights for 3.3:
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
* tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (58 commits)
mmc: fix a deadlock between system suspend and MMC block IO
mmc: sdhci: restore the enabled dma when do reset all
mmc: dw_mmc: miscaculated the fifo-depth with wrong bit operation
mmc: host: Adds support for eMMC 4.5 HS200 mode
mmc: core: HS200 mode support for eMMC 4.5
mmc: dw_mmc: fixed wrong bit operation for SDMMC_GET_FCNT()
mmc: core: Separate the timeout value for cache-ctrl
mmc: sdhci-spear: Fix compilation error
mmc: sdhci: Deal with failure case in sdhci_suspend_host
mmc: dw_mmc: Clear the DDR mode for non-DDR
mmc: sd: Fix SDR12 timing regression
mmc: sdhci: Fix tuning timer incorrect setting when suspending host
mmc: core: Add option to prevent eMMC sleep command
mmc: omap_hsmmc: use threaded irq handler for card-detect.
mmc: sdhci-pci: enable runtime PM for Medfield SDIO
mmc: sdhci: Always pass clock request value zero to set_clock host op
mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION
mmc: sdhci-pci: get gpio numbers from platform data
mmc: sdhci-pci: add platform data
mmc: sdhci: prevent card detection activity for non-removable cards
...
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
Changes queued in gpio/next for the start of the 3.3 merge window
* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add decode of WM8994 GPIO configuration
gpio: Convert GPIO drivers to module_platform_driver
gpio: Fix typo in comment in Samsung driver
gpio: Explicitly index samsung_gpio_cfgs
gpio: Add Linus Walleij as gpio co-maintainer
of: Add device tree selftests
of: create of_phandle_args to simplify return of phandle parsing data
gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
gpiolib: output basic details and consolidate gpio device drivers
pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
spi/pl022: make the chip deselect handling thread safe
spi/pl022: add support for pm_runtime autosuspend
spi/pl022: disable the PL022 block when unused
spi/pl022: move device disable to workqueue thread
spi/pl022: skip default configuration before suspending
spi/pl022: fix build warnings
spi/pl022: only enable RX interrupts when TX is complete
The transfer direction for a channel can be inferred from the transfer
request and the need for specifying transfer direction in platfrom data
can be eliminated. So the structure definition 'struct dma_pl330_peri'
is no longer required.
The channel's private data is set to point to a channel id specified in
the platform data (instead of an instance of type 'struct dma_pl330_peri').
The filter function is correspondingly modified to match the channel id.
With the 'struct dma_pl330_peri' removed from platform data, the dma
controller transfer capabilities cannot be inferred any more. Hence,
the dma controller capabilities is specified using platform data.
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The dma channel selection filter function is moved from plat-samsung
into the pl330 driver. In additon to that, a check is added in the
filter function to ensure that the channel on which the filter has
been invoked is pl330 channel instance (and avoid any incorrect
access of chan->private in a system with multiple types of DMA
drivers).
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds support for configuring the spi bus to use autosuspend for
runtime power management. This can reduce the latency in starting an
spi transfer by not suspending the device immediately following
completion of a transfer. If another transfer then takes place before
the autosuspend timeout, the call to resume the device can return
immediately rather than needing to risk sleeping in order to resume
the device.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The general kernel infrastructure for adding module alises during
module post processing expects the affected device type
identification structures in a common header
<linux/mod_devicetable.h>.
This patch simple moves struct amba_id to the common header, and
adds the appropriate include in <linux/amba/bus.h>.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (63 commits)
dmaengine: mid_dma: mask_peripheral_interrupt only when dmac is idle
dmaengine/ep93xx_dma: add module.h include
pch_dma: Reduce wasting memory
pch_dma: Fix suspend issue
dma/timberdale: free_irq() on an error path
dma: shdma: transfer based runtime PM
dmaengine: shdma: protect against the IRQ handler
dmaengine i.MX DMA/SDMA: add missing include of linux/module.h
dmaengine: delete redundant chan_id and chancnt initialization in dma drivers
dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_pool
dmaengine/amba-pl08x: Add support for sg len greater than one for slave transfers
serial: sh-sci: don't filter on DMA device, use only channel ID
ARM: SAMSUNG: Remove Samsung specific enum type for dma direction
ASoC: Samsung: Update DMA interface
spi/s3c64xx: Merge dma control code
spi/s3c64xx: Add support DMA engine API
ARM: SAMSUNG: Remove S3C-PL330-DMA driver
ARM: S5P64X0: Use generic DMA PL330 driver
ARM: S5PC100: Use generic DMA PL330 driver
ARM: S5PV210: Use generic DMA PL330 driver
...
Fix up fairly trivial conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
- arch/arm/mach-s5p64x0/dma.c
This adds devicetree binding support to the ARM pl061 driver removing the
platform_data dependency. When DT binding is used, the gpio numbering is
assigned dynamically. For now, interrupts are not supported with DT until
irqdomains learn dynamic irq assignment.
Rather than add another case of -1, updating the driver to use NO_IRQ.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Untill now, sg_len greater than one is not supported. This patch adds support to
do that.
Note: Still, if peripheral is flow controller, sg_len can't be greater that one.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
At least, on SPEAr platforms there is one peripheral, JPEG, which can be flow
controller for DMA transfer. Currently DMA controller driver didn't support
peripheral flow controller configurations.
This patch adds device_fc field in struct pl08x_channel_data, which will be used
only for slave transfers and is not used in case of mem2mem transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pl080 Manual says: "Bursts do not cross the 1KB address boundary"
We can program the controller to cross 1 KB boundary on a burst and controller
can take care of this boundary condition by itself.
Following is the discussion with ARM Technical Support Guys (David):
[Viresh] Manual says: "Bursts do not cross the 1KB address boundary"
What does that actually mean? As, Maximum size transferable with a single LLI is
4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst
size, we can't use this big of an LLI.
[David] There is a difference between bursts describing the total data
transferred by the DMA controller and AHB bursts. Bursts described by the
programmable parameters in the PL080 have no direct connection with the bursts
that are seen on the AHB bus.
The statement that "Bursts do not cross the 1KB address boundary" in the TRM is
referring to AHB bursts, where this limitation is a requirement of the AHB spec.
You can still issue bursts within the PL080 that are in excess of 1KB. The
PL080 will make sure that its bursts are broken down into legal AHB bursts which
will be formatted to ensure that no AHB burst crosses a 1KB boundary.
Based on above discussion, this patch removes all code related to 1 KB boundary
as we are not required to handle this in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination cctl values into the channel structure.
This moves us towards being able to avoid a configuration call each
time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
