Introduce a regulator_can_change_voltage() function for the subsytems or
drivers which might check if applying voltage change is possible and use
special workaround code when the driver is used with fixed regulators or
regulators with disabled ability to change the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some drivers (at least 3 drivers) have such variant of linear mapping that
the first few selectors are invalid and the reset are linear mapping.
Let's support this case in core.
This patch adds linear_min_sel in struct regulator_desc,
so we can allow specific minimal selector for starting linear mapping.
Then extends regulator_[map|list]_voltage_linear() to support this feature.
Note that for selectors less than min_linear_index, we need count them to
n_voltages so regulator_list_voltage() won't fail while checking the boundary
for selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.
Add regulator driver for this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If consumers wish to set voltages based on a tolerance it stands to reason
that they will also want to query for support in the same manner.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
MFD driver registers the regulator driver once per device and
hence it is require to register all regulators in single probe
call.
Following are details of changes done to achieve this:
- Move the regulator enums to mfd header and remove the
tps65090-regulator.h as it does not contain more info.
- Add max regulator and register all regulators even if there
is no regulator init data from platform.
- Convert regulator init data to pointer type in platform data.
- Add input supply name in regulator desc to provide input supply.
- Separate desc information from driver information.
- Disable external control bit to have control through register write.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some regulators can set any voltage within the constraints range,
not being limited to specified operating points.
This patch makes it possible to describe such regulator and makes
the regulator_is_supported_voltage() function behave correctly.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TPS51632 is a driverless step down controller with
serial control. Advanced features such as D-Cap+
architecture with overlapping pulse support and OSR
overshoot reduction provide fast transient response,
lowest output capacitance and high efficiency.
The TPS51632 supports both I2C and DVFS interfaces
(through PWM) for dynamic control of the output voltage
and current monitor telemetry.
Add regulator driver for TPS51632.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many regulators support a bypass mode where they simply switch their
input supply to the output. This is mainly used in low power retention
states where power consumption is extremely low so higher voltage or
less clean supplies can be used.
Support this by providing ops for the drivers and a consumer API which
allows the device to be put into bypass mode if all consumers enable it
and the machine enables permission for this.
This is not supported as a mode since the existing modes are rarely used
due to fuzzy definition and mostly redundant with modern hardware which is
able to respond promptly to load changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Graeme Gregory <gg@slimlogic.co.uk>
This driver supports Fairchild FAN53555 Digitally Programmable
TinyBuck Regulator. The FAN53555 is a step-down switching voltage
regulator that delivers a digitally programmable output from an
input voltage supply of 2.5V to 5.5V. The output voltage is
programmed through an I2C interface.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulators should be tending to the maximum in the available range and
consumers should specify the widest range possible.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are some use cases where a voltage range could be reasonably
specified by a target voltage and tolerance. Add a new API
regulator_set_voltage_tol() wrapping regulator_set_voltage() call
to ease the users.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
