What the PCF05633 calls as a 'GPIO' is much more than the GPIO in the linux
sense and there are only 4 of them - which means, the gpiolib is not used
here.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds basic support for the PCF50633 ADC. The subtractive mode
is not supported yet.
Since we don't have adc subsystem, it currently lives in drivers/mfd.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Acked-by: Jonathan Cameron <jonathan.cameron@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch implements the core of the PCF50633 driver. This core driver has
generic register read/write functions and does interrupt management for its
sub devices.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver. This driver
implements support for this within the standard LED class.
Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver. The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.
This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The WM8351 is a WM8350 variant. As well as register default changes the
WM8351 has fewer voltage and current regulators than the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Some WM8350 variants have fewer DCDCs and ISINKs. Identify these at
probe and refuse to use the absent DCDCs when running on these chips.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8352 is a variant of the WM8350. Aside from the register defaults
there are no software visible differences to the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch amends DA903x MFD driver with definitions and methods
needed for battery charger driver.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Implement support for reporting battery health in the WM8350 battery
interface. Since we are now able to report this via the classs remove
the diagnostics from the interrupt handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Since the WM8350 driver was originally written the semantics for the
identification registers of the chip have been clarified, allowing
us to do an exact match on all the fields. This avoids mistakenly
running on unsupported hardware.
Also change to using the datasheet names more consistently for
legibility and fix a printk() that should be dev_err().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Rather than check for chip revisions in the WM8350 drivers have the core
code set flags for relevant differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the PMU provided by the WM8350 which
implements battery, line and USB supplies including a battery charger.
The hardware functions largely autonomously, with minimal software
control required to initiate fast charging.
Support for configuration of the USB supply is not yet implemented.
This means that the hardware will remain in the mode configured at
startup, by default limiting the current drawn from USB to 100mA.
This driver was originally written by Liam Girdwood with subsequent
updates for submission by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The auxiliary ADC in the WM8350 is shared between several subdevices
so access to it needs to be arbitrated by the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8350 is an integrated audio and power management subsystem which
provides a single-chip solution for portable audio and multimedia systems.
The integrated audio CODEC provides all the necessary functions for
high-quality stereo recording and playback. Programmable on-chip
amplifiers allow for the direct connection of headphones and microphones
with a minimum of external components. A programmable low-noise bias
voltage is available to feed one or more electret microphones.
Additional audio features include programmable high-pass filter in the
ADC input path.
This driver was originally written by Liam Girdwood with further updates
from me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds support for the RTC provided by the Wolfson Microelectronics
WM8350.
This driver was originally written by Graeme Gregory and Liam Girdwood,
though it has been modified since then to update it to current mainline
coding standards and for API completeness.
[akpm@linux-foundation.org: s/schedule_timeout_interruptible/schedule_timeout_uninterruptible/ to prevent bogus timeout when signal_pending()]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Liam Girdwood <linux@wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates the remaining two TMIO drivers to use the clock API
rather than callback hooks into platform code.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
DA9030 (a.k.a ARAVA) and DA9034 (a.k.a MICCO) are PMICs designed by
Dialog Semiconductor, usually found on PXA-based platforms. These
PMICs are I2C-based, multi-function devices, usually with LEDs, PWMs
for backlight, BUCKs and LDOs, ADCs and touchscreen controller (on
DA9034).
This is the base support for the I2C operations, event registration
and handling, sub-devices management.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Liam Girdwood <lrg@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
As requested by Ian make state restore only if it's requested
by platform data: some platforms do correctly save the state of
the chip during suspend/resume, but some (like tosa) incorrectly
power off the chip at suspend, so the driver supports restoring
some bits of the tc6393xb state (not full, merely enough to support
resume on tosa). With this patch this code is disabled by default.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Instead of using bitfields for initial gpio setup,
provide generic setup/teardown hooks that can be used
to set the gpio states, register child devices, etc.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
