After this driver was converted to gpiod, clang started warning:
vers/regulator/lp872x.c:689:57: error: implicit conversion from
enumeration type 'enum lp872x_dvs_state' to different enumeration type
'enum gpiod_flags' [-Werror,-Wenum-conversion]
dvs->gpio = devm_gpiod_get_optional(lp->dev, "ti,dvs", pinstate);
~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~
1 error generated.
lp872x_dvs_state was updated to have values from gpiod_flags but this is
not enough to avoid an implicit conversion warning from either GCC or
clang (although GCC enables this warning under -Wextra instead of -Wall
like clang so it is not seen under normal builds).
Eliminate lp872x_dvs_state in favor of using gpiod_flags everywhere so
that there is no more warning about an implicit conversion.
Fixes: 72bf80cf09 ("regulator: lp872x: replacing legacy gpio interface for gpiod")
Link: https://github.com/ClangBuiltLinux/linux/issues/1481
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211019004335.193492-1-nathan@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Removing all linux/gpio.h and linux/of_gpio.h dependencies and replacing
them with the gpiod interface
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Message-Id: <YWma2yTyuwS5XwhY@fedora>
Signed-off-by: Mark Brown <broonie@kernel.org>
The helper to send IRQ notification for regulator errors had still
old description mentioning calling BUG() as a last resort when
error status reading has kept failing for more times than a given
threshold.
The impementation calling BUG() did never end-up in-tree but was
replaced by hopefully more sophisticated handler trying to power-off
the system.
Fix the documentation to reflect actual behaviour.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210823075651.GA3717293@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
These APIs aren't used anywhere and most-likely exist because of the
general principle of C APIs, where if an API function does an
allocation/registration, it must also have an equivalent
deallocation/deregistration counterpart.
For devm_ functions this isn't all that true (for all cases), as the idea
of these function is to provide an auto-cleanup logic on drivers/system
de-init.
Removing these discourages any weird logic that could be created with
such an API functions.
Alexandru Ardelean (4):
regulator: devres: remove devm_regulator_unregister_notifier()
function
regulator: devres: remove devm_regulator_unregister() function
regulator: devres: remove
devm_regulator_bulk_unregister_supply_alias()
regulator: devres: unexport devm_regulator_unregister_supply_alias()
drivers/regulator/devres.c | 105 +----------------------------
include/linux/regulator/consumer.h | 23 -------
include/linux/regulator/driver.h | 1 -
3 files changed, 2 insertions(+), 127 deletions(-)
--
2.31.1
This API hook isn't used anywhere outside of the regulator devres code.
This function is needed for the devm_regulator_bulk_register_supply_alias()
function on the error path, to cleanup any previously registered supply
aliases.
This change makes the devm_regulator_unregister_supply_alias() local to the
regulator core framework, to avoid it being used in any weird logic.
It's also removing the doc-string for
devm_regulator_unregister_supply_alias(), since it doesn't need to be
documented anymore, as no other external consumer should use it.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210625122324.327585-5-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This API hook isn't used anywhere and most-likely exists because of the
general principle of C APIs, where if an API function does an
allocation/registration, it must also have an equivalent
deallocation/deregistration counterpart.
For devm_ functions this isn't all that true (for all cases), as the idea
of these function is to provide an auto-cleanup logic on drivers/system
de-init.
Removing this also discourages any weird logic that could be created with
such an API function.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210625122324.327585-4-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This API hook isn't used anywhere and most-likely exists because of the
general principle of C APIs, where if an API function does an
allocation/registration, it must also have an equivalent
deallocation/deregistration counterpart.
For devm_ functions this isn't all that true (for all cases), as the idea
of these function is to provide an auto-cleanup logic on drivers/system
de-init.
Removing this also discourages any weird logic that could be created with
such an API function.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210625122324.327585-3-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend regulator notification support
This series extends the regulator notification and error flag support.
Initial discussion on the topic can be found here:
https://lore.kernel.org/lkml/6046836e22b8252983f08d5621c35ececb97820d.camel@fi.rohmeurope.com/
In a nutshell - the series adds:
1. WARNING level events/error flags. (Patch 3)
Current regulator 'ERROR' event notifications for over/under
voltage, over current and over temperature are used to indicate
condition where monitored entity is so badly "off" that it actually
indicates a hardware error which can not be recovered. The most
typical hanling for that is believed to be a (graceful)
system-shutdown. Here we add set of 'WARNING' level flags to allow
sending notifications to consumers before things are 'that badly off'
so that consumer drivers can implement recovery-actions.
2. Device-tree properties for specifying limit values. (Patches 1, 5)
Add limits for above mentioned 'ERROR' and 'WARNING' levels (which
send notifications to consumers) and also for a 'PROTECTION' level
(which will be used to immediately shut-down the regulator(s) W/O
informing consumer drivers. Typically implemented by hardware).
Property parsing is implemented in regulator core which then calls
callback operations for limit setting from the IC drivers. A
warning is emitted if protection is requested by device tree but the
underlying IC does not support configuring requested protection.
3. Helpers which can be registered by IC. (Patch 4)
Target is to avoid implementing IRQ handling and IRQ storm protection
in each IC driver. (Many of the ICs implementin these IRQs do not allow
masking or acking the IRQ but keep the IRQ asserted for the whole
duration of problem keeping the processor in IRQ handling loop).
4. Emergency poweroff function (refactored out of the thermal_core to
kernel/reboot.c) which is called if IC fires error IRQs but IC reading
fails and given retry-count is exceeded. (Patches 2, 4)
Please note that the mutex in the emergency shutdown was replaced by a
simple atomic in order to allow call from any context.
The helper was attempted to be done so it could be used to implement
roughly same logic as is used in qcom-labibb regulator. This means
amongst other things a safety shut-down if IC registers are not readable.
Using these shut-down retry counters are optional. The idea is that the
helper could be also used by simpler ICs which do not provide status
register(s) which can be used to check if error is still active.
ICs which do not have such status register can simply omit the 'renable'
callback (and retry-counts etc) - and helper assumes the situation is Ok
and re-enables IRQ after given time period. If problem persists the
handler is ran again and another notification is sent - but at least the
delay allows processor to avoid IRQ loop.
Patch 7 takes this notification support in use at BD9576MUF.
Patch 8 is related to MFD change which is not really related to the RFC
here. It was added to this series in order to avoid potential conflicts.
Patch 9 adds a maintainers entry.
Changelog v10-RESEND:
- rebased on v5.13-rc4
Changelog v10:
- rebased on v5.13-rc2
- Move rdev_*() print macros to the internal.h and use rdev_dbg()
from irq_helpers.c
- Export rdev_get_name() and move it from coupler.h to driver.h for
others to use. (It was already in coupler.h but not exported -
usage was limited and coupler.h does not sound like optimal place
as rdev_name is not only used by coupled regulators)
- Send all regulator notifications from irq_helpers.c at one OR'd
event for the sake of simplicity. For BD9576 this does not matter
as it has own IRQ for each event case. Header defining events says
they may be OR'd.
- Change WARN() at protection shutdown to pr_emerg as suggested by
Petr.
Changelog v9:
- rebases on v5.13-rc1
- Update thermal documentation
- Fix regulator notification event number
Changelog v8:
- split shutdown API adding and thermal core taking it in use to
own patches.
- replace the spinlock with atomic when ensuring the emergency
shutdown is only called once.
Changelog v7:
general:
- rebased on v5.12-rc7
- new patch for refactoring the hw-failure reboot logic out of
thermal_core.c for others to use.
notification helpers:
- fix regulator error_flags query
- grammar/typos
- do not BUG() but attempt to shut-down the system
- use BITS_PER_TYPE()
Changelog v6:
Add MAINTAINERS entry
Changes to IRQ notifiers
- move devm functions to drivers/regulator/devres.c
- drop irq validity check
- use devm_add_action_or_reset()
- fix styling issues
- fix kerneldocs
Changelog v5:
- Fix the badly formatted pr_emerg() call.
Changelog v4:
- rebased on v5.12-rc6
- dropped RFC
- fix external FET DT-binding.
- improve prints for cases when expecting HW failure.
- styling and typos
Changelog v3:
Regulator core:
- Fix dangling pointer access at regulator_irq_helper()
stpmic1_regulator:
- fix function prototype (compile error)
bd9576-regulator:
- Update over current limits to what was given in new data-sheet
(REV00K)
- Allow over-current monitoring without external FET. Set limits to
values given in data-sheet (REV00K).
Changelog v2:
Generic:
- rebase on v5.12-rc2 + BD9576 series
- Split devm variant of delayed wq to own series
Regulator framework:
- Provide non devm variant of IRQ notification helpers
- shorten dt-property names as suggested by Rob
- unconditionally call map_event in IRQ handling and require it to be
populated
BD9576 regulators:
- change the FET resistance property to micro-ohms
- fix voltage computation in OC limit setting
Add 'warning' level events and error flags to regulator core.
Current regulator core notifications are used to inform consumers
about errors where HW is misbehaving in such way it is assumed to
be broken/unrecoverable.
There are PMICs which are designed for system(s) that may have use
for regulator indications sent before HW is damaged so that some
board/consumer specific recovery-event can be performed while
continuing most of the normal operations.
Add new WARNING level events and notifications to be used for
that purpose.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/9b54aa5589ae4b5945d53d114bac3fae55fa4818.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6359 is a regulator found on boards based on MediaTek MT6779 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Wen Su <wen.su@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some NVIDIA Tegra devices use a CPU soft-reset method for the reboot and
in this case we need to restore the coupled voltages to the state that is
suitable for hardware during boot. Add new regulator_sync_voltage_rdev()
helper which is needed by regulator drivers in order to sync voltage of
a coupled regulators.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The jiffies-based off_on_delay implementation has a couple of problems
that cause it to sometimes not actually delay for the required time:
(1) If, for example, the off_on_delay time is equivalent to one jiffy,
and the ->last_off_jiffy is set just before a new jiffy starts,
then _regulator_do_enable() does not wait at all since it checks
using time_before().
(2) When jiffies overflows, the value of "remaining" becomes higher
than "max_delay" and the code simply proceeds without waiting.
Fix these problems by changing it to use ktime_t instead.
[Note that since jiffies doesn't start at zero but at INITIAL_JIFFIES
("-5 minutes"), (2) above also led to the code not delaying if
the first regulator_enable() is called when the ->last_off_jiffy is not
initialised, such as for regulators with ->constraints->boot_on set.
It's not clear to me if this was intended or not, but I've preserved
this behaviour explicitly with the check for a non-zero ->last_off.]
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20210423114524.26414-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
