Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Convert list_for_each to entry variant
- Use MTD_DEVICE_ATTR_RO/RW() helper macros
- Remove unnecessary OOM messages
- Potential NULL dereference in mtd_otp_size()
- Fix freeing of otp_info buffer
- Create partname and partid debug files for child MTDs
- tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
- Add OTP NVMEM provider support
- Allow specifying of_node
- Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
- Convert ti,am654-hbmc.txt to YAML schema
- spi-nor: add otp property
- Add OTP bindings
- add YAML schema for the generic MTD bindings
- Add brcm,trx-magic
MTD device drivers changes:
- Add support for microchip 48l640 EERAM
- Remove superfluous "break"
- sm_ftl:
- Fix alignment of block comment
- nftl:
- Return -ENOMEM when kmalloc failed
- nftlcore:
- Remove set but rewrite variables
- phram:
- Fix error return code in phram_setup()
- plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
- Qcom:
- Fix leaking of partition name
- Redboot:
- Fix style issues
- Seek fis-index-block in the right node
- trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
- Allow SDR timings to be nacked
- Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing
set.
- Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
- Update dead URL
- Silence static checker warning in nand_setup_interface()
- BBT:
- Fix corner case in bad block table handling
- onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
- Atmel:
- Ensure the data interface is supported.
- Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
- brcmnand:
- Convert bindings to json-schema
- OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
- PL35X:
- New driver
- QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
- Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in
marvell_nfc_resume()
- R852:
- Use DEVICE_ATTR_RO() helper macro
- MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
- HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
- Light reorganisation for the introduction of a core resume handler
- Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
- Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support"
* tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (125 commits)
mtd: spi-nor: remove redundant continue statement
mtd: rawnand: omap: Add larger page NAND chips support
mtd: rawnand: omap: Various style fixes
mtd: rawnand: omap: Check return values
mtd: rawnand: omap: Rename a macro
mtd: rawnand: omap: Aggregate the HW configuration of the ELM
mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller
dt-bindings: mtd: pl353-nand: Describe this hardware controller
MAINTAINERS: Add PL353 NAND controller entry
mtd: rawnand: qcom: avoid writing to obsolete register
mtd: rawnand: marvell: Minor documentation correction
mtd: rawnand: r852: use DEVICE_ATTR_RO() helper macro
mtd: spinand: add SPI-NAND MTD resume handler
mtd: spinand: Add spinand_init_flash() helper
mtd: spinand: add spinand_read_cfg() helper
mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()
mtd: rawnand: arasan: Finer grain NV-DDR configuration
mtd: rawnand: arasan: Rename the data interface register
mtd: rawnand: onfi: Fix endianness when reading NV-DDR values
mtd: rawnand: arasan: Use the right DMA mask
...
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
Due to possible mode switching to 8D-8D-8D, it might not be possible to
read the SFDP after the initial probe. To be able to dump the SFDP via
sysfs afterwards, make a complete copy of it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.
Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-3-miquel.raynal@bootlin.com
Until now the parameter of the ADDR_TIMING_MODE feature was just the
ONFI timing mode (from 0 to 5) because we were only supporting the SDR
data interface. In the same byte, bits 4 and 5 indicate which data
interface is being configured so use them to set the right mode and also
read them back to ensure the right timing has been setup on the chip's
side.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-17-miquel.raynal@bootlin.com
Most timings related to the bus timings are different between SDR and
NV-DDR. However, we identified 9 individual timings which are more
related to the NAND chip internals. These are common between the two
interface types. Fortunately, only these common timings are being shared
through the NAND core and its ->exec_op() interface, which allows the
writing of a simple macro checking the interface type and depending on
it, returning either the relevant SDR timing or the NV-DDR timing. This
is the purpose of the NAND_COMMON_TIMING_PS() macro.
As all this is evaluated at build time, one will immediately be notified
in case a non common timing is being accessed through this macro.
Two handy macros are also inserted at the same time, which use
PSEC_TO_NSEC or PSEC_TO_MSEC so that it is very easy to return timings
in milli-, nano- or pico-seconds, as usually requested by the internal
API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-14-miquel.raynal@bootlin.com
Same logic as for the SDR path, let's create a
onfi_fill_nvddr_interface_config() helper to fill an interface
configuration structure with NV-DDR timings, given a specific ONFI mode.
There is one additional thing to do compared to SDR mode: tCAD timing
can be fast or slow and this depends on an ONFI parameter page bit. By
default the slow value is declared in the timings structure definition,
but this helper can shrink it down if necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-12-miquel.raynal@bootlin.com
Both src_sync_timing_mode and src_ssync_features entries of the ONFI
parameter page have been updated and now are named nvddr_timing_modes,
nvddr2_timing_modes and nvddr_nvddr2_features, which is much more
understandable for someone which do not know the history of the ONFI
specification. Update the relevant structure with regard to these
changes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-8-miquel.raynal@bootlin.com
Flash OTP regions can already be read via user space. Some boards have
their serial number or MAC addresses stored in the OTP regions. Add
support for them being a (read-only) nvmem provider.
The API to read the OTP data is already in place. It distinguishes
between factory and user OTP, thus there are up to two different
providers.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210424110608.15748-6-michael@walle.cc
The write buffer comes from user and should be const.
Constify write buffer in mtd core and across all _write_user_prot_reg()
users. cfi_cmdset_{0001, 0002} and onenand_base will pay the cost of an
explicit cast to discard the const qualifier since the beginning, since
they are using an otp_op_t function prototype that is used for both reads
and writes. mtd_dataflash and SPI NOR will benefit of the const buffer
because they are using different paths for writes and reads.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060931.7119-1-tudor.ambarus@microchip.com
MTD core:
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
SPI NOR core changes:
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
SPI NOR controller drivers changes:
- intel-spi: Move platform data header to x86 subfolder
On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).
The regions are declared using a NAND chip DT property,
"secure-regions". So let's make use of this property in the raw NAND
core and skip access to the secure regions present in a system.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-4-manivannan.sadhasivam@linaro.org
Use the new OTP ops to implement OTP access on Winbond flashes. Most
Winbond flashes provides up to four different OTP regions ("Security
Registers").
Winbond devices use a special opcode to read and write to the OTP
regions, just like the RDSFDP opcode. In fact, it seems that the
(undocumented) first OTP area of the newer flashes is the actual SFDP
table.
On a side note, Winbond devices also allow erasing the OTP regions as
long as the area isn't locked down.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-3-michael@walle.cc
