Pull char / misc driver updates from Greg KH:
"Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here,
notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanalabs driver updates in this pull request,
that will probably come later before -rc1 is out in a different
request.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
Revert "bus: mhi: Add inbound buffers allocation flag"
misc/pvpanic: fix set driver data
VMCI: fix NULL pointer dereference when unmapping queue pair
char: mware: fix returnvar.cocci warnings
parport: remove non-zero check on count
soundwire: cadence: do not extend reset delay
soundwire: intel: conditionally exit clock stop mode on system suspend
soundwire: intel: skip suspend/resume/wake when link was not started
soundwire: intel: fix potential race condition during power down
phy: qcom-qmp: Add support for SM6115 UFS phy
dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings
phy: qmp: Provide unique clock names for DP clocks
lkdtm: remove IDE_CORE_CP crashpoint
lkdtm: replace SCSI_DISPATCH_CMD with SCSI_QUEUE_RQ
coresight: Replace deprecated CPU-hotplug functions.
Documentation: coresight: Add documentation for CoreSight config
coresight: syscfg: Add initial configfs support
coresight: config: Add preloaded configurations
coresight: etm4x: Add complex configuration handlers to etmv4
coresight: etm-perf: Update to activate selected configuration
...
This reverts commit ce78ffa3ef.
Wren and Nicolas reported that ath11k was failing to initialise QCA6390
Wi-Fi 6 device with error:
qcom_mhi_qrtr: probe of mhi0_IPCR failed with error -22
Commit ce78ffa3ef ("net: really fix the build..."), introduced in
v5.14-rc5, caused this regression in qrtr. Most likely all ath11k
devices are broken, but I only tested QCA6390. Let's revert the broken
commit so that ath11k works again.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210826172816.24478-1-kvalo@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MRU value used by the MHI MBIM network interface affects
the throughput performance of the interface. Different modem
models use different default MRU sizes based on their bandwidth
capabilities. Large values generally result in higher throughput
for larger packet sizes.
In addition if the MRU used by the MHI device is larger than that
specified in the MHI net device the data is fragmented and needs
to be re-assembled which generates a (single) warning message about
the fragmented packets. Setting the MRU on both ends avoids the
extra processing to re-assemble the packets.
This patch allows the documented MRU for a modem to be automatically
set as the MHI net device MRU avoiding fragmentation and improving
throughput performance.
Signed-off-by: Richard Laing <richard.laing@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some controllers can choose to skip preparation for power up.
In that case, device context is initialized based on the pre_init
flag not being set during mhi_prepare_for_power_up(). There is no
reason MHI host driver should maintain and provide controllers
with two separate paths for preparing MHI.
Going forward, all controllers will be required to call the
mhi_prepare_for_power_up() API followed by their choice of sync
or async power up. This allows MHI host driver to get rid of the
pre_init flag and sets up a common way for all controllers to use
MHI. This also helps controllers fail early on during preparation
phase in some failure cases.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617313309-24035-1-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI WWAN modems support downloading firmware to NAND or eMMC
using Firehose protocol with process as follows:
1. Modem boots up, enters AMSS execution environment and the
device later enters EDL (Emergency Download) mode through any
mechanism host can use such as a diag command.
2. Modem enters SYS_ERROR, MHI host handles SYS_ERROR transition.
3. EDL image for device to enter 'Flash Programmer' execution
environment is then flashed via BHI interface from host.
4. Modem enters MHI READY -> M0 and sends the Flash Programmer
execution environment change to host.
5. Following that, EDL/FIREHOSE channels (34, 35) are made
available from the host.
6. User space tool for downloading firmware image to modem over
the EDL channels using Firehose protocol. Link to USB flashing
tool: https://git.linaro.org/landing-teams/working/qualcomm/qdl.git/
Make the necessary changes to allow for this sequence to occur and
allow using the Flash Programmer execution environment.
Signed-off-by: Carl Yin <carl.yin@quectel.com>
Co-developed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617067704-28850-5-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If controller driver has specified the irq_flags, mhi uses this specified
irq_flags. Otherwise, mhi uses default irq_flags.
The purpose of this change is to support one MSI vector for QCA6390.
MHI will use one same MSI vector too in this scenario.
In case of one MSI vector, IRQ_NO_BALANCING is needed when irq handler
is requested. The reason is if irq migration happens, the msi_data may
change too. However, the msi_data is already programmed to QCA6390
hardware during initialization phase. This msi_data inconsistence will
result in crash in kernel.
Another issue is in case of one MSI vector, IRQF_NO_SUSPEND will trigger
WARNINGS because QCA6390 wants to disable the IRQ during the suspend.
To avoid above two issues, QCA6390 driver specifies the irq_flags in case
of one MSI vector when mhi_register_controller is called.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The MHI specification allows to perform a hard reset of the device
when writing to the SOC_RESET register. It can be used to completely
restart the device (e.g. in case of unrecoverable MHI error).
This is up to the MHI controller driver to determine when this hard
reset should be used, and in case of MHI errors, should be used as
a reset of last resort (after standard MHI stack reset).
This function is a stateless function, the MHI layer do nothing except
triggering the reset by writing into the right register(s), this is up
to the caller to ensure right mhi_controller state (e.g. unregister the
controller if necessary).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
