Commit 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_ids are
missing for the dataflash driver and the following warnings are now
seen.
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,at45
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,dataflash
Fix this by adding the necessary spi_device_ids.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211130112443.107730-1-jonathanh@nvidia.com
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
When the NV-DDR interface is not supported by the NAND chip,
the value of onfi->nvddr_timing_modes is 0. In this case,
the best_mode variable value in nand_choose_best_nvddr_timings()
is -1. The last for-loop is skipped and the function returns an
uninitialized value.
If this returned value is 0, the nand_choose_best_sdr_timings()
is not executed and no 'best timing' are set. This leads the host
controller and the NAND chip working at default mode 0 timing
even if a better timing can be used.
Fix this uninitialized returned value.
nand_choose_best_sdr_timings() is pretty similar to
nand_choose_best_nvddr_timings(). Even if onfi->sdr_timing_modes
should never be seen as 0, nand_choose_best_sdr_timings() returned
value is fixed.
Fixes: a9ecc8c814 ("mtd: rawnand: Choose the best timings, NV-DDR included")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-3-herve.codina@bootlin.com
Pull more block driver updates from Jens Axboe:
- Last series adding error handling support for add_disk() in drivers.
After this one, and once the SCSI side has been merged, we can
finally annotate add_disk() as must_check. (Luis)
- bcache fixes (Coly)
- zram fixes (Ming)
- ataflop locking fix (Tetsuo)
- nbd fixes (Ye, Yu)
- MD merge via Song
- Cleanup (Yang)
- sysfs fix (Guoqing)
- Misc fixes (Geert, Wu, luo)
* tag 'for-5.16/drivers-2021-11-09' of git://git.kernel.dk/linux-block: (34 commits)
bcache: Revert "bcache: use bvec_virt"
ataflop: Add missing semicolon to return statement
floppy: address add_disk() error handling on probe
ataflop: address add_disk() error handling on probe
block: update __register_blkdev() probe documentation
ataflop: remove ataflop_probe_lock mutex
mtd/ubi/block: add error handling support for add_disk()
block/sunvdc: add error handling support for add_disk()
z2ram: add error handling support for add_disk()
nvdimm/pmem: use add_disk() error handling
nvdimm/pmem: cleanup the disk if pmem_release_disk() is yet assigned
nvdimm/blk: add error handling support for add_disk()
nvdimm/blk: avoid calling del_gendisk() on early failures
nvdimm/btt: add error handling support for add_disk()
nvdimm/btt: use goto error labels on btt_blk_init()
loop: Remove duplicate assignments
drbd: Fix double free problem in drbd_create_device
nvdimm/btt: do not call del_gendisk() if not needed
bcache: fix use-after-free problem in bcache_device_free()
zram: replace fsync_bdev with sync_blockdev
...
Pull mtd updates from Miquel Raynal:
"Core:
- Remove obsolete macros only used by the old nand_ecclayout struct
- Don't remove debugfs directory if device is in use
- MAINTAINERS:
- Add entry for Qualcomm NAND controller driver
- Update the devicetree documentation path of hyperbus
MTD devices:
- block2mtd:
- Add support for an optional custom MTD label
- Minor refactor to avoid hard coded constant
- mtdswap: Remove redundant assignment of pointer eb
CFI:
- Fixup CFI on ixp4xx
Raw NAND controller drivers:
- Arasan:
- Prevent an unsupported configuration
- Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd,
AMS-Delta:
- Keep the driver compatible with on-die ECC engines
- cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
- Fsmc: Fix use of SM ORDER
- Intel:
- Fix potential buffer overflow in probe
- xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk,
hisi504, gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand drivers:
- Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
- Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
SPI NOR core:
- Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers:
- Enable locking for n25q128a13
SPI NOR controller drivers:
- Use devm_platform_ioremap_resource_byname()"
* tag 'mtd/for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (50 commits)
mtd: core: don't remove debugfs directory if device is in use
MAINTAINERS: Update the devicetree documentation path of hyperbus
mtd: block2mtd: add support for an optional custom MTD label
mtd: block2mtd: minor refactor to avoid hard coded constant
mtd: fixup CFI on ixp4xx
mtd: rawnand: arasan: Prevent an unsupported configuration
MAINTAINERS: Add entry for Qualcomm NAND controller driver
mtd: rawnand: hynix: Add support for H27UCG8T2ETR-BC MLC NAND
mtd: rawnand: xway: Keep the driver compatible with on-die ECC engines
mtd: rawnand: socrates: Keep the driver compatible with on-die ECC engines
mtd: rawnand: plat_nand: Keep the driver compatible with on-die ECC engines
mtd: rawnand: pasemi: Keep the driver compatible with on-die ECC engines
mtd: rawnand: orion: Keep the driver compatible with on-die ECC engines
mtd: rawnand: mpc5121: Keep the driver compatible with on-die ECC engines
mtd: rawnand: gpio: Keep the driver compatible with on-die ECC engines
mtd: rawnand: au1550nd: Keep the driver compatible with on-die ECC engines
mtd: rawnand: ams-delta: Keep the driver compatible with on-die ECC engines
Revert "mtd: rawnand: cs553x: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: lpc32xx_slc: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: ndfc: Fix external use of SW Hamming ECC helper"
...
SPI NOR core changes:
- Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers changes:
- Enable locking for n25q128a13
SPI NOR controller drivers changes:
- Use devm_platform_ioremap_resource_byname()
Core:
* Remove obsolete macros only used by the old nand_ecclayout struct
* MAINTAINERS: Add entry for Qualcomm NAND controller driver
Raw NAND controller drivers:
* Arasan:
- Prevent an unsupported configuration
* Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd, AMS-Delta:
- Keep the driver compatible with on-die ECC engines
* cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
* Fsmc: Fix use of SM ORDER
* Intel:
- Fix potential buffer overflow in probe
* xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk, hisi504,
gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand driver:
* Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
* Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
Merge misc updates from Andrew Morton:
"257 patches.
Subsystems affected by this patch series: scripts, ocfs2, vfs, and
mm (slab-generic, slab, slub, kconfig, dax, kasan, debug, pagecache,
gup, swap, memcg, pagemap, mprotect, mremap, iomap, tracing, vmalloc,
pagealloc, memory-failure, hugetlb, userfaultfd, vmscan, tools,
memblock, oom-kill, hugetlbfs, migration, thp, readahead, nommu, ksm,
vmstat, madvise, memory-hotplug, rmap, zsmalloc, highmem, zram,
cleanups, kfence, and damon)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (257 commits)
mm/damon: remove return value from before_terminate callback
mm/damon: fix a few spelling mistakes in comments and a pr_debug message
mm/damon: simplify stop mechanism
Docs/admin-guide/mm/pagemap: wordsmith page flags descriptions
Docs/admin-guide/mm/damon/start: simplify the content
Docs/admin-guide/mm/damon/start: fix a wrong link
Docs/admin-guide/mm/damon/start: fix wrong example commands
mm/damon/dbgfs: add adaptive_targets list check before enable monitor_on
mm/damon: remove unnecessary variable initialization
Documentation/admin-guide/mm/damon: add a document for DAMON_RECLAIM
mm/damon: introduce DAMON-based Reclamation (DAMON_RECLAIM)
selftests/damon: support watermarks
mm/damon/dbgfs: support watermarks
mm/damon/schemes: activate schemes based on a watermarks mechanism
tools/selftests/damon: update for regions prioritization of schemes
mm/damon/dbgfs: support prioritization weights
mm/damon/vaddr,paddr: support pageout prioritization
mm/damon/schemes: prioritize regions within the quotas
mm/damon/selftests: support schemes quotas
mm/damon/dbgfs: support quotas of schemes
...
Previously, if del_mtd_device() failed with -EBUSY due to a non-zero
usecount, a subsequent call to attempt the deletion again would try to
remove a debugfs directory that had already been removed and panic.
With this change the second call can instead proceed safely.
Fixes: e8e3edb95c ("mtd: create per-device and module-scope debugfs entries")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211014203953.5424-1-zev@bewilderbeest.net
This patch adds support for an optional MTD label for mtd2block emulated
MTD devices. Useful when, e.g., testing device images using Qemu.
The following line in /etc/fstab can then be used to mount a file system
regardless if running on an embedded system, or emulated with block2mtd:
mtd:Config /mnt jffs2 noatime,nodiratime 0 0
Kernel command line syntax in the emulated case:
block2mtd.block2mtd=/dev/sda,,Config
Notice the ',,' it is the optional erase_size, which like before this
patch, defaults to PAGE_SIZE when omitted. Hence the strlen() check.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211009060955.552636-3-troglobit@gmail.com
drivers/mtd/maps/ixp4xx.c requires MTD_CFI_BE_BYTE_SWAP to be set
in order to compile.
drivers/mtd/maps/ixp4xx.c:57:4: error: #error CONFIG_MTD_CFI_BE_BYTE_SWAP required
This patch avoids the #error output by enforcing the policy in
Kconfig. Not sure if this is the right approach, but it helps doing
randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210927141045.1597593-1-arnd@kernel.org
Under the following conditions:
* after rounding up by 4 the number of bytes to transfer (this is
related to the controller's internal constraints),
* if this (rounded) amount of data is situated beyond the end of the
device,
* and only in NV-DDR mode,
the Arasan NAND controller timeouts.
This currently can happen in a particular helper used when picking
software ECC algorithms. Let's prevent this situation by refusing to use
the NV-DDR interface with software engines.
Fixes: 4edde60314 ("mtd: rawnand: arasan: Support NV-DDR interface")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211008163640.1753821-1-miquel.raynal@bootlin.com
Add support for the H27UCG8T2ETR-BC MLC NAND. The NAND is used widely
in the NTC CHIP, is an MLC type NAND, and is 8GB in size. Neither
JEDEC nor ONFI detection identifies it correctly, so the ID is added
to the nand_ids.c file. Additionally, per the datasheet this NAND
appears to use the same paired pages scheme as the Toshiba
TC58TEG5DCLTA00 (dist3), so add support for that to enable use in
SLC emulation mode.
Tested on a NTC CHIP the device is able to write to a ubifs formatted
partition, and then have U-Boot (with proposed patches) boot from a
kernel located on that ubifs formatted partition.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210930162402.344-1-macroalpha82@gmail.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5b ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6a ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
