TUSB320L is a newer chip with additional features, and it has additional steps
in its mode changing sequence:
- Disable CC state machine,
- Write to mode register,
- Wait for 5 ms,
- Re-enable CC state machine.
It also has an additional register that a revision number can be read from.
Add support for the mode changing sequence, and read the revision number during
probe and print it as info.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reset the chip and set its mode to default (maintain mode set by PORT pin)
during probe to make sure it comes up in the default state.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
use low level P-Unit semaphore lock for axp288 register
accesses directly and for more than one access a time,
to reduce the number of times this semaphore is locked
and released which is an expensive operation.
i2c-bus to the XPower is shared between the kernel and the
SoCs P-Unit. The P-Unit has a semaphore wich the kernel must
lock for axp288 register accesses. When the P-Unit semaphore
is locked CPU and GPU power states cannot change or the system
will freeze.
The P-Unit semaphore lock is already managed inside the regmap
access logic, but for each access the semaphore is locked and
released. So use directly iosf_mbi_(un)block_punit_i2c_access(),
we are safe in doing so because nested calls to the same
semaphore are turned to nops.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The USB GPIO extcon driver does not use any of the legacy
includes <linux/gpio.h> or <linux/of_gpio.h> but
exploits the fact that this brings in <linux/mod_device_table.h>.
Fix this up by using the right includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
SM5504 is another MUIC from Silicon Mitus that is fairly similar
to SM5502. They seem to use the same register set, but:
- SM5504 has some additional bits in SM5502_REG_CONTROL
- SM5504 has a quite different set of interrupts
- SM5504 reports USB OTG as dev_type1 = BIT(0) instead of BIT(7)
Overall it's minor and we can support this by defining a separate
struct sm5502_type for SM5504.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Prepare for supporting SM5504 in the extcon-sm5502 driver by replacing
enum sm5504_types with a struct sm5504_type that stores the chip-specific
definitions. This struct can then be defined separately for SM5504
without having to add if (type == TYPE_SM5504) everywhere in the code.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
sm5022_muic_i2c_probe() does not use the i2c_device_id,
so implement i2c_driver->probe_new() instead of probe().
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Use devm_regmap_add_irq_chip() to avoid having to remove the
irqchip explicitly in sm5502_muic_i2c_remove().
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The platform device driver name is "max8997-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
Fixes: b76668ba8a ("Extcon: add MAX8997 extcon driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When sm5502_init_dev_type() iterates over sm5502_reg_data to
initialize the registers it is limited by ARRAY_SIZE(sm5502_reg_data).
There is no need to add another empty element to sm5502_reg_data.
Having the additional empty element in sm5502_reg_data will just
result in writing 0xff to register 0x00, which does not really
make sense.
Fixes: 914b881f94 ("extcon: sm5502: Add support new SM5502 extcon device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon driver for Basin Cove PMIC shadows the switch status used for dwc3
DRD to detect a change in the switch position. This change initializes the
status at probe time.
Cc: stable@vger.kernel.org
Fixes: 492929c547 ("extcon: mrfld: Introduce extcon driver for Basin Cove PMIC")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The extcon IRQ schedules a work item. IRQ is requested using devm while
WQ is cancelld at remove(). This mixing of devm and manual unwinding has
potential case where the WQ has been emptied (.remove() was ran) but
devm unwinding of IRQ was not yet done. It may be possible the IRQ is
triggered at this point scheduling new work item to the already flushed
queue.
According to the input documentation the input device allocated by
devm_input_allocate_device() does not need to be explicitly unregistered.
Use the new devm_work_autocancel() and remove the remove() to simplify the
code.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/cbe8205eed8276f6e6db5003cfe51b8b0d4ac966.1623146580.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core changes for 5.13-rc1.
Nothing major, just lots of little core changes and cleanups, notable
things are:
- finally set 'fw_devlink=on' by default.
All reported issues with this have been shaken out over the past 9
months or so, but we will be paying attention to any fallout here
in case we need to revert this as the default boot value (symptoms
of problems are a simple lack of booting)
- fixes found to be needed by fw_devlink=on value in some subsystems
(like clock).
- delayed work initialization cleanup
- driver core cleanups and minor updates
- software node cleanups and tweaks
- devtmpfs cleanups
- minor debugfs cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (53 commits)
devm-helpers: Fix devm_delayed_work_autocancel() kerneldoc
PM / wakeup: use dev_set_name() directly
software node: Allow node addition to already existing device
kunit: software node: adhear to KUNIT formatting standard
node: fix device cleanups in error handling code
kobject_uevent: remove warning in init_uevent_argv()
debugfs: Make debugfs_allow RO after init
Revert "driver core: platform: Make platform_get_irq_optional() optional"
media: ipu3-cio2: Switch to use SOFTWARE_NODE_REFERENCE()
software node: Introduce SOFTWARE_NODE_REFERENCE() helper macro
software node: Imply kobj_to_swnode() to be no-op
software node: Deduplicate code in fwnode_create_software_node()
software node: Introduce software_node_alloc()/software_node_free()
software node: Free resources explicitly when swnode_register() fails
debugfs: drop pointless nul-termination in debugfs_read_file_bool()
driver core: add helper for deferred probe reason setting
driver core: Improve fw_devlink & deferred_probe_timeout interaction
of: property: fw_devlink: Add support for remote-endpoint
driver core: platform: Make platform_get_irq_optional() optional
driver core: Replace printf() specifier and drop unneeded casting
...
In it's curent state this driver ignores OTG adapters with ID pin
connected to ground. This commit adds a check to set extcon into
host mode when such OTG adapter is connected.
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This allows the MAX8997 charger to set the current limit depending on
the detected extcon charger type.
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Few drivers implement remove call-back only for ensuring a delayed
work gets cancelled prior driver removal. Clean-up these by switching
to use devm_delayed_work_autocancel() instead.
Additionally, this helps avoiding mixing devm and manual resource
management and cleans up a (theoretical?) bug from extconn-palmas.c
and extcon-qcom-spmi-misc.c where (devm managed)IRQ might schedule
new work item after wq was cleaned at remove().
This change is compile-tested only. All testing is appreciated.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/b1030eddbf0069f2d39e951be1d8e40d6413aeeb.1616506559.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The jack handling for arizona codecs is being refactored so that it is
done directly by the codec drivers, instead of having an extcon-driver
bind to a separate "arizona-extcon" child-device for this.
drivers/mfd/arizona-core.c has already been updated to no longer
instantiate an "arizona-extcon" child-device for the arizona codecs.
This means that the "arizona-extcon" driver is no longer useful
(there are no longer any devices for it to bind to).
This commit drops the extcon Kconfig / Makefile bits and moves
drivers/extcon/extcon-arizona.c to sound/soc/codecs/arizona-jack.c .
This is a preparation patch for converting the arizona extcon-driver into
a helper library for letting the arizona codec-drivers directly report jack
state through the standard sound/soc/soc-jack.c functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
