* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (63 commits)
dmaengine: mid_dma: mask_peripheral_interrupt only when dmac is idle
dmaengine/ep93xx_dma: add module.h include
pch_dma: Reduce wasting memory
pch_dma: Fix suspend issue
dma/timberdale: free_irq() on an error path
dma: shdma: transfer based runtime PM
dmaengine: shdma: protect against the IRQ handler
dmaengine i.MX DMA/SDMA: add missing include of linux/module.h
dmaengine: delete redundant chan_id and chancnt initialization in dma drivers
dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_pool
dmaengine/amba-pl08x: Add support for sg len greater than one for slave transfers
serial: sh-sci: don't filter on DMA device, use only channel ID
ARM: SAMSUNG: Remove Samsung specific enum type for dma direction
ASoC: Samsung: Update DMA interface
spi/s3c64xx: Merge dma control code
spi/s3c64xx: Add support DMA engine API
ARM: SAMSUNG: Remove S3C-PL330-DMA driver
ARM: S5P64X0: Use generic DMA PL330 driver
ARM: S5PC100: Use generic DMA PL330 driver
ARM: S5PV210: Use generic DMA PL330 driver
...
Fix up fairly trivial conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
- arch/arm/mach-s5p64x0/dma.c
This adds devicetree binding support to the ARM pl061 driver removing the
platform_data dependency. When DT binding is used, the gpio numbering is
assigned dynamically. For now, interrupts are not supported with DT until
irqdomains learn dynamic irq assignment.
Rather than add another case of -1, updating the driver to use NO_IRQ.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Untill now, sg_len greater than one is not supported. This patch adds support to
do that.
Note: Still, if peripheral is flow controller, sg_len can't be greater that one.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
At least, on SPEAr platforms there is one peripheral, JPEG, which can be flow
controller for DMA transfer. Currently DMA controller driver didn't support
peripheral flow controller configurations.
This patch adds device_fc field in struct pl08x_channel_data, which will be used
only for slave transfers and is not used in case of mem2mem transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pl080 Manual says: "Bursts do not cross the 1KB address boundary"
We can program the controller to cross 1 KB boundary on a burst and controller
can take care of this boundary condition by itself.
Following is the discussion with ARM Technical Support Guys (David):
[Viresh] Manual says: "Bursts do not cross the 1KB address boundary"
What does that actually mean? As, Maximum size transferable with a single LLI is
4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst
size, we can't use this big of an LLI.
[David] There is a difference between bursts describing the total data
transferred by the DMA controller and AHB bursts. Bursts described by the
programmable parameters in the PL080 have no direct connection with the bursts
that are seen on the AHB bus.
The statement that "Bursts do not cross the 1KB address boundary" in the TRM is
referring to AHB bursts, where this limitation is a requirement of the AHB spec.
You can still issue bursts within the PL080 that are in excess of 1KB. The
PL080 will make sure that its bursts are broken down into legal AHB bursts which
will be formatted to ensure that no AHB burst crosses a 1KB boundary.
Based on above discussion, this patch removes all code related to 1 KB boundary
as we are not required to handle this in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination cctl values into the channel structure.
This moves us towards being able to avoid a configuration call each
time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination slave address separately into the channel
structure. This moves us towards being able to avoid a configuration
call each time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This workaround aims to break the deadlock situation
which raises during continuous transfer of data for long
duration over uart with hardware flow control. It is
observed that CTS interrupt cannot be cleared in uart
interrupt register (ICR). Hence further transfer over
uart gets blocked.
It is seen that during such deadlock condition ICR
don't get cleared even on multiple write. This leads
pass_counter to decrease and finally reach zero. This
can be taken as trigger point to run this UART_BT_WA.
Workaround backups the register configuration, does soft
reset of UART using BIT-0 of PRCC_K_SOFTRST_SET/CLEAR
registers and restores the registers.
This patch also provides support for uart init and exit
function calls if present.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support pm_ops in the AMBA bus, required to allow drivers to use runtime pm.
The implementation of AMBA bus pm ops is based on the platform bus
implementation.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the bus level code deals with a const id table, we can also
make the ID table in the amba_driver structure also const.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM CLCD PL110 controller in TFT mode provides two output formats
based on whether the controller is in 24bpp mode or not - either 5551
or 888. PL111 augments this with a 444 and 565 modes.
Some implementations provide an external MUX on the PL110 output to
reassign the bits to achieve 565 mode.
Provide a system of capability flags to allow the CLCD driver to work
out what is supported by each panel and board, and therefore which
display formats are permitted.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of matching the entire peripheral ID, match against
just the part number using the amba_xxx() macros.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on a patch from Linus Walleij.
Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface. The changes over Linus' driver are:
- rename txsize_threshold to dmasize_threshold, as this reflects the
purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer. Some DMA controllers
(eg, PL08x) are unable to be configured for scatter DMA and also listen
to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the
final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
its own restrictions on buffer alignment, not the individual DMA engine
users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
causes LBREQ to be asserted for the last seven transfers, rather than
six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
transfer size required to complete the DMA operation.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (63 commits)
ARM: PL08x: cleanup comments
Update CONFIG_MD_RAID6_PQ to CONFIG_RAID6_PQ in drivers/dma/iop-adma.c
ARM: PL08x: fix a warning
Fix dmaengine_submit() return type
dmaengine: at_hdmac: fix race while monitoring channel status
dmaengine: at_hdmac: flags located in first descriptor
dmaengine: at_hdmac: use subsys_initcall instead of module_init
dmaengine: at_hdmac: no need set ACK in new descriptor
dmaengine: at_hdmac: trivial add precision to unmapping comment
dmaengine: at_hdmac: use dma_address to program DMA hardware
pch_dma: support new device ML7213 IOH
ARM: PL08x: prevent dma_set_runtime_config() reconfiguring memcpy channels
ARM: PL08x: allow dma_set_runtime_config() to return errors
ARM: PL08x: fix locking between prepare function and submit function
ARM: PL08x: introduce 'phychan_hold' to hold on to physical channels
ARM: PL08x: put txd's on the pending list in pl08x_tx_submit()
ARM: PL08x: rename 'desc_list' as 'pend_list'
ARM: PL08x: implement unmapping of memcpy buffers
ARM: PL08x: store prep_* flags in async_tx structure
ARM: PL08x: shrink srcbus/dstbus in txd structure
...
