For "unlock" cycles to 16bit devices in 8bit compatibility mode we need
to use the byte addresses 0xaaa and 0x555. These effectively match
the word address 0x555 and 0x2aa, except the latter has its low bit set.
Most chips don't care about the value of the 'A-1' pin in x8 mode,
but some -- like the ST M29W320D -- do. So we need to be careful to
set it where appropriate.
cfi_send_gen_cmd is only ever passed addresses where the low byte
is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are
affected by this patch, by masking in the extra low bit when the device
is known to be in compatibility mode.
[dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa]
v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile
I'm writing this patch way to late at night.
v3: Bring all of the work back into cfi_build_cmd_addr
including calling of map_bankwidth(map) and cfi_interleave(cfi)
So every caller doesn't need to.
v2: Only modified the address if we our device_type is larger than our
bus width.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
They need to be exported, so let's give them less generic-sounding names
while we're at it.
Original export patch, along with the suggestion about the nomenclature,
from Stephen Rothwell.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Timeouts are currently given by the typical operation time times 8.
It works in the general well-behaved case but not when an erase block is
failing. For erase operations, it seems that a failing erase block will
keep the device state machine in erasing state until the vendor
specified maximum timeout period has passed. By this time the driver
would have long since timed out, left erasing state and attempted
further operations which all fail. This patch implements timeouts using
values from the CFI Query structure when available.
The patch also sets a longer timeout for locking operations. The current
value used for locking/unlocking given by 1000000/HZ microseconds is too
short for devices like J3 and J5 Strataflash which have a typical clear
lock-bits time of 0.5 seconds.
Signed-off-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are some CFI chips which require non standard procedures to get
into QRY mode. The possible way to support them would be trying
different modes till QRY will be read. This patch introduce two new
functions qry_mode_on qry_mode_off. qry_mode_on tries different commands
in order switch chip into QRY mode.
So if we have one more "odd" chip - we just could add several lines to
qry_mode_on. Also using these functions remove unnecessary code
duplicaton in porbe procedure.
Currently there are two "odd" cases
1. Some old intel chips which require 0xFF before 0x98
2. ST M29DW chip which requires 0x98 to be sent at 0x555 (according to
CFI should be 0x55)
This patch is partialy based on the patch from Uwe
(see "[PATCH 2/4] [RFC][MTD] cfi_probe: remove Intel chip workaround"
thread )
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Alexander Belyakov <abelyako@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The current style for debug messages is to ensure they're always
parsed by the compiler and then subjected to dead code removal.
That way builds won't break only when debug options get enabled,
which is common when they are stripped out early by CPP.
This patch makes CONFIG_MTD_DEBUG adopt that convention.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current implementation of subpage read feature for NAND has issues with
small page devices. Small page NAND do not support RNDOUT command.
So subpage feature is not applicable for them.
This patch disables support of subpage for small page NAND.
The code is verified on nandsim(SP NAND simulation) and on LP NAND
devices.
Thanks a lot to Artem for finding this issue.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch enables NAND subpage read functionality.
If upper layer drivers are requesting to read non page aligned data NAND
subpage-read functionality reads the only whose ECC regions which include
requested data when original code reads whole page.
This significantly improves performance in many cases.
Here are some digits :
UBI volume mount time
No subpage reads: 5.75 seconds
Subpage read patch: 2.42 seconds
Open/stat time for files on JFFS2 volume:
No subpage read 0m 5.36s
Subpage read 0m 2.88s
Signed-off-by Alexey Korolev <akorolev@infradead.org>
Acked-by: Artem Bityutskiy <dedekind@infradead.org>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Hch asked not to use "unit" for sub-systems, let it be so.
Also some other commentaries modifications.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This changes the MTD core to handle pci_name() now returning a constant
string.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adding the ability to get a physical address from point() in addition
to virtual address. This physical address is required for XIP of
userspace code from flash.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Reviewed-by: Jörn Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This enhances plat-ram to take a map_probes argument in
the platform_data structure which allow plat-ram to support
any direct-mapped device that MTD supports (jedec, cfi, amd ..)
A few items are also fixed:
- Don't panic if probes is 0
- Actually use the partition list that is passed in
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
