Test TIMESTAMPING and TXTIME across UDP / ICMP and IP versions.
Before ICMPv6 support:
# ./tools/testing/selftests/net/cmsg_time.sh
Case ICMPv6 - ts cnt returned '0', expected '2'
Case ICMPv6 - ts0 SCHED returned '', expected 'OK'
Case ICMPv6 - ts0 SND returned '', expected 'OK'
Case ICMPv6 - TXTIME abs returned '', expected 'OK'
Case ICMPv6 - TXTIME rel returned '', expected 'OK'
FAIL - 5/36 cases failed
After:
# ./tools/testing/selftests/net/cmsg_time.sh
OK
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support requesting Tx timestamps:
$ ./cmsg_sender -p i -t -4 $tgt 123 -d 1000
SCHED ts0 61us
SND ts0 1071us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test if setting SO_MARK with setsockopt works and if cmsg
takes precedence over it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new capabilities of cmsg_sender to test ICMP and RAW sockets,
previously only UDP was tested.
Before SO_MARK support was added to ICMPv6:
# ./cmsg_so_mark.sh
Case ICMP rejection returned 0, expected 1
FAIL - 1/12 cases failed
After:
# ./cmsg_so_mark.sh
OK
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support sending fake ICMP(v6) messages and UDP via RAW sockets.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parametrize the code so that it can support UDP and ICMP
sockets in the future, and more cmsg types.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-02-09
We've added 126 non-merge commits during the last 16 day(s) which contain
a total of 201 files changed, 4049 insertions(+), 2215 deletions(-).
The main changes are:
1) Add custom BPF allocator for JITs that pack multiple programs into a huge
page to reduce iTLB pressure, from Song Liu.
2) Add __user tagging support in vmlinux BTF and utilize it from BPF
verifier when generating loads, from Yonghong Song.
3) Add per-socket fast path check guarding from cgroup/BPF overhead when
used by only some sockets, from Pavel Begunkov.
4) Continued libbpf deprecation work of APIs/features and removal of their
usage from samples, selftests, libbpf & bpftool, from Andrii Nakryiko
and various others.
5) Improve BPF instruction set documentation by adding byte swap
instructions and cleaning up load/store section, from Christoph Hellwig.
6) Switch BPF preload infra to light skeleton and remove libbpf dependency
from it, from Alexei Starovoitov.
7) Fix architecture-agnostic macros in libbpf for accessing syscall
arguments from BPF progs for non-x86 architectures,
from Ilya Leoshkevich.
8) Rework port members in struct bpf_sk_lookup and struct bpf_sock to be
of 16-bit field with anonymous zero padding, from Jakub Sitnicki.
9) Add new bpf_copy_from_user_task() helper to read memory from a different
task than current. Add ability to create sleepable BPF iterator progs,
from Kenny Yu.
10) Implement XSK batching for ice's zero-copy driver used by AF_XDP and
utilize TX batching API from XSK buffer pool, from Maciej Fijalkowski.
11) Generate temporary netns names for BPF selftests to avoid naming
collisions, from Hangbin Liu.
12) Implement bpf_core_types_are_compat() with limited recursion for
in-kernel usage, from Matteo Croce.
13) Simplify pahole version detection and finally enable CONFIG_DEBUG_INFO_DWARF5
to be selected with CONFIG_DEBUG_INFO_BTF, from Nathan Chancellor.
14) Misc minor fixes to libbpf and selftests from various folks.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (126 commits)
selftests/bpf: Cover 4-byte load from remote_port in bpf_sk_lookup
bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
libbpf: Fix compilation warning due to mismatched printf format
selftests/bpf: Test BPF_KPROBE_SYSCALL macro
libbpf: Add BPF_KPROBE_SYSCALL macro
libbpf: Fix accessing the first syscall argument on s390
libbpf: Fix accessing the first syscall argument on arm64
libbpf: Allow overriding PT_REGS_PARM1{_CORE}_SYSCALL
selftests/bpf: Skip test_bpf_syscall_macro's syscall_arg1 on arm64 and s390
libbpf: Fix accessing syscall arguments on riscv
libbpf: Fix riscv register names
libbpf: Fix accessing syscall arguments on powerpc
selftests/bpf: Use PT_REGS_SYSCALL_REGS in bpf_syscall_macro
libbpf: Add PT_REGS_SYSCALL_REGS macro
selftests/bpf: Fix an endianness issue in bpf_syscall_macro test
bpf: Fix bpf_prog_pack build HPAGE_PMD_SIZE
bpf: Fix leftover header->pages in sparc and powerpc code.
libbpf: Fix signedness bug in btf_dump_array_data()
selftests/bpf: Do not export subtest as standalone test
bpf, x86_64: Fail gracefully on bpf_jit_binary_pack_finalize failures
...
====================
Link: https://lore.kernel.org/r/20220209210050.8425-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Two subtests in ksyms_module.c are not qualified as static, so these
subtests are exported as standalone tests in tests.h and lead to
confusion for the output of "./test_progs -t ksyms_module".
By using the following command ...
grep "^void \(serial_\)\?test_[a-zA-Z0-9_]\+(\(void\)\?)" \
tools/testing/selftests/bpf/prog_tests/*.c | \
awk -F : '{print $1}' | sort | uniq -c | awk '$1 != 1'
... one finds out that other tests also have a similar problem, so
fix these tests by marking subtests in these tests as static.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20220208065444.648778-1-houtao1@huawei.com
Use the new dscp_t type to replace the fc_tos field of fib_config, to
ensure IPv4 routes aren't influenced by ECN bits when configured with
non-zero rtm_tos.
Before this patch, IPv4 routes specifying an rtm_tos with some of the
ECN bits set were accepted. However they wouldn't work (never match) as
IPv4 normally clears the ECN bits with IPTOS_RT_MASK before doing a FIB
lookup (although a few buggy code paths don't).
After this patch, IPv4 routes specifying an rtm_tos with any ECN bit
set is rejected.
Note: IPv6 routes ignore rtm_tos altogether, any rtm_tos is accepted,
but treated as if it were 0.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new dscp_t type to replace the tos field of struct fib4_rule,
so that fib4-rules consistently ignore ECN bits.
Before this patch, fib4-rules did accept rules with the high order ECN
bit set (but not the low order one). Also, it relied on its callers
masking the ECN bits of ->flowi4_tos to prevent those from influencing
the result. This was brittle and a few call paths still do the lookup
without masking the ECN bits first.
After this patch fib4-rules only compare the DSCP bits. ECN can't
influence the result anymore, even if the caller didn't mask these
bits. Also, fib4-rules now must have both ECN bits cleared or they will
be rejected.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define a dscp_t type and its appropriate helpers that ensure ECN bits
are not taken into account when handling DSCP.
Use this new type to replace the tclass field of struct fib6_rule, so
that fib6-rules don't get influenced by ECN bits anymore.
Before this patch, fib6-rules didn't make any distinction between the
DSCP and ECN bits. Therefore, rules specifying a DSCP (tos or dsfield
options in iproute2) stopped working as soon a packets had at least one
of its ECN bits set (as a work around one could create four rules for
each DSCP value to match, one for each possible ECN value).
After this patch fib6-rules only compare the DSCP bits. ECN doesn't
influence the result anymore. Also, fib6-rules now must have the ECN
bits cleared or they will be rejected.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
"(__LIBBPF_STRICT_LAST - 1) & ~LIBBPF_STRICT_MAP_DEFINITIONS" is wrong
as it is equal to 0 (LIBBPF_STRICT_NONE). Let's use
"LIBBPF_STRICT_ALL & ~LIBBPF_STRICT_MAP_DEFINITIONS" now that the
previous commit makes it possible in libbpf.
Fixes: 93b8952d22 ("libbpf: deprecate legacy BPF map definitions")
Signed-off-by: Mauricio Vásquez <mauricio@kinvolk.io>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220207145052.124421-4-mauricio@kinvolk.io
Some of the tests are using x86_64 ABI-specific syscall entry points
(such as __x64_sys_nanosleep and __x64_sys_getpgid). Update them to use
architecture-dependent syscall entry names.
Also update fexit_sleep test to not use BPF_PROG() so that it is clear
that the syscall parameters aren't being accessed in the bpf prog.
Note that none of the bpf progs in these tests are actually accessing
any of the syscall parameters. The only exception is perfbuf_bench, which
passes on the bpf prog context into bpf_perf_event_output() as a pointer
to pt_regs, but that looks to be mostly ignored.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/e35f7051f03e269b623a68b139d8ed131325f7b7.1643973917.git.naveen.n.rao@linux.vnet.ibm.com
Add a test that checks that pedit adjusts source and destination
addresses of IPv4 and IPv6 packets.
Output example:
$ ./pedit_ip.sh
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: dev swp2 ingress pedit ip src set 198.51.100.1 [ OK ]
TEST: dev swp3 egress pedit ip src set 198.51.100.1 [ OK ]
TEST: dev swp2 ingress pedit ip dst set 198.51.100.1 [ OK ]
TEST: dev swp3 egress pedit ip dst set 198.51.100.1 [ OK ]
TEST: dev swp2 ingress pedit ip6 src set 2001:db8:2::1 [ OK ]
TEST: dev swp3 egress pedit ip6 src set 2001:db8:2::1 [ OK ]
TEST: dev swp2 ingress pedit ip6 dst set 2001:db8:2::1 [ OK ]
TEST: dev swp3 egress pedit ip6 dst set 2001:db8:2::1 [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added a command line option '-i' for mptcp_join.sh to use
'ip mptcp' commands instead of using 'pm_nl_ctl' commands to deal with
PM netlink.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the setting flags test cases, using both addr-based and
id-based lookups for the setting address.
The output looks like this:
set flags (backup) [ OK ]
(nobackup) [ OK ]
(fullmesh) [ OK ]
(nofullmesh) [ OK ]
(backup,fullmesh) [ OK ]
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the id argument for setting the address flags in
pm_nl_ctl.
Usage:
pm_nl_ctl set id 1 flags backup
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
