This update adds a debugfs interface to modify a pin configuration
for a given state in the pinctrl map. This allows to modify the
configuration for a non-active state, typically sleep state.
This configuration is not applied right away, but only when the state
will be entered.
This solution is mandated for us by HW validation: in order
to test and verify several pin configurations during sleep without
recompiling the software.
Change log in this patch set;
Take into account latest feedback from Stephen Warren:
- stale comments update
- improved code efficiency and readibility
- limit size of global variable pinconf_dbg_conf
- remove req_type as it can easily be added later when
add/delete requests support is implemented
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename PIN_CONFIG_INPUT_SCHMITT_DISABLE to
PIN_CONFIG_INPUT_SCHMITT_ENABLE. It's used to make it more generialize.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the device core auto-grab the pinctrl handle and set
the "default" (PINCTRL_STATE_DEFAULT) state for every device
that is present in the device model right before probe. This will
account for the lion's share of embedded silicon devcies.
A modification of the semantics for pinctrl_get() is also done:
previously if the pinctrl handle for a certain device was already
taken, the pinctrl core would return an error. Now, since the
core may have already default-grabbed the handle and set its
state to "default", if the handle was already taken, this will
be disregarded and the located, previously instanitated handle
will be returned to the caller.
This way all code in drivers explicitly requesting their pinctrl
handlers will still be functional, and drivers that want to
explicitly retrieve and switch their handles can still do that.
But if the desired functionality is just boilerplate of this
type in the probe() function:
struct pinctrl *p;
p = devm_pinctrl_get_select_default(&dev);
if (IS_ERR(p)) {
if (PTR_ERR(p) == -EPROBE_DEFER)
return -EPROBE_DEFER;
dev_warn(&dev, "no pinctrl handle\n");
}
The discussion began with the addition of such boilerplate
to the omap4 keypad driver:
http://marc.info/?l=linux-input&m=135091157719300&w=2
A previous approach using notifiers was discussed:
http://marc.info/?l=linux-kernel&m=135263661110528&w=2
This failed because it could not handle deferred probes.
This patch alone does not solve the entire dilemma faced:
whether code should be distributed into the drivers or
if it should be centralized to e.g. a PM domain. But it
solves the immediate issue of the addition of boilerplate
to a lot of drivers that just want to grab the default
state. As mentioned, they can later explicitly retrieve
the handle and set different states, and this could as
well be done by e.g. PM domains as it is only related
to a certain struct device * pointer.
ChangeLog v4->v5 (Stephen):
- Simplified the devicecore grab code.
- Deleted a piece of documentation recommending that pins
be mapped to a device rather than hogged.
ChangeLog v3->v4 (Linus):
- Drop overzealous NULL checks.
- Move kref initialization to pinctrl_create().
- Seeking Tested-by from Stephen Warren so we do not disturb
the Tegra platform.
- Seeking ACK on this from Greg (and others who like it) so I
can merge it through the pinctrl subsystem.
ChangeLog v2->v3 (Linus):
- Abstain from using IS_ERR_OR_NULL() in the driver core,
Russell recently sent a patch to remove it. Handle the
NULL case explicitly even though it's a bogus case.
- Make sure we handle probe deferral correctly in the device
core file. devm_kfree() the container on error so we don't
waste memory for devices without pinctrl handles.
- Introduce reference counting into the pinctrl core using
<linux/kref.h> so that we don't release pinctrl handles
that have been obtained for two or more places.
ChangeLog v1->v2 (Linus):
- Only store a pointer in the device struct, and only allocate
this if it's really used by the device.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Mitch Bradley <wmb@firmworks.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Rickard Andersson <rickard.andersson@stericsson.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[swarren: fixed and simplified error-handling in pinctrl_bind_pins(), to
correctly handle deferred probe. Removed admonition from docs not to use
pinctrl hogs for devices]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add new function to get devname from pinctrl_dev. pinctrl_dev_get_name()
can only get pinctrl description name. If we want to use gpio driver to
find pinctrl device node, we need to fetch the pinctrl device name.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pin configurations IP allows to set the current output to the pin.
This patch adds such a parameter to the pinconf-generic mechanism.
This parameter takes as argument the drive strength in mA.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a definition of a generic output configuration
for a certain pin when using the generic pin configuration
library. Whereas driving pins low/high is usually a GPIO
business, you may want to set up pins into a default state
using hogs, and never touch them again. This helps out
with that scenario.
Based on a patch from Patrice Chotard.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In Marvell PXA/MMP silicons, input schmitt disable value is 0x40, not 0.
So append new config parameter -- input schmitt disable.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a function to the pinctrl core to retrieve the GPIO
range associated with a certain pin for a certain controller.
This is needed when a pinctrl driver want to look up the
corresponding struct gpio_chip for a certain pin. As the
GPIO drivers can now create these ranges themselves, the
pinctrl driver no longer knows about all its associated GPIO
chips.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the function find_pinctrl_and_add_gpio_range()
to pinctrl_find_and_add_gpio_range() so as to be consistent
with the rest of the functions.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The fact that of_gpiochip_add_pin_range() and
gpiochip_add_pin_range() share too much code is fragile and
will invariably mean that bugs need to be fixed in two places
instead of one.
So separate the concerns of gpiolib.c and gpiolib-of.c and
have the latter call the former as back-end. This is necessary
also when going forward with other device descriptions such
as ACPI.
This is done by:
- Adding a return code to gpiochip_add_pin_range() so we can
reliably check whether this succeeds.
- Get rid of the custom of_pinctrl_add_gpio_range() from
pinctrl. Instead create of_pinctrl_get() to just retrive the
pin controller per se from an OF node. This composite
function was just begging to be deleted, it was way to
purpose-specific.
- Use pinctrl_dev_get_name() to get the name of the retrieved
pin controller and use that to call back into the generic
gpiochip_add_pin_range().
Now the pin range is only allocated and tied to a pin
controller from the core implementation in gpiolib.c.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl subsystem needs gpio chip base to prepare set of gpio
pin ranges, which a given pinctrl driver can handle. This is
important to handle pinctrl gpio request calls in order to
program a given pin properly for gpio operation.
As gpio base is allocated dynamically during gpiochip
registration, presently there exists no clean way to pass this
information to the pinctrl subsystem.
After few discussions from [1], it was concluded that may be
gpio controller reporting the pin range it supports, is a
better way than pinctrl subsystem directly registering it.
[1] http://comments.gmane.org/gmane.linux.ports.arm.kernel/184816
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
[Edited documentation a bit]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts earlier commit which removed
pinctrl_remove_gpio_range(), because at that time there
weren't any more users of that routine. It was removed as the
removal of ranges was done in unregister of pinctrl.
But as we are now registering stuff from gpiolib, we may
remove and insert a gpio module multiple times. So, we
need this routine again.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull preparatory patches for user API disintegration from David Howells:
"The patches herein prepare for the extraction of the Userspace API
bits from the various header files named in the Kbuild files.
New subdirectories are created under either include/uapi/ or
arch/x/include/uapi/ that correspond to the subdirectory containing
that file under include/ or arch/x/include/.
The new subdirs under the uapi/ directory are populated with Kbuild
files that mostly do nothing at this time. Further patches will
disintegrate the headers in each original directory and fill in the
Kbuild files as they do it.
These patches also:
(1) fix up #inclusions of "foo.h" rather than <foo.h>.
(2) Remove some redundant #includes from the DRM code.
(3) Make the kernel build infrastructure handle Kbuild files both in
the old places and the new UAPI place that both specify headers
to be exported.
(4) Fix some kernel tools that #include kernel headers during their
build.
I have compile tested this with allyesconfig against x86_64,
allmodconfig against i386 and a scattering of additional defconfigs of
other arches. Prepared for main script
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>"
* tag 'uapi-prep-20121002' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Plumb the UAPI Kbuilds into the user header installation and checking
UAPI: x86: Differentiate the generated UAPI and internal headers
UAPI: Remove the objhdr-y export list
UAPI: Move linux/version.h
UAPI: Set up uapi/asm/Kbuild.asm
UAPI: x86: Fix insn_sanity build failure after UAPI split
UAPI: x86: Fix the test_get_len tool
UAPI: (Scripted) Set up UAPI Kbuild files
UAPI: Partition the header include path sets and add uapi/ header directories
UAPI: (Scripted) Convert #include "..." to #include <path/...> in kernel system headers
UAPI: (Scripted) Convert #include "..." to #include <path/...> in drivers/gpu/
UAPI: (Scripted) Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
UAPI: Refer to the DRM UAPI headers with <...> and from certain headers only
This pure documentation fix tries to align the "idle" and
"sleep" pin states to the idle and suspend states from
runtime PM.
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As struct device is used as a function argument, it should at
least be declared (device.h is not included).
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ux500 GPIO and pinctrl changes for kernel 3.5
* tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
pinctrl: add sleep state definition
pinctrl/nomadik: implement pin configuration
pinctrl/nomadik: implement pin multiplexing
pinctrl/nomadik: reuse GPIO debug function for pins
pinctrl/nomadik: break out single GPIO debug function
pinctrl/nomadik: basic Nomadik pinctrl interface
pinctrl/nomadik: !CONFIG_OF build error
gpio: move the Nomadik GPIO driver to pinctrl
Context conflicts resolved in drivers/pinctrl/Kconfig and
drivers/pinctrl/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
There is an IDLE definition in the pinctrl framework, but for
ux500 SLEEP is more apropriate.
I've added some comments on the semantics of the common states
so as to avoid misunderstandings.
ChangeLog v1->v2:
- Fixed terminology "on"->"into".
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes a repeated word and a repeated and incomplete line from two
pinctrl headers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a interface pinctrl_provide_dummies for platform to indicate
whether it needs use pinctrl dummy state.
ChangeLog v3->v4:
* remove dummy gpio support in pinctrl subsystem.
Let gpio driver decide whether it wants to use pinctrl gpio mux
function.
ChangeLog v2->v3:
* Also changed the missed pinctrl gpio APIs in v1.
ChangeLog v1->v2:
* Based on sascha's suggestion, drop using kconfig since it will hide
pinctrl errors on all other boards.
See: https://lkml.org/lkml/2012/4/18/282
It seemed both Linus and Stephen agreed with this way, so i'm ok
with it too.
* Add dummy gpio support.
pinctrl gpio in the same situation as state.
* Patch name changed.
Original is pinctrl: handle dummy state in core.
* Split removing old dt dummy interface into a separate patch
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
