Spoofcheck can't be enabled if VF MAC is zero.
Vice versa, can't zero MAC if spoofcheck is on.
Fixes: 8f7ba3ca12 ('net/mlx4: Add set VF mac address support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vf to VST 802.1ad mode (mlx4 VST QinQ mode) by setting vf vlan
protocol to 802.1ad.
VST 802.1ad mode in mlx4, is used for STAG strip/insertion by PF, while
the CTAG is set by the VF.
Read current vlan protocol as part of the vf configuration state.
Upon setting vf vlan protocol to 802.1ad, we use a mechanism of handshake
to verify that both the vf and the pf driver version support it.
The handshake uses the command QUERY_FUNC_CAP:
- The vf sets a pre-defined support bit in input modifier.
- A pf that supports the feature sends the request to the vf through a
pre-defined field in the output mailbox.
- In case vf does not support the feature, the pf will fail the control
command (in this case, IP link tool command to set the vf vlan
protocol to 802.1ad).
No change in VST 802.1Q mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To tell hardware about a gid with type RoCEv2, software needs a new
modifier to the SET_PORT command: MLX4_SET_PORT_ROCE_ADDR. This can
replace the old method, MLX4_SET_PORT_GID_TABLE, for RoCEv1 gids.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement the ndo to gather VF statistics through the PF.
All counters related to this VF are stored in a per slave
list, run over the slave's list and collect all statistics.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an infrastructure step for querying VF and PF counters.
This code was in the IB driver, move it to the mlx4 core driver
so it will be accessible for more use cases.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the interface ethtool identify feature.
Make the physical port LED to blink with green and yellow colors.
The device handles the LED blink by itself (synchrous use of
set_phys_id), by returning 0 to ETHTOOL_ID_ACTIVE command.
Signed-off-by: Eyal Grossman <eyalgr@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calls to SET_PORT used hard-code numbers, when supplying command's
opcode modifiers, fix that to use well defined constants.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support granular QoS per VF, by implementing the ndo_set_vf_rate.
Enforce a rate limit per VF when called, and enabled only for VFs in
VST mode with user priority supported by the device.
We don't enforce VFs to be in VST mode at the moment of configuration,
but rather save the given rate limit and enforce it when the VF is
moved to VST with user priority which is supported (currently 0).
VST<->VGT or VST qos value state changes are disallowed when a rate
limit is configured. Minimum BW share is not supported yet.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SET_VPORT_QOS device command, which is ntended for virtual
granular QoS configuration per VF in SRIOV mode. The SET_VPORT_QOS
command sets and queries QoS parameters of a VPort. Each priority
allowed for a VPort is assigned with a share of the BW, and a BW
limitation. QoS parameters can be modified at any time, but must be
initialized before any QP is associated with the VPort.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements device ALLOCATE_VPP command, to be used for granular QoS
configuration of VFs by the PF device. Defines and queries the amount
of VPPs assigned to each port, and the amount of VPPs assigned to each
priority of each port. Once the total VPPs are split between the priorities
of a port, they may be assigned with a share of the BW or a rate limit.
Split into two functions (get/set) whoch are supplied with
mlx4_alloc_vpp_context and physical port number.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device capability, firmware command opcode and etc prior elements
needed for QCN suppprt. Disable SRIOV VF view/access for QCN is disabled.
While here, remove a redundant offset definition into the
QUERY_DEV_CAP mailbox.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the hardware interface required for port aggregation.
1. Disable RX port check on receive - don't perform a validity check
that matches to QP's port and the port where the packet is received.
2. Virtual to physical port remap - configure virtual to physical port
mapping. Port remap capability for virtual functions.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware spec states that the timeout for all commands should be 60 seconds.
In the past, the spec indicated that there were several classes of timeout
(short, medium, and long). The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.
In addition, we fix a few commands which had hard-coded numeric timeouts specified.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV, both the PF and the VF may attempt device recovery whenever they
assume that the device is not functioning. When the PF driver resets the
device, the VF should detect this and attempt to reinitialize itself.
The VF must be able to reset itself under all circumstances, even
if the PF is not responsive.
The VF shall reset itself in the following cases:
1. Commands are not processed within reasonable time over the communication channel.
This is done considering device state and the correct return code based on
the command as was done in the native mode, done in the next patch.
2. The VF driver receives an internal error event reported by the PF on the
communication channel. This occurs when the PF driver resets the device or
when VF is out of sync with the PF.
Add 'VF reset' capability, which allows the VF to reinitialize itself even when the
PF is not responsive.
As PF and VF may run their reset flow simulantanisly, there are several cases
that are handled:
- Prevent freeing VF resources upon FLR, when PF is in its unloading stage.
- Prevent PF getting VF commands before it has finished initializing its resources.
- Upon VF startup, check that comm-channel is online before sending
commands to the PF and getting timed-out.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.
The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.
In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.
The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.
Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to issue CONFIG_DEV "get" firmware command.
This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.
The GET operation is allowed for VFs too.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding ACCESS REG mlx4 command and use it to implement Query method for
PTYS (Port Type and Speed Register).
Query and store eth_prot_ctrl dev cap.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Secure-host is the general term for the capability of a device
to protect itself and the subnet from malicious host software.
This is achieved by:
1. Not allowing un-trusted entities to access device configuration
registers, directly (through pci_cr or pci_conf) and indirectly
(through MADs).
2. Hiding M_Key from untrusted entities.
3. Preventing the modification of GUID0 by un-trusted entities
4. Not allowing drivers on untrusted hosts to receive nor to transmit
packets over QP0 (SMP Firewall).
The secure-host capability depends on firmware handling all QP0
packets, and not passing these packets up to the driver. Any information
required by the driver for proper operation (e.g., SM lid) is passed
via events generated by the firmware while processing QP0 MADs.
Driver support mainly requires using the MAD_DEMUX FW command at startup,
where the feature is enabled/disabled through a procedure described in
the Mellanox HCA tools package.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
[ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This patch adds support for allocating IB UD QPs that we can steer
traffic from. We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.
This command isn't supported for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.
This is done through the following elements:
- read tunneling device caps in QUERY_DEV_CAP
- add helper function to do SET_PORT for tunneling
- add DMFS VXLAN steering rule definitions
- add CQE and WQE checksum offload field definitions
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small code cleanup:
1. change MLX4_DEV_CAP_FLAGS2_REASSIGN_MAC_EN to MLX4_DEV_CAP_FLAG2_REASSIGN_MAC_EN
2. put MLX4_SET_PORT_PRIO2TC and MLX4_SET_PORT_SCHEDULER in the same union with the
other MLX4_SET_PORT_yyy
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds new firmware command and new firmware event. The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.
Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
