* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
To get rid of port expanders, the free GPIOs of ab8500
can be used. There are 42 GPIO pins. Out of which 16
are interrupt capable.This patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[Renamed header file as per MFD structure]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: Add MODULE_DEVICE_TABLE to max8997 and max8998
regulator: fix tps6524x section mismatch
regulator: Remove more wm831x-specific IRQ operations
regulator: add ab8500 enable and raise time delays
regulator: provide consumer interface for fall/rise time
regulator: add set_voltage_time_sel infrastructure
regulator: initialization for ab8500 regulators
regulator: add support for USB voltage regulator
regulator: switch the ab3100 to use enable_time()
Regulator: add suspend-finish API for regulator core.
regulator: fix typo in Kconfig
regulator: Convert WM831x regulators to genirq
regulator: If we fail when setting up a supply say which supply
This patch enables IRQ handling for MAX8997/8966 chips.
Please note that Fuel-Gauge-related IRQs are not implemented in this
initial release. The fuel gauge module in MAX8997 is identical to
MAX17042, which is already in Linux kernel. In order to use the
already-existing MAX17042 driver for fuel gauge module in MAX8997, the
main interrupt handler of MAX8997 should relay related interrupts to
MAX17042 driver. However, in order to do this, we need to modify
MAX17042 driver as well because MAX17042 driver does not have any
interrupt handlers for now. We are not going to implement this in this
initial release as it is not crucial in basic operations of MAX8997.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace mfd_shared_platform_driver_register with mfd_clone_cell. The
former was called by an mfd client, and registered both a platform driver
and device. The latter is called by an mfd driver, and registers only a
platform device.
The downside of this is that mfd drivers need to be modified whenever
new clients are added that share a cell; the upside is that it fits
Linux's driver model better. It's also simpler.
This also converts cs5535-mfd/olpc-xo1 from the old API. cs5535-mfd
now creates the olpc-xo1-{acpi,pms} devices, while olpc-xo1 binds to
them via platform drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The regulators on the AB8500 have a lot of custom
hardware control settings pertaining to 8 external
signals, settings which are board-specific and need
be provided from the platform at startup.
Initialization added for regulators Vana, VextSupply1,
VextSupply2, VextSupply3, Vaux1, Vaux2, Vaux3, VTVout,
Vintcore12, Vaudio, Vdmic, Vamic1, Vamic2, VrefDDR.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
On sh-mobile platforms the SDHI driver was using the tmio_mmc SD/SDIO
MFD cell driver. Now that the tmio_mmc driver has been split into a
core and a separate MFD glue, we can support SDHI natively without the
need to emulate an MFD controller. This also allows to support systems
with an on-SoC SDHI controller and a separate MFD with a TMIO core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Append the additional read/write operation on 88pm860x for accessing
test page in 88PM860x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
regulator driver. So move the identification of device node from
regulator driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
led driver. So move the identification of device node from led
driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
backlight driver. So move the identification of device node from
backlight driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This revamps the interface so that AB8500 GPADCs are fetched by
name. Probed GPADCs are added to a list and this list is searched
for a matching GPADC. This makes it possible to have multiple
AB8500 GPADC instances instead of it being a singleton, and
rids the need to keep a GPADC pointer around in the core AB8500
MFD struct.
Currently the match is made to the device name which is by default
numbered from the device instance such as "ab8500-gpadc.0" but
by using the .init_name field of the device a more intiutive
naming for the GPADC blocks can be achieved if desired.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves the ab8500-gpadc.h header down into the ab8500/
subdir in include/linux/mfd and fixes some whitespace in the
header in the process.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8997/MAX8966 chip is a multi-function device with I2C bussses. The
chip includes PMIC, RTC, Fuel Gauge, MUIC, Haptic, Flash control, and
Battery (charging) control.
This patch is an initial release of a MAX8997/8966 driver that supports
to enable the chip with its primary I2C bus that connects every device
mentioned above except for Fuel Gauge, which uses another I2C bus. The
fuel gauge is not supported by this mfd driver and is supported by a
seperated driver of MAX17042 Fuel Gauge (yes, the fuel gauge part is
compatible with MAX17042).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As requested by Samuel, there's not really any reason to have "shared"
in the name.
This also modifies the only user of the function, as well.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
