While fixing undefined behaviour the commit f60d7270c8 ("spi: Avoid
undefined behaviour when counting unused native CSs") missed the case
when all CSs are GPIOs and thus unused_native_cs will be evaluated to
-1 in unsigned representation. This will falsely trigger a condition
in the spi_get_gpio_descs().
Switch to signed types for *_native_cs SPI controller fields to fix above.
Fixes: f60d7270c8 ("spi: Avoid undefined behaviour when counting unused native CSs")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510131242.49455-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups"
* tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (79 commits)
mmc: block: Issue a cache flush only when it's enabled
memstick: r592: ignore kfifo_out() return code again
mmc: block: Update ext_csd.cache_ctrl if it was written
mmc: mmc_spi: Make of_mmc_spi.c resource provider agnostic
mmc: mmc_spi: Use already parsed IRQ
mmc: mmc_spi: Drop unused NO_IRQ definition
mmc: mmc_spi: Set up polling even if voltage-ranges is not present
mmc: core: Convert mmc_of_parse_voltage() to use device property API
mmc: core: Correct descriptions in mmc_of_parse()
mmc: dw_mmc-rockchip: Just set default sample value for legacy mode
mmc: sdhci-s3c: constify uses of driver/match data
mmc: sdhci-s3c: correct kerneldoc of sdhci_s3c_drv_data
mmc: sdhci-s3c: simplify getting of_device_id match data
mmc: tmio: always restore irq register
mmc: sdhci-pci-gli: Enlarge ASPM L1 entry delay of GL975x
mmc: core: Let eMMC sanitize not retry in case of timeout/failure
mmc: core: Add a retries parameter to __mmc_switch function
memstick: r592: remove unused variable
mmc: sdhci-st: Remove unnecessary error log
mmc: sdhci-msm: Remove unnecessary error log
...
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
The older API used to supply additional device properties for the
devices - so mainly the function device_add_properties() - is going to
be removed. The reason why the API will be removed is because it gives
false impression that the properties are assigned directly to the
devices, which has actually never been the case - the properties have
always been assigned to a software fwnode which was then just directly
linked with the device when the old API was used. By only accepting
device properties instead of complete software nodes, the subsystems
remove any change of taking advantage of the other features the
software nodes have.
The change that is required from the spi subsystem and the drivers is
trivial. Basically only the "properties" member in struct
spi_board_info, which was a pointer to struct property_entry, is
replaced with a pointer to a complete software node.
thanks,
Heikki Krogerus (4):
spi: Add support for software nodes
ARM: pxa: icontrol: Constify the software node
ARM: pxa: zeus: Constify the software node
spi: Remove support for dangling device properties
arch/arm/mach-pxa/icontrol.c | 12 ++++++++----
arch/arm/mach-pxa/zeus.c | 6 +++++-
drivers/spi/spi.c | 21 ++++++---------------
include/linux/spi/spi.h | 7 +++----
4 files changed, 22 insertions(+), 24 deletions(-)
--
2.30.1
base-commit: a38fd87484
Pull backlight updates from Lee Jones:
"New Functionality:
- Convert to GPIO descriptors
Fix-ups:
- Trivial: fix coding style in sky81452-backlight
- Ensure backlight state is known on bring-up in ktd253
- Use common platform API in qcom-wled and fbdev"
* tag 'backlight-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight/video: Use Platform getter/setter functions
backlight: ktd253: Bring up in a known state
backlight: sky81452-backlight: Convert comma to semicolon
backlight: lms283gf05: Convert to GPIO descriptors
Pull spi updates from Mark Brown:
"The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware.
Otherwise mostly thanks to Arnd's cleanup efforts on old platforms
we've removed several obsolete drivers which just about balance out
the newer drivers we've added this cycle.
Summary:
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in
spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolete EFM32, Txx9 and SIRF Prima and Atlas drivers"
* tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (76 commits)
spi: Skip zero-length transfers in spi_transfer_one_message()
spi: dw: Avoid stack content exposure
spi: cadence-quadspi: Use spi_mem_dtr_supports_op()
spi: spi-mem: add spi_mem_dtr_supports_op()
spi: atmel-quadspi: Disable the QSPI IP at suspend()
spi: pxa2xx: Add IDs for the controllers found on Intel Lynxpoint
spi: pxa2xx: Fix the controller numbering for Wildcat Point
spi: Change provied to provided in the file spi.h
spi: mediatek: add set_cs_timing support
spi: support CS timing for HW & SW mode
spi: add power control when set_cs_timing
spi: stm32: make spurious and overrun interrupts visible
spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC
spi: stm32: defer probe for reset
spi: stm32: driver uses reset controller only at init
spi: stm32h7: ensure message are smaller than max size
spi: stm32: use bitfield macros
spi: stm32: do not mandate cs_gpio
spi: stm32: properly handle 0 byte transfer
spi: clps711xx: remove redundant white-space
...
spi_mem_default_supports_op() rejects DTR ops by default to ensure that
the controller drivers that haven't been updated with DTR support
continue to reject them. It also makes sure that controllers that don't
support DTR mode at all (which is most of them at the moment) also
reject them.
This means that controller drivers that want to support DTR mode can't
use spi_mem_default_supports_op(). Driver authors have to roll their own
supports_op() function and mimic the buswidth checks. See
spi-cadence-quadspi.c for example. Or even worse, driver authors might
skip it completely or get it wrong.
Add spi_mem_dtr_supports_op(). It provides a basic sanity check for DTR
ops and performs the buswidth requirement check. Move the logic for
checking buswidth in spi_mem_default_supports_op() to a separate
function so the logic is not repeated twice.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210204141218.32229-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210125150238.16980-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the lms283gf05 backlight driver to use GPIO
descriptors and switches the single PXA Palm Z2 device
over to defining these.
Since the platform data was only used to convey GPIO
information we can delete the platform data header.
Notice that we define the proper active low semantics in
the board file GPIO descriptor table (active low) and
assert the reset line by bringing it to "1" (asserted).
Cc: Marek Vasut <marex@denx.de>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This change moves all the SPI mode bits into a separate 'spi.h' header in
uAPI. This is meant to re-use these definitions inside the kernel as well
as export them to userspace (via uAPI).
The SPI mode definitions have usually been duplicated between between
'include/linux/spi/spi.h' and 'include/uapi/linux/spi/spidev.h', so
whenever adding a new entry, this would need to be put in both headers.
They've been moved from 'include/linux/spi/spi.h', since that seems a bit
more complete; the bits have descriptions and there is the SPI_MODE_X_MASK.
This change also does a conversion of these bitfields to _BITUL() macro.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_controller()
spi_unregister_controller()
That's because spi_unregister_controller() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_controller which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_controller struct. Thus, once spi_unregister_controller()
has been called, the private data is inaccessible. But some drivers
need to access it after spi_unregister_controller() to perform further
teardown steps.
Introduce devm_spi_alloc_master() and devm_spi_alloc_slave(), which
release a reference on the spi_controller struct only after the driver
has unbound, thereby keeping the memory allocation accessible. Change
spi_unregister_controller() to not release a reference if the
spi_controller was allocated by one of these new devm functions.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_controller in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm functions
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the controller.
That commit shall amend spi_unregister_controller() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/272bae2ef08abd21388c98e23729886663d19192.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a macro to filter all SPI_MODE_0,1,2,3 mode in one run.
The latest SPI framework will parse the devicetree in following call
sequence: of_register_spi_device() -> of_spi_parse_dt()
So, driver do not need to pars the devicetree and will get prepared
flags in the probe.
On one hand it is good far most drivers. On other hand some drivers need to
filter flags provide by SPI framework and apply know to work flags. This drivers
may use SPI_MODE_X_MASK to filter MODE flags and set own, known flags:
spi->flags &= ~SPI_MODE_X_MASK;
spi->flags |= SPI_MODE_0;
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201027095724.18654-2-o.rempel@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
