Some of the SoundWire device ports are statically mapped to Controller
ports during design, however there is no way to expose this information
to the controller. Controllers like Qualcomm ones use this info to setup
static bandwidth parameters for those ports.
A generic port allocation is not possible in this cases!
So this patch adds a new member m_port_map to struct sdw_slave to expose
this static map.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210315165650.13392-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently quirks are only allowed for Slave devices. This patch
describes the need for two quirks at the Master level.
a) bus clash
The SoundWire specification allows a Slave device to report a bus clash
with the in-band interrupt mechanism when it detects a conflict while
driving a bitSlot it owns. This can be a symptom of an electrical conflict
or a programming error, and it's vital to detect reliably.
Unfortunately, on some platforms, bus clashes are randomly reported by
Slave devices after a bus reset, with an interrupt status set even before
the bus clash interrupt is enabled. These initial spurious interrupts are
not relevant and should optionally be filtered out, while leaving the
interrupt mechanism enabled to detect 'true' issues.
This patch suggests the addition of a Master level quirk to discard such
interrupts. The quirk should in theory have been added at the Slave level,
but since the problem was detected with different generations of Slave
devices it's hard to point to a specific IP. The problem might also be
board-dependent and hence dealing with a Master quirk is simpler.
b) parity
Additional tests on a new platform with the Maxim 98373 amplifier
showed a rare case where the parity interrupt is also thrown on
startup, at the same time as bus clashes. This issue only seems to
happen infrequently and was only observed during suspend-resume stress
tests while audio is streaming. We could make the problem go away by
adding a Slave-level quirk, but there is no evidence that the issue is
actually a Slave problem: the parity is provided by the Master, which
could also set an invalid parity in corner cases.
BugLink: https://github.com/thesofproject/linux/issues/2578
BugLink: https://github.com/thesofproject/linux/issues/2533
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210302082720.12322-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ACPI scan capabilities is called from the intel-dspconfig as well
as the SOF/HDaudio drivers. This creates dependencies and randconfig issues
when HDaudio and SOF/SoundWire are not all configured as modules.
To simplify Kconfig dependencies between HDAudio, SoundWire, SOF and
intel-dspconfig, move the ACPI scan helpers to a dedicated
module. This follows the same idea as NHLT helpers which are already
handled as a dedicated module.
The only functional change is that the kernel parameter to filter
links is now handled by a different module, but that was only provided
for developers needing work-arounds for early BIOS releases.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
The upcoming SDCA (SoundWire Device Class Audio) specification defines
a hierarchical encoding to interface with Class-defined capabilities.
The specification is not yet accessible to the general public but this
information is released with explicit permission from the MIPI Board
to avoid delays with SDCA support on Linux platforms.
A block of 64 MBytes of register addresses are allocated to SDCA
controls, starting at address 0x40000000. The 26 LSBs which identify
individual controls are set based on the following variables:
- Function Number. An SCDA device can be split in up to 8 independent
Functions. Each of these Functions is described in the SDCA
specification, e.g. Smart Amplifier, Smart Microphone, Simple
Microphone, Jack codec, HID, etc.
- Entity Number. Within each Function, an Entity is an identifiable
block. Up to 127 Entities are connected in a pre-defined
graph (similar to USB), with Entity0 reserved for Function-level
configurations. In contrast to USB, the SDCA spec pre-defines
Function Types, topologies, and allowed options, i.e. the degree of
freedom is not unlimited to limit the possibility of errors in
descriptors leading to software quirks.
- Control Selector. Within each Entity, the SDCA specification defines
48 controls such as Mute, Gain, AGC, etc, and 16 implementation
defined ones. Some Control Selectors might be used for low-level
platform setup, and other exposed to applications and users. Note
that the same Control Selector capability, e.g. Latency control,
might be located at different offsets in different entities, the
Control Selector mapping is Entity-specific.
- Control Number. Some Control Selectors allow channel-specific values
to be set, with up to 64 channels allowed. This is mostly used for
volume control.
- Current/Next values. Some Control Selectors are
'Dual-Ranked'. Software may either update the Current value directly
for immediate effect. Alternatively, software may write into the
'Next' values and update the SoundWire 1.2 'Commit Groups' register
to copy 'Next' values into 'Current' ones in a synchronized
manner. This is different from bank switching which is typically
used to change the bus configuration only.
- MBQ. the Multi-Byte Quantity bit is used to provide atomic updates
when accessing more that one byte, for example a 16-bit volume
control would be updated consistently, the intermediate values
mixing old MSB with new LSB are not applied.
These 6 parameters are used to build a 32-bit address to access the
desired Controls. Because of address range, paging is required, but
the most often used parameter values are placed in the lower 16 bits
of the address. This helps to keep the paging registers constant while
updating Controls for a specific Device/Function.
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201103172226.4278-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SoundWire 1.2 specification defines an "SDCA cascade" bit which
handles a logical OR of all SDCA interrupt sources (up to 30 defined).
Due to limitations of the addressing space, this bit is located in the
SDW_DP0_INT register when DP0 is used, or alternatively in the
DP0_SDCA_Support_INTSTAT register when DP0 is not used.
To allow for both cases to be handled, this bit will be checked in the
main device-level interrupt handling code. This will result in the
register being read twice if DP0 is enabled, but it's not clear how to
optimize this case. It's also more logical to deal with this interrupt
at the device than the port level, this bit is really not DP0 specific
and its location in the DP0_INTSTAT bit is only due to the lack of
free space in SCP_INTSTAT_1.
The SDCA_Cascade bit cannot be masked or cleared, so the interrupt
handling only forwards the detection to the Slave driver, which will
deal with reading the relevant SDCA status bits and clearing them. The
bus driver only signals the detection.
The communication with the Slave driver is based on the same interrupt
callback, with only an extension to provide the status of the
sdca_cascade bit.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201104152358.9518-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This algorithm computes bus parameters like clock frequency, frame
shape and port transport parameters based on active stream(s) running
on the bus.
Developers can also implement their own .compute_params() callback for
specific resource management algorithm, and set if before calling
sdw_add_bus_master()
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah. All hard-coded
values were removed from the initial contribution to use BIOS
information instead.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200908131520.5712-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Hardware-based synchronization is typically required when the
bus->multi_link flag is set.
On Intel platforms, when the Cadence IP is configured in 'Multi Master
Mode', the hardware synchronization is required even when a stream
only uses a single segment. The existing code only deal with hardware
synchronization when a stream uses more than one segment so to remain
backwards compatible we add a configuration threshold. For Intel cases
this threshold will be set to one, other platforms may be able to use
the SSP-based sync in those cases.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code allocates memory for the total number of ports.
This only works if the ports are contiguous, but will break if e.g. a
Devices uses port0, 1, and 14. The port_ready[] array would contain 3
elements, which would lead to an out-of-bounds access. Conversely in
other cases, the wrong port index would be used leading to timeouts on
prepare.
This can be fixed by allocating for the worst-case of 15
ports (DP0..DP14). In addition since the number is now fixed, we can
use an array instead of a dynamic allocation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200831134318.11443-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Somehow the existing code is not aligned with the steps described in
the documentation, refactor code and make sure the register
programming sequences are correct. Also add missing power-up,
power-down and wake capabilities (the last two are used in follow-up
patches but introduced here for consistency).
Some of the SHIM registers exposed fields that are link specific, and
in addition some of the power-related registers (SPA/CPA) take time to
be updated. Uncontrolled access leads to timeouts or errors. Add a
mutex, shared by all links, so that all accesses to such registers are
serialized, and follow a pattern of read-modify-write.
This includes making sure SHIM_SYNC is programmed only once, before
the first master is powered on. We use a 'shim_mask' field, shared
between all links and protected by a mutex, to deal with power-up and
power-down sequences.
Note that the SYNCPRD value is tied only to the XTAL value and not the
current bus frequency or the frame rate.
BugLink: https://github.com/thesofproject/linux/issues/1555
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
