Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26 ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2 ("usb: hub: Fix usb enumeration issue due to address0
race")
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Putting USB gadgets on a new bus of their own encounters a problem
when multiple gadgets are present: They all have the same name! The
driver core fails with a "sys: cannot create duplicate filename" error
when creating any of the /sys/bus/gadget/devices/<gadget-name>
symbolic links after the first.
This patch fixes the problem by adding a ".N" suffix to each gadget's
name when the gadget is registered (where N is a unique ID number),
thus making the names distinct.
Reported-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Link: https://lore.kernel.org/r/YnqKAXKyp9Vq/pbn@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub, support for other configurations could be added if
needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220217104219.v21.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a "gadget" bus and uses it for registering gadgets and
their drivers. From now on, bindings will be managed by the driver
core rather than through ad-hoc manipulations in the UDC core.
As part of this change, the driver_pending_list is removed. The UDC
core won't need to keep track of unbound drivers for later binding,
because the driver core handles all of that for us.
However, we do need one new feature: a way to prevent gadget drivers
from being bound to more than one gadget at a time. The existing code
does this automatically, but the driver core doesn't -- it's perfectly
happy to bind a single driver to all the matching devices on the bus.
The patch adds a new bitflag to the usb_gadget_driver structure for
this purpose.
A nice side effect of this change is a reduction in the total lines of
code, since now the driver core will do part of the work that the UDC
used to do.
A possible future patch could add udc devices to the gadget bus, say
as a separate device type.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSpdxaDNeC2BBOf@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding a "gadget" bus, this patch renames
usb_gadget_probe_driver() to usb_gadget_register_driver(). The new
name will be more accurate, since gadget drivers will be registered on
the gadget bus and the probing will be done by the driver core, not
the UDC core.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSc29YZvxgT5fEJ@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain ZTE modems, namely: MF823. MF831, MF910, built-in modem from
MF286R, expose both CDC-ECM and RNDIS network interfaces.
They have a trait of ignoring the locally-administered MAC address
configured on the interface both in CDC-ECM and RNDIS part,
and this leads to dropping of incoming traffic by the host.
However, the workaround was only present in CDC-ECM, and MF286R
explicitly requires it in RNDIS mode.
Re-use the workaround in rndis_host as well, to fix operation of MF286R
module, some versions of which expose only the RNDIS interface. Do so by
introducing new flag, RNDIS_DRIVER_DATA_DST_MAC_FIXUP, and testing for it
in rndis_rx_fixup. This is required, as RNDIS uses frame batching, and all
of the packets inside the batch need the fixup. This might introduce a
performance penalty, because test is done for every returned Ethernet
frame.
Apply the workaround to both "flavors" of RNDIS interfaces, as older ZTE
modems, like MF823 found in the wild, report the USB_CLASS_COMM class
interfaces, while MF286R reports USB_CLASS_WIRELESS_CONTROLLER.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduces a workaround for certain ZTE modems reporting invalid MAC
addresses over CDC-ECM.
The same issue was present on their RNDIS interface,which was fixed in
commit a5a18bdf74 ("rndis_host: Set valid random MAC on buggy devices").
However, internal modem of ZTE MF286R router, on its RNDIS interface, also
exhibits a second issue fixed already in CDC-ECM, of the device not
respecting configured random MAC address. In order to share the fixup for
this with rndis_host driver, export the workaround function, which will
be re-used in the following commit in rndis_host.
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Basic programmable non-PD Type-C port controllers do not need the full
TCPM library, but they share the same devicetree binding and the same
typec_capability structure. Factor out a helper for parsing those
properties which map to fields in struct typec_capability, so the code
can be shared between TCPM and basic non-TCPM drivers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220214050118.61015-4-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The <linux/usb/ch9.h> header is used over 1,400 times in a typical distro
build, but few of its users actually need the full <linux/device.h> header.
--------------------------------------------------------------------
| Combined, preprocessed C code size of header, without line markers,
| with comments stripped:
-------------------------
before: | #include <linux/usb/ch9.h> | LOC: 7,078 | headers: 172
after: | #include <linux/usb/ch9.h> | LOC: 812 | headers: 38
Remove it and add it to the places that need it.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of trying to keep track of the connections to the
USB Type-C connectors separately, letting the component
framework take care of that.
From now on every USB Type-C connector will register itself
as "aggregate" - component master - and anything that can be
connected to it inside the system can then simply register
itself as a generic component.
The matching of the components and the connector shall rely
on ACPI _PLD initially. Before registering itself as the
aggregate, the connector will find all other ACPI devices
that have matching _PLD crc hash with it (matching value in
the pld_crc member of struct acpi_device), and add a
component match entry for each one of them. Because only
ACPI is supported for now, the driver shall only be build
when ACPI is supported.
This removes the need for the custom API that the driver
exposed. The components and the connector can therefore
exist completely independently of each other. The order in
which they are registered, as well as are they modules or
not, is now irrelevant.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20211223082422.45637-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor struct ehci_regs to avoid accessing beyond the end of
port_status. This change results in no difference in the final
object code.
Avoids several warnings when building with -Warray-bounds:
drivers/usb/host/ehci-brcm.c: In function 'ehci_brcm_reset':
drivers/usb/host/ehci-brcm.c:113:32: warning: array subscript 16 is above array bounds of 'u32[15]' {aka 'unsigned int[15]'} [-Warray-bounds]
113 | ehci_writel(ehci, 0x00800040, &ehci->regs->port_status[0x10]);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/ehci.h:274,
from drivers/usb/host/ehci-brcm.c:15:
./include/linux/usb/ehci_def.h:132:7: note: while referencing 'port_status'
132 | u32 port_status[HCS_N_PORTS_MAX];
| ^~~~~~~~~~~
Note that the documentation around this proprietary register was
confusing. If "USB_EHCI_INSNREG00" is at port_status[0x0f], its offset
would be 0x80 (not 0x90). The comments have been adjusted to fix this
apparent typo.
Fixes: 9df231511b ("usb: ehci: Add new EHCI driver for Broadcom STB SoC's")
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818173018.2259231-3-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
