v3: s-o-b comment, explanation of performance and descision for
the start/stop implementation
Implementing rmw functionality for RAID6 requires optimized syndrome
calculation. Up to now we can only generate a complete syndrome. The
target P/Q pages are always overwritten. With this patch we provide
a framework for inplace P/Q modification. In the first place simply
fill those functions with NULL values.
xor_syndrome() has two additional parameters: start & stop. These
will indicate the first and last page that are changing during a
rmw run. That makes it possible to avoid several unneccessary loops
and speed up calculation. The caller needs to implement the following
logic to make the functions work.
1) xor_syndrome(disks, start, stop, ...): "Remove" all data of source
blocks inside P/Q between (and including) start and end.
2) modify any block with start <= block <= stop
3) xor_syndrome(disks, start, stop, ...): "Reinsert" all data of
source blocks into P/Q between (and including) start and end.
Pages between start and stop that won't be changed should be filled
with a pointer to the kernel zero page. The reasons for not taking NULL
pages are:
1) Algorithms cross the whole source data line by line. Thus avoid
additional branches.
2) Having a NULL page avoids calculating the XOR P parity but still
need calulation steps for the Q parity. Depending on the algorithm
unrolling that might be only a difference of 2 instructions per loop.
The benchmark numbers of the gen_syndrome() functions are displayed in
the kernel log. Do the same for the xor_syndrome() functions. This
will help to analyze performance problems and give an rough estimate
how well the algorithm works. The choice of the fastest algorithm will
still depend on the gen_syndrome() performance.
With the start/stop page implementation the speed can vary a lot in real
life. E.g. a change of page 0 & page 15 on a stripe will be harder to
compute than the case where page 0 & page 1 are XOR candidates. To be not
to enthusiatic about the expected speeds we will run a worse case test
that simulates a change on the upper half of the stripe. So we do:
1) calculation of P/Q for the upper pages
2) continuation of Q for the lower (empty) pages
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull md update from Neil Brown:
"Headline item is multithreading for RAID5 so that more IO/sec can be
supported on fast (SSD) devices. Also TILE-Gx SIMD suppor for RAID6
calculations and an assortment of bug fixes"
* tag 'md/3.12' of git://neil.brown.name/md:
raid5: only wakeup necessary threads
md/raid5: flush out all pending requests before proceeding with reshape.
md/raid5: use seqcount to protect access to shape in make_request.
raid5: sysfs entry to control worker thread number
raid5: offload stripe handle to workqueue
raid5: fix stripe release order
raid5: make release_stripe lockless
md: avoid deadlock when dirty buffers during md_stop.
md: Don't test all of mddev->flags at once.
md: Fix apparent cut-and-paste error in super_90_validate
raid6/test: replace echo -e with printf
RAID: add tilegx SIMD implementation of raid6
md: fix safe_mode buglet.
md: don't call md_allow_write in get_bitmap_file.
This change adds TILE-Gx SIMD instructions to the software raid
(md), modeling the Altivec implementation. This is only for Syndrome
generation; there is more that could be done to improve recovery,
as in the recent Intel SSE3 recovery implementation.
The code unrolls 8 times; this turns out to be the best on tilegx
hardware among the set 1, 2, 4, 8 or 16. The code reads one
cache-line of data from each disk, stores P and Q then goes to the
next cache-line.
The test code in sys/linux/lib/raid6/test reports 2008 MB/s data
read rate for syndrome generation using 18 disks (16 data and 2
parity). It was 1512 MB/s before this SIMD optimizations. This is
running on 1 core with all the data in cache.
This is based on the paper The Mathematics of RAID-6.
(http://kernel.org/pub/linux/kernel/people/hpa/raid6.pdf).
Signed-off-by: Ken Steele <ken@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Rebased/reworked a patch contributed by Rob Herring that uses
NEON intrinsics to perform the RAID-6 syndrome calculations.
It uses the existing unroll.awk code to generate several
unrolled versions of which the best performing one is selected
at boot time.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: hpa@linux.intel.com
Empty files can get deleted by the patch program, so remove empty Kbuild
files and their links from the parent Kbuilds.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Optimize RAID6 recovery functions to take advantage of
the 256-bit YMM integer instructions introduced in AVX2.
The patch was tested and benchmarked before submission.
However hardware is not yet released so benchmark numbers
cannot be reported.
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add SSSE3 optimized recovery functions, as well as a system
for selecting the most appropriate recovery functions to use.
Originally-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When reshaping we can avoid costly intermediate backup by
changing the 'start' address of the array on the device
(if there is enough room).
So as a first step, allow such a change to be requested
through sysfs, and recorded in v1.x metadata.
(As we didn't previous check that all 'pad' fields were zero,
we need a new FEATURE flag for this.
A (belatedly) check that all remaining 'pad' fields are
zero to avoid a repeat of this)
The new data offset must be requested separately for each device.
This allows each to have a different change in the data offset.
This is not likely to be used often but as data_offset can be
set per-device, new_data_offset should be too.
This patch also removes the 'acknowledged' arg to rdev_set_badblocks as
it is never used and never will be. At the same time we add a new
arg ('in_new') which is currently always zero but will be used more
soon.
When a reshape finishes we will need to update the data_offset
and rdev->sectors. So provide an exported function to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently a reshape operation always progresses from the start
of the array to the end unless the number of devices is being
reduced, in which case it progressed in the opposite direction.
To reverse a partial reshape which changes the number of devices
you can stop the array and re-assemble with the raid-disks numbers
reversed and it will undo.
However for a reshape that does not change the number of devices
it is not possible to reverse the reshape in the middle - you have to
wait until it completes.
So add a 'reshape_direction' attribute with is either 'forwards' or
'backwards' and can be explicitly set when delta_disks is zero.
This will become more important when we allow the data_offset to
change in a reshape. Then the explicit statement of what direction is
being used will be more useful.
This can be enabled in raid5 trivially as it already supports
reverse reshape and just needs to use a different trigger to request it.
Signed-off-by: NeilBrown <neilb@suse.de>
hot-replace is a feature being added to md which will allow a
device to be replaced without removing it from the array first.
With hot-replace a spare can be activated and recovery can start while
the original device is still in place, thus allowing a transition from
an unreliable device to a reliable device without leaving the array
degraded during the transition. It can also be use when the original
device is still reliable but it not wanted for some reason.
This will eventually be supported in RAID4/5/6 and RAID10.
This patch adds a super-block flag to distinguish the replacement
device. If an old kernel sees this flag it will reject the device.
It also adds two per-device flags which are viewable and settable via
sysfs.
"want_replacement" can be set to request that a device be replaced.
"replacement" is set to show that this device is replacing another
device.
The "rd%d" links in /sys/block/mdXx/md only apply to the original
device, not the replacement. We currently don't make links for the
replacement - there doesn't seem to be a need.
Signed-off-by: NeilBrown <neilb@suse.de>
While using etags to find free_pages(), I stumbled across this debug
definition of free_pages() that is to be used while debugging some raid
code in userspace. The __get_free_pages() allocates the correct size,
but the free_pages() does not match. free_pages(), like
__get_free_pages(), takes an order and not a size.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Space must have been allocated when array was created.
A feature flag is set when the badblock list is non-empty, to
ensure old kernels don't load and trust the whole device.
We only update the on-disk badblocklist when it has changed.
If the badblocklist (or other metadata) is stored on a bad block, we
don't cope very well.
If metadata has no room for bad block, flag bad-blocks as disabled,
and do the same for 0.90 metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ Raid5 has learned to take over also raid4 and raid6 arrays.
2/ new_chunk in mdp_superblock_1 is in sectors, not bytes.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the raid6 data processing routines into a standalone module
(raid6_pq) to prepare them to be called from async_tx wrappers and other
non-md drivers/modules. This precludes a circular dependency of raid456
needing the async modules for data processing while those modules in
turn depend on raid456 for the base level synchronous raid6 routines.
To support this move:
1/ The exportable definitions in raid6.h move to include/linux/raid/pq.h
2/ The raid6_call, recovery calls, and table symbols are exported
3/ Extra #ifdef __KERNEL__ statements to enable the userspace raid6test to
compile
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h
Remove include/raid/md.h as its only remaining use was to #include
other files.
Signed-off-by: NeilBrown <neilb@suse.de>
The extern function definitions are kernel-internal definitions, so
they belong in md_k.h
The MD_*_VERSION values could reasonably go in a number of places,
but md_u.h seems most reasonable.
This leaves almost nothing in md.h. It will go soon.
Signed-off-by: NeilBrown <neilb@suse.de>
.. as they are part of the user-space interface.
Also move MdpMinorShift into there so we can remove duplication.
Lastly move mdp_major in. It is less obviously part of the user-space
interface, but do_mounts_md.c uses it, and it is acting a bit like
user-space.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away. md.h is left where it is for now as there
are some uses from the outside.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
