AT91 slow clk is a clk multiplexer.
In some SoCs (sam9x5, sama5, sam9g45 families) this multiplexer can
choose among 2 sources: an internal RC oscillator circuit and an oscillator
using an external crystal.
In other Socs (sam9260 family) the multiplexer source is hardcoded with
the OSCSEL signal.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull ARM SoC late cleanups from Arnd Bergmann:
"These could not be part of the first cleanup branch, because they
either came too late in the cycle, or they have dependencies on other
branches. Important changes are:
- The integrator platform is almost multiplatform capable after some
reorganization (Linus Walleij)
- Minor cleanups on Zynq (Michal Simek)
- Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks
bindings are rearranged"
* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
devicetree: fix newly added exynos sata bindings
ARM: EXYNOS: Fix compilation error in cpuidle.c
ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
ARM: EXYNOS: Remove hardware.h file
ARM: SAMSUNG: Remove hardware.h inclusion
ARM: S3C24XX: Remove invalid code from hardware.h
dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
ARM: dts: Keep some essential LDOs enabled for arndale-octa board
ARM: dts: Disable MDMA1 node for arndale-octa board
ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
serial: s3c: Fix build of header without serial_core.h preinclusion
ARM: EXYNOS: Allow wake-up using GIC interrupts
ARM: EXYNOS: Stop using legacy Samsung PM code
ARM: EXYNOS: Remove PM initcalls and useless indirection
ARM: EXYNOS: Fix abuse of CONFIG_PM
ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
ARM: SAMSUNG: Move common save/restore helpers to separate file
ARM: SAMSUNG: Move Samsung PM debug code into separate file
ARM: SAMSUNG: Consolidate PM debug functions
ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
...
If CLK_SET_RATE_PARENT is set for a clkoutx2 clock, calling
clk_set_rate() on the clock "skips" the x2 multiplier as there are no
set_rate and round_rate functions defined for the clkoutx2.
This results in getting double the requested clock rates, breaking the
display on omap3430 based devices. This got broken when
d0f58bd3bb and related patches were merged
for v3.14, as omapdss driver now relies more on the clk-framework and
CLK_SET_RATE_PARENT.
This patch implements set_rate and round_rate for clkoutx2.
Tested on OMAP3430, OMAP3630, OMAP4460.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clkc has its registers in the range of the slcr.
Instead of passing around the slcr base address pointer, let the clkc get the
address from the DT.
This prepares the slcr to be a real driver with multiple memory ranges
(slcr, clocks, pinctrl,...)
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pull more clock framework changes from Mike Turquette:
"The second half of the clock framework pull requeust for 3.14 is
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for
Samsung chips.
Additionally there are other smaller clock driver changes and several
last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request"
[ Fix up stupid compile error in the source tree with evil merge - Grumpy Linus ]
* tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux: (49 commits)
clk: sort Makefile
clk: sunxi: fix overflow when setting up divided factors
clk: Export more clk-provider functions
dt-bindings: qcom: Fix warning with duplicate dt define
clk: si5351: remove variant from platform_data
clk: samsung: Remove unneeded semicolon
clk: qcom: Fix modular build
ARM: OMAP3: use DT clock init if DT data is available
ARM: AM33xx: remove old clock data and link in new clock init code
ARM: AM43xx: Enable clock init
ARM: OMAP: DRA7: Enable clock init
ARM: OMAP4: remove old clock data and link in new clock init code
ARM: OMAP2+: io: use new clock init API
ARM: OMAP2+: PRM: add support for initializing PRCM clock modules from DT
ARM: OMAP3: hwmod: initialize clkdm from clkdm_name
ARM: OMAP: hwmod: fix an incorrect clk type cast with _get_clkdm
ARM: OMAP2+: clock: use driver API instead of direct memory read/write
ARM: OMAP2+: clock: add support for indexed memmaps
ARM: dts: am43xx clock data
ARM: dts: AM35xx: use DT clock data
...
clk-43xx.c now contains the clock init functionality for am43xx, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-3xxx.c now contains the clock init functionality for omap3, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
OMAP3 has interface clocks in addition to functional clocks, which
require special handling for the autoidle and idle status register
offsets mainly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-33xx.c now contains the clock init functionality for am33xx, including
DT clock registration and adding of static clkdev entries.
This patch also moves the omap2_clk_enable_init_clocks declaration to
the driver include, as this is needed by the am33xx clock init code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-7xx.c now contains the clock init functionality for dra7, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-54xx.c now contains the clock init functionality for omap5, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-44xx.c now contains the clock init functionality for omap4, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
ti,mux-clock provides now a binding for basic mux support. This is just
using the basic clock type.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some OMAP clocks require knowledge about their parent clockdomain for
book keeping purposes. This patch creates a new DT binding for TI
clockdomains, which act as a collection of device clocks. Clockdomain
itself is rather misleading name for the hardware functionality, as at
least on OMAP4 / OMAP5 / DRA7 the clockdomains can be collections of either
clocks and/or IP blocks, thus idle-domain or such might be more appropriate.
For most cases on these SoCs, the kernel doesn't even need the information
and the mappings can be ignored.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for TI specific gate clocks. These behave as basic
gate-clock, but have different ops / hw-ops for controlling the actual
gate, for example waiting until the clock is ready. Several sub-types
are supported:
- ti,gate-clock: basic gate clock with default ops/hwops
- ti,clkdm-gate-clock: clockdomain level gate control
- ti,dss-gate-clock: gate clock with DSS specific hardware handling
- ti,am35xx-gate-clock: gate clock with AM35xx specific hardware handling
- ti,hsdiv-gate-clock: gate clock with OMAP36xx hardware errata handling
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for TI divider clock binding, which simply uses
the basic clock divider to provide the features needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a multipurpose clock node, which contains support for multiple
sub-clocks. Uses basic composite clock type to implement the actual
functionality, and TI specific gate, mux and divider clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
TI clk driver now routes some of the basic clocks through own
registration routine to allow autoidle support. This routine just
checks a couple of device node properties and adds autoidle support
if required, and just passes the registration forward to basic clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The OMAP clock driver now supports DPLL clock type. This patch also
adds support for DT DPLL nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
ti_dt_clk_init_provider() can now be used to initialize the contents of
a single clock IP block. This parses all the clocks under the IP block
and calls the corresponding init function for them.
This patch also introduces a helper function for the TI clock drivers
to get register info from DT and append the master IP info to this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some devices require their clocks to be available with a specific
dev-id con-id mapping. With DT, the clocks can be found by default
only with their name, or alternatively through the device node of
the consumer. With drivers, that don't support DT fully yet, add
mechanism to register specific clock names.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:
- Fixed rate clocks with multiplier and divisor set according to boot
mode configuration
- Custom divider clocks with SoC-specific divider values
This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Now that no code uses the custom Tegra module reset API, we can remove
its implementation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
