This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.
The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In addition to vendor-specific commands, also support vendor-specific
events. These must be registered with cfg80211 before they can be used.
They're also advertised in nl80211 in the wiphy information so that
userspace knows can be expected. The events themselves are sent on a
new multicast group called "vendor".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT MCS/NSS set support for nl80211_set_tx_bitrate_mask().
This should be used mainly for test purpose, to check
different MCS/NSS VHT combinations.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also
rename mcs to ht_mcs in struct cfg80211_bitrate_mask.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for vendor-specific commands to nl80211. This is
intended to be used for really vendor-specific functionality
that can't be implemented in a generic fashion for any reason.
It's *NOT* intended to be used for any normal/generic feature
or any optimisations that could be implemented across drivers.
Currently, only vendor commands (with replies) are supported,
no dump operations or vendor-specific notifications.
Also add a function wdev_to_ieee80211_vif() to mac80211 which
is needed for mac80211-based drivers wanting to implement any
vendor commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This attribute is needed for setting Operating Mode Notification
in AP mode from User Space. This functionality is required when
User Space received Assoc Request contains Operation Mode
Notification element.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
[fix typos, nl80211 documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nla_put_flag needs a real nl80211 attribute id, not a wiphy flag bit.
While at it, split 5 and 10 MHz capability flags in case we ever need
to support hardware that can only do one of the two.
Also move the flag settings to the split-only information so we don't
increase the space needed for old userspace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[change location of flag setting]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This command has different semantics depending on the action code sent.
Document this fact and detail the supported action codes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To use DFS in IBSS mode, userspace is required to react to radar events.
It can inform nl80211 that it is capable of doing so by adding a
NL80211_ATTR_HANDLE_DFS attribute when joining the IBSS.
This attribute is supplied to let the kernelspace know that the
userspace application can and will handle radar events, e.g. by
intiating channel switches to a valid channel. DFS channels may
only be used if this attribute is supplied and the driver supports
it. Driver support will be checked even if a channel without DFS
will be initially joined, as a DFS channel may be chosen later.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix attribute name in commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's supported channels and supported operating
classes are required for the driver to perform TDLS off channel
operations. This commit enhances the function nl80211_(new)set_station
to pass this information of the peer to the driver.
Signed-off-by: Sunil Dutt <c_duttus@qti.qualcomm.com>
[return errors for malformed tuples]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is incorrect to refer to this as 11d as 802.11d was just a
proposed amendment, 802.11d was merged to the standard so
use proper terminology.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The names are prefixed incorrectly on the documentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[also remove spurious blank line]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow channel switch announcements within beacons, add
the channel switch command to nl80211/cfg80211. This is
implementation is intended for AP and (later) IBSS mode.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In most cases, host that receives IPv4 and IPv6 multicast/broadcast
packets does not do anything with these packets. Therefore the
reception of these unwanted packets causes unnecessary processing
and power consumption.
Packet coalesce feature helps to reduce number of received
interrupts to host by buffering these packets in firmware/hardware
for some predefined time. Received interrupt will be generated when
one of the following events occur.
a) Expiration of hardware timer whose expiration time is set to
maximum coalescing delay of matching coalesce rule.
b) Coalescing buffer in hardware reaches it's limit.
c) Packet doesn't match any of the configured coalesce rules.
This patch adds set/get configuration support for packet coalesce.
User needs to configure following parameters for creating a coalesce
rule.
a) Maximum coalescing delay
b) List of packet patterns which needs to be matched
c) Condition for coalescence. pattern 'match' or 'no match'
Multiple such rules can be created.
This feature needs to be advertised during driver initialization.
Drivers are supposed to do required firmware/hardware settings based
on user configuration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[fix kernel-doc, change free function, fix copy/paste error]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Currently packet patterns and it's enum/structures are used only
for WoWLAN feature. As we intend to reuse them for new feature
packet coalesce, they are renamed in this patch.
Older names are kept for backward compatibility purpose.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Add defines for 5 and 10 MHz channel width and fix channel
handling functions accordingly.
Also check for and report the WIPHY_FLAG_SUPPORTS_5_10_MHZ
capability.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix spelling in comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.
In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication takes place in userspace, but the beacon is
generated in the kernel. Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support auto-loading of wireless modules from netlink users, add module
alias for nl80211 family.
This also adds NL80211_GENL_NAME constant to define the "nl80211" netlink
family name as part of uapi.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
