The transfer_one_message callback handles messages, not transfers.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Explicitly note the transfer_one and transfer_one_message are mutually
exclusive, to make the text a little more newcomers friendly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull spi updates from Mark Brown:
"A respun version of the merges for the pull request previously sent
with a few additional fixes. The last two merges were fixed up by
hand since the branches have moved on and currently have the prior
merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller
- Fix duplicate device registration for ACPI
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends)
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers"
* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
spi: core: Fix transfer failure when master->transfer_one returns positive value
spi: Correct set_cs() documentation
spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
spi: Spelling s/finised/finished/
spi: sc18is602: Convert to use bits_per_word_mask
spi: Remove duplicate code to set default bits_per_word setting
spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
spi: clps711x: Add MODULE_ALIAS to support module auto-loading
spi: rspi: Add missing clk_disable() calls in error and cleanup paths
spi: rspi: Spelling s/transmition/transmission/
spi: rspi: Add support for specifying CPHA/CPOL
spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
spi: rspi: Add more QSPI register documentation
spi: rspi: Add more RSPI register documentation
spi: rspi: Remove dependency on DMAE for SHMOBILE
spi/s3c64xx: Correct indentation
spi: sh: Use spi_sh_clear_bit() instead of open-coded
spi: bitbang: Grammar s/make to make/to make/
spi: sh-hspi: Spelling s/recive/receive/
spi: core: Improve tx/rx_nbits check comments
...
The documentation for spi_master.set_cs() says:
assert or deassert chip select, true to assert
i.e. its "enable" parameter uses assertion-level logic.
This does not match the implementation of spi_set_cs(), which calls
spi_master.set_cs() with the wanted logic level of the chip select line,
which depends on the polarity of the chip select signal.
Correct the documentation to match the implementation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi_write_then_read() takes a "void *" for rxbuf, so there's no need to
cast the buffer pointer to "u8 *".
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Trent Piepho observed that since the current realistic maximum number of
data lines is four we can pack the spi_transfer struct more efficiently
if we use a bitfield for the number of bits, allowing the fields to fit
in a single byte along with cs_change.
If space becomes an issue further optimiation is possible by only using
the constants and packing the values chosen for them.
Reported-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fiq.h contains only a function declaration and is not used by anyone
else. Move the declaration to the driver header file and remove the
unnecessary platform dependency from the driver.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that spi_device->mode is a u16, the chip_select, bits_per_mode,
and mode fields pack poorly, taking 8 bytes: four data and four
padding. By moving (u8)bits_per_word up one position, to after
(u8)chip_select, they pack better and only use 4 bytes.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>g
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 20bc4d5d56
(gpio: 74x164: Add support for the daisy-chaining) introduce check
for DT for the driver, so driver cannot be used without DT.
There are no in-tree users of this driver, so remove non-DT support
completely.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The loops which SPI controller drivers use to process the list of transfers
in a spi_message are typically very similar and have some error prone areas
such as the handling of /CS. Help simplify drivers by factoring this code
out into the core - if drivers provide a transfer_one() function instead
of a transfer_one_message() function the core will handle processing at the
message level.
/CS can be controlled by either setting cs_gpio or providing a set_cs
function. If this is not possible for hardware reasons then both can be
omitted and the driver should continue to implement manual /CS handling.
This is a first step in refactoring and it is expected that there will be
further enhancements, for example factoring out of the mapping of transfers
for DMA and the initiation and completion of interrupt driven transfers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Many SPI drivers perform setup and tear down on every message, usually
doing things like DMA mapping the message. Provide hooks for them to use
to provide such operations.
This is of limited value for drivers that implement transfer_one_message()
but will be of much greater utility with future factoring out of standard
implementations of that function.
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a new spi_w8r16be() helper, which is similar to spi_w8r16()
except that it converts the read data word from big endian to native endianness
before returning it. The reason for introducing this new helper is that for SPI
slave devices it is quite common that the read 16 bit data word is in big
endian. So users of spi_w8r16() have to convert the result to native endianness
manually. A second reason is that in this case the endianness of the return
value of spi_w8r16() depends on its sign. If it is negative (i.e. a error code)
it is already in native endianness, if it is positive it is in big endian. The
sparse code checker doesn't like this kind of mixed endianness and special
annotations are necessary to keep it quiet (E.g. casting to be16 using __force).
Doing the conversion to native endianness in the helper function does not
require such annotations since we are not mixing different endiannesses in the
same variable.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Help simplify the cleanup code for SPI master drivers by providing a
managed master registration function, ensuring that the master is
automatically unregistered whenever the device is unbound.
Signed-off-by: Mark Brown <broonie@linaro.org>
The R8A7790 has QSPI module which is very similar to RSPI.
This patch adds into RSPI module together to supports QSPI module.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
