[ Upstream commit f4f4276f985a5aac7b310a4ed040b47e275e7591 ]
Some PMICs treat the vsel_reg same as apply-bit. Eg, when voltage range
is changed, the new voltage setting is not taking effect until the vsel
register is written.
Add a flag 'range_applied_by_vsel' to the regulator desc to indicate this
behaviour and to force the vsel value to be written to hardware if range
was changed, even if the old selector was same as the new one.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://msgid.link/r/ZktCpcGZdgHWuN_L@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 1ace99d7c7c4 ("regulator: tps6287x: Force writing VSEL bit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff33132605c1a0acea59e4c523cb7c6fabe856b2 ]
The devm_regulator_get_enable_optional() should be a 'call and forget'
API, meaning, when it is used to enable the regulators, the API does not
provide a handle to do any further control of the regulators. It gives
no real benefit to return an error from the stub if CONFIG_REGULATOR is
not set.
On the contrary, returning an error is causing problems to drivers when
hardware is such it works out just fine with no regulator control.
Returning an error forces drivers to specifically handle the case where
CONFIG_REGULATOR is not set, making the mere existence of the stub
questionalble.
Change the stub implementation for the
devm_regulator_get_enable_optional() to return Ok so drivers do not
separately handle the case where the CONFIG_REGULATOR is not set.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: da279e6965 ("regulator: Add devm helpers for get and enable")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/ZiedtOE00Zozd3XO@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96e20adc43c4f81e9163a5188cee75a6dd393e09 ]
The devm_regulator_get_enable() should be a 'call and forget' API,
meaning, when it is used to enable the regulators, the API does not
provide a handle to do any further control of the regulators. It gives
no real benefit to return an error from the stub if CONFIG_REGULATOR is
not set.
On the contrary, returning and error is causing problems to drivers when
hardware is such it works out just fine with no regulator control.
Returning an error forces drivers to specifically handle the case where
CONFIG_REGULATOR is not set, making the mere existence of the stub
questionalble. Furthermore, the stub of the regulator_enable() seems to
be returning Ok.
Change the stub implementation for the devm_regulator_get_enable() to
return Ok so drivers do not separately handle the case where the
CONFIG_REGULATOR is not set.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reported-by: Aleksander Mazur <deweloper@wp.pl>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: da279e6965 ("regulator: Add devm helpers for get and enable")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/ZiYF6d1V1vSPcsJS@drtxq0yyyyyyyyyyyyyby-3.rev.dnainternet.fi
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Right now the regulator helpers expect raw register values for the range
selectors. This is different from the voltage selectors, which are
normalized as bitfield values. This leads to a bit of confusion. Also,
raw values are harder to copy from datasheets or match up with them,
as datasheets will typically have bitfield values.
Make the helpers expect bitfield values, and convert existing users. The
field in regulator_desc is renamed to |linear_range_selectors_bitfield|.
This is intended to cause drivers added in the same merge window and
out-of-tree drivers using the incorrect variable and values to break,
preventing incorrect values being used on actual hardware and potentially
producing magic smoke.
Also include bitops.h explicitly for ffs(), and reorder the header include
statements. While at it, also replace module.h with export.h, since the
only use is EXPORT_SYMBOL_GPL.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230714081408.274567-1-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull regulator updates from Mark Brown:
"This release is almost all drivers, there's some small improvements in
the core but otherwise everything is updates to drivers, mostly the
addition of new ones.
There's also a bunch of changes pulled in from the MFD subsystem as
dependencies, Rockchip and TI core MFD code that the regulator drivers
depend on.
I've also yet again managed to put a SPI commit in the regulator tree,
I don't know what it is about those two trees (this for
spi-geni-qcom).
Summary:
- Support for Renesas RAA215300, Rockchip RK808, Texas Instruments
TPS6594 and TPS6287x, and X-Powers AXP15060 and AXP313a"
* tag 'regulator-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (43 commits)
regulator: Add Renesas PMIC RAA215300 driver
regulator: dt-bindings: Add Renesas RAA215300 PMIC bindings
regulator: ltc3676: Use maple tree register cache
regulator: ltc3589: Use maple tree register cache
regulator: helper: Document ramp_delay parameter of regulator_set_ramp_delay_regmap()
regulator: mt6358: Use linear voltage helpers for single range regulators
regulator: mt6358: Const-ify mt6358_regulator_info data structures
regulator: mt6358: Drop *_SSHUB regulators
regulator: mt6358: Merge VCN33_* regulators
regulator: dt-bindings: mt6358: Drop *_sshub regulators
regulator: dt-bindings: mt6358: Merge ldo_vcn33_* regulators
regulator: dt-bindings: pwm-regulator: Add missing type for "pwm-dutycycle-unit"
regulator: Switch two more i2c drivers back to use .probe()
spi: spi-geni-qcom: Do not do DMA map/unmap inside driver, use framework instead
soc: qcom: geni-se: Add interfaces geni_se_tx_init_dma() and geni_se_rx_init_dma()
regulator: tps6594-regulator: Add driver for TI TPS6594 regulators
regulator: axp20x: Add AXP15060 support
regulator: axp20x: Add support for AXP313a variant
dt-bindings: pfuze100.yaml: Add an entry for interrupts
regulator: stm32-pwr: Fix regulator disabling
...
The *_SSHUB regulators are actually alternate configuration interfaces
for their non *_SSHUB counterparts. They are not separate regulator
outputs. These registers are intended for the companion processor to
use to configure the power rails while the main processor is sleeping.
They are not intended for the main operating system to use.
Since they are not real outputs they shouldn't be modeled separately.
Remove them. Luckily no device tree actually uses them.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230609083009.2822259-5-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The VCN33_BT and VCN33_WIFI regulators are actually the same regulator,
having the same voltage setting and output pin. There are simply two
enable bits that are ORed together to enable the regulator.
Having two regulators representing the same output pin is misleading
from a design matching standpoint, and also error-prone in driver
implementations. If consumers try to set different voltages on either
regulator, the one set later would override the one set before. There
are ways around this, such as chaining them together and having the
downstream one act as a switch. But given there's only one output pin,
such a workaround doesn't match reality.
Remove the VCN33_WIFI regulator. During the probe phase, have the driver
sync the enable status of VCN33_WIFI to VCN33_BT. Also drop the suffix
so that the regulator name matches the pin name in the datasheet.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230609083009.2822259-4-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Following by the below discussion, there's the potential UAF issue
between regulator and mfd.
https://lore.kernel.org/all/20221128143601.1698148-1-yangyingliang@huawei.com/
From the analysis of Yingliang
CPU A |CPU B
mt6370_probe() |
devm_mfd_add_devices() |
|mt6370_regulator_probe()
| regulator_register()
| //allocate init_data and add it to devres
| regulator_of_get_init_data()
i2c_unregister_device() |
device_del() |
devres_release_all() |
// init_data is freed |
release_nodes() |
| // using init_data causes UAF
| regulator_register()
It's common to use mfd core to create child device for the regulator.
In order to do the DT lookup for init data, the child that registered
the regulator would pass its parent as the parameter. And this causes
init data resource allocated to its parent, not itself. The issue happen
when parent device is going to release and regulator core is still doing
some operation of init data constraint for the regulator of child device.
To fix it, this patch expand 'regulator_register' API to use the
different devices for init data allocation and DT lookup.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1670311341-32664-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Corentin Labbe <clabbe@baylibre.com>:
This adds a new regulator_bulk_get_all() which grab all supplies
properties in a DT node, for use in implementing generic handling
for things like MDIO PHYs where the physical standardisation of
the bus does not extend to power supplies.
In addition to adding some fairly simple OF support code, we make some
slight adjustments to the userspace-consumer driver to properly
support use with regulator-output hardware:
- We now do an exclusive get of the supply regulators so as to
prevent regulator_init_complete_work from automatically disabling
them.
- Instead of assuming that the supply is initially disabled, we now
query its state to determine the initial value of drvdata->enabled.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20221031233704.22575-4-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
We had an exclusive variant of the devm_regulator_get() API, but no
corresponding variant for the bulk API; let's add one now. We add a
generalized version of the existing regulator_bulk_get() function that
additionally takes a get_type parameter and redefine
regulator_bulk_get() in terms of it, then do similarly with
devm_regulator_bulk_get(), and finally add the new
devm_regulator_bulk_get_exclusive().
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20221031233704.22575-2-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
This is simillar as fixed-regulator.
Used to extract regulator parent from the device tree.
Without that property used, the parent regulator can be shut down (if not an always on).
Thus leading to inappropriate behavior:
On am62-SP-SK this fix is required to avoid tps65219 ldo1 (SDMMC rail) to be shut down after boot completion.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Link: https://lore.kernel.org/r/20220929132526.29427-2-jneanne@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:
In an effort to give some love to the apparently forgotten MT6795 SoC,
I am upstreaming more components that are necessary to support platforms
powered by this one apart from a simple boot to serial console.
This series adds support for the regulators found in MT6331 and MT6332
main/companion PMICs.
Adding support to each driver in each subsystem is done in different
patch series as to avoid spamming uninteresting patches to maintainers.
Tested on a MT6795 Sony Xperia M5 (codename "Holly") smartphone.
Merge series from Douglas Anderson <dianders@chromium.org>:
The main goal of this series is to make a small dent in cleaning up
the way we deal with regulator loads. The idea is to add some extra
functionality to the regulator "bulk" API so that consumers can
specify the load using that.
Drivers tend to want to define the names of their regulators somewhere
in their source file as "static const". This means, inevitable, that
every driver out there open codes something like this:
static const char * const supply_names[] = {
"vcc", "vccl",
};
static int get_regulators(struct my_data *data)
{
int i;
data->supplies = devm_kzalloc(...)
if (!data->supplies)
return -ENOMEM;
for (i = 0; i < ARRAY_SIZE(supply_names); i++)
data->supplies[i].supply = supply_names[i];
return devm_regulator_bulk_get(data->dev,
ARRAY_SIZE(supply_names),
data->supplies);
}
Let's make this more convenient by doing providing a helper that does
the copy.
I have chosen to have the "const" input structure here be the exact
same structure as the normal one passed to
devm_regulator_bulk_get(). This is slightly inefficent since the input
data can't possibly have anything useful for "ret" or consumer and
thus we waste 8 bytes per structure. This seems an OK tradeoff for not
introducing an extra structure.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220726103631.v2.6.I38fc508a73135a5c1b873851f3553ff2a3a625f5@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a number of drivers that follow a pattern that looks like
this:
1. Use the regulator bulk API to get a bunch of regulators.
2. Set the load on each of the regulators to use whenever the
regulators are enabled.
Let's make this easier by just allowing the drivers to pass the load
in.
As part of this change we need to move the error printing in
regulator_bulk_get() around; let's switch to the new dev_err_probe()
to simplify it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220726103631.v2.4.Ie85f68215ada39f502a96dcb8a1f3ad977e3f68a@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
