As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch adds support for the PI7C9X442SL PCIe EHCI host controller
from Pericom.
Tested at P4080DS eval board from Freescale.
Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de>
Cc: Remy Bohmer <linux@bohmer.net>
The anomaly workarounds we need for older silicon might break things
if used on newer versions where the anomalies don't exist. So check
the silicon rev at runtime too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add waiting for receiving Ethernet gadget state on the Windows host
side before dropping pullup, but keep it for debug.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Port USB gadget RNDIS protocol support from linux-2.6.26
(.27 gadget stack actually has composite drivers).
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Disconnecting USB gadget with pending interrupt may cause its wrong
handling in the next time when interface will be started again
(especially actual for RNDIS). This interrupt may force the gadget
to queue unexpected response before setup stage.
Despite the fact that such interrupt handled after dropped pullup
also may add pending response, this will not bring to any issues due to
usb_ep_disable (which clears the queue) called on gadget unregistering.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.
The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Changed both to use a common timeout for URB submission, since they were using
different values and EHCI's was too short.
Also fixed EHCI to actually check if urb submission succeeded, rather than
silently continuing into the weeds.
Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82
Signed-off-by: Simon Glass <sjg@chromium.org>
Calling eth_bind at usb_eth_init time causes renaming of the network
device from 'usb_ether' to 'usb0'. Fixing this to keep the first name.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Since the ether may not be the only one usb gadget would be used
in the uboot, it is neccessary to do the register each time the
eth begin to work to make usb gadget driver less confussed when
we want to use two different usb gadget at the same time.
Usb gadget driver could simple ignore the register operation, if
it find the driver has been registered already.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Calling usb_dev_init() from within the EHCI host driver is wrong.
The EHCI host driver should have no dependency/interconnection to the
USB device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This patch fixes a problem noticed on lwmon5 (PPC440EPx) using the
common EHCI driver, when "usb reset" is issued multiple times.
Upon the 2nd (and further) "usb reset" command, the command fails
with the following messages:
=> usb reset
(Re)start USB...
USB: Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
scanning bus for storage devices... 2 Storage Device(s) found
=> usb reset
(Re)start USB...
USB: EHCI fail to reset
Error, couldn't init Lowlevel part
This patch fixes this problem. Now "usb reset" can be called multiple
times.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This watchdog reset call is needed here, otherwise the lwmon5 board
(PPC440EPx based) will reset upon the "usb reset" command.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Checking the status field of the qTD token in the current code
do not take into acount cases where endpoint stall (halted) bit
is set together with XactErr status bit. As a result clearing
stall on an endpoint won't be done if this status bit was also
set. Check for halted bit and report USB_ST_STALLED status
if the host controller also indicates endpoit stall condition.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This patch solves a problem with USB hanging under higher load on a
i.MX31 board. It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.
The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.
Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.
Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
