Separate out ata_dev_configure() from ata_dev_identify() such that
ata_dev_configure() only configures @dev according to passed in @id.
The function now does not disable device on failure, it just returns
appropirate error code.
As this change leaves ata_dev_identify() with only reading ID, calling
configure and disabling devices according to the results, this patch
also kills ata_dev_identify() and inlines the logic into
ata_bus_probe().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert dev->id from array to pointer. This is to accomodate
revalidation. During revalidation, both old and new IDENTIFY pages
should be accessible and single ->id array doesn't cut it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kill kfree(id) in failure path of ata_dev_read_id(). id is not
dynamically allocated yet.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_dev_read_id() from ata_dev_identify(). This is the
first half of splitting ata_dev_identify(). ata_dev_read_id() will
also be used for revalidation. This patch does not make any behavior
change.
ata_dev_read_id() doesn't modify any of libata-internal data
structures. It simply reads IDENTIFY page and returns error code on
failure. INIT_DEV_PARAMS and EDD wrong class code are also handled by
this function.
Re-reading IDENTIFY after INIT_DEV_PARAMS is performed by jumping to
retry: instead of calling ata_dev_reread_id(). This is done because
1. there's retry label anyway 2. ata_dev_reread_id() cannot be used
anywhere else so there's no reason to keep it.
This function is probably the place to set transfer mode to PIO0
before IDENTIFY. However, reset -> identify -> init_dev_params order
should be kept for pre-ATA4 devices so we cannot set transfer mode
before IDENTIFY for them. How do we know if a device is post-ATA4
before IDENTIFY?
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes ata_sg_setup_one() trim sg entry (thus making
qc->n_elem zero) if padding results in zero length sg entry.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For ATAPI commands, padding can reduce qc->n_elem by one and thus to
zero making assert(qc->n_elem > 0)'s in ata_fill_sg() and qs_fill_sg()
fail for legal commands. This patch fixes the assert()'s to take
qc->pad_len into account.
Although the condition check seems a bit excessive, as this part of
code isn't still stable yet, I think it's worth to keep those.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The comment above ata_std_postreset() specified that setting cable
type is the responsibility of postreset(), which isn't possible /
optimal depending on controller / driver. This patch kills the
comment. Setting cable type is responsibility of ->probe_reset.
libata doesn't care whether it's done in probeinit, reset or
postreset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update ata_dev_init_params() such that it doesn't disable port
directly but return with appropriate error mask on failure. This is
preparation for splitting ata_dev_identify(). Note that this patch
changes behavior of dev_init_params failure such that only failing
devices are taken offline not the whole port. This change is
intended.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch renames ata_dev_id_[c_]string() to ata_id_[c_]string().
All other functions which read data from ATA ID data start with ata_id
and those two function names were getting too long.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Fix the array index value in ata_rwcmd_protocol() for the added FUA commands.
- Filter out ATAPI packet command error messages in ata_pio_error()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If a low level driver wants to control max_sectors, it had to adjust
ap->host->max_sectors and set ATA_DFLAG_LOCK_SECTORS to tell
ata_scsi_slave_config not to override the limit. This is not only
cumbersome but also incorrect for hosts which support more than one
devices per port.
This patch adds per-device ->max_sectors. If the field is unset
(zero), libata core layer will adjust ->max_sectors according to
default rules. If the field is set, libata honors the setting.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
cdb_len is per-device property. Sharing cdb_len on ap results in
inaccurate configuration on revalidation and hotplugging. This patch
makes cdb_len per-device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ata_dev_knobble() unconditionally used the first device of the port to
determine whether a device is bridged or not. This causes bridge
limit to be incorrectly applied or unapplied for hosts with slave
devices (e.g. ata_piix).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
EDD is never used with ->probe_reset. Don't handle EDD special case
in ata_dev_identify if ->probe_reset is in use.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make ata_dump_id() take @id instead of @dev. This is preparation for
splitting ata_dev_identify().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Separate out ATA major version calculation from ata_dev_identify()
into ata_id_major_version(). It's preparation for splitting
ata_dev_identify().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Separate out n_sectors calculation into ata_id_n_sectors() from
ata_dev_identify(). This will be used by revalidation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ata_dev_id_c_string() reads ATA string from the specified offset of
the given IDENTIFY PAGE and puts it in the specified buffer in trimmed
and NULL-terminated form. The caller must supply a buffer which is
one byte larger than the maximum size of the target ID string.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes ata_bus_probe() normalize classes[] returned by
->probe_reset such that ->probe_reset can return ATA_DEV_UNKNOWN.
This eases implementation of ->probe_reset's which don't directly use
ata_drive_probe_reset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Tejun Heo
Jeff Garzik
Jeff Garzik
Albert Lee