The pktgen_thread.pid is set to current->pid and is never used
after this. So remove this at all.
Found during isolating the explicit pid/tgid usage.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't seem to have any effect on the x86 architecture but it does
have effect on the Axis CRIS architecture.
Signed-off-by: Jesper Bengtsson <jesper.bengtsson@axis.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_CLS_ACT is enabled, tc_classify() is called twice in
prio_classify(). This causes "interesting" behaviour: with the setup
below, packets are duplicated, sent twice to ifb0, and then loop in and
out of ifb0.
The patch uses the previously calculated return value in the switch,
which is probably what Patrick had in mind in commit
bdba91ec70 -- maybe Patrick can
double-check this?
-- example setup --
ifconfig ifb0 up
tc qdisc add dev ifb0 root netem delay 2s
tc qdisc add dev $ETH root handle 1: prio
tc filter add dev $ETH parent 1: protocol ip prio 10 u32 \
match ip dst 172.24.110.6/32 flowid 1:1 \
action mirred egress redirect dev ifb0
ping -c1 172.24.110.6
Signed-off-by: Lucas Nussbaum <lucas.nussbaum@imag.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge code calls ethtool to get speed. The conversion to using
only ethtool_ops broke the case of devices without ethtool_ops.
This is a new regression in 2.6.23.
Rearranged the switch to a logical order, and use gcc initializer.
Ps: speed should have been part of the network device structure from
the start rather than burying it in ethtool.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some packet leakage in bridge. The bridging code was
allowing forward table entries to be generated even if a device was
being blocked. The fix is to not add forwarding database entries
unless the port is active.
The bug arose as part of the conversion to processing STP frames
through normal receive path (in 2.6.17).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cell phone networks do link layer retransmissions and other
things that cause unnecessary timeout retransmits. So allow
the minimum RTO to be inflated per-route to deal with this.
Signed-off-by: David S. Miller <davem@davemloft.net>
If an INIT with invalid parameter length look like this:
Parameter Type : 1
Parameter Length: 800
and not contain any payload, SCTP will ignore this parameter and send
back a INIT-ACK.
This patch is fix to handle this invalid parameter length correctly.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Currently we abort on the INIT chunk we our backlog is currenlty
exceeded. Delay this about untill COOKIE-ECHO to give the user
time to accept the socket. Also, make sure that we treat
sk_max_backlog of 0 as no connections allowed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When performing a retransmit, do not include the chunk if
it was sent less then 1 rtt ago. The reason is that we
may receive the SACK very soon and wouldn't retransmit.
Suggested by Randy Stewart.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Do not set Unconfirmed transports to Inactive state. This may
result in an inactive association being destroyed since we start
counting errors on "inactive" transports against the association.
This was found at the SCTP interop event.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
sctp_bindx() allows the use of unspecified port. The problem is
that every address we bind to ends up selecting a new port if
the user specified port 0. This patch allows re-use of the
already selected port when the port from bindx was 0.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When multi bundling SHUTDOWN-ACK message is received in ESTAB state,
this will cause "sctp protocol violation state" message print many times.
If SHUTDOWN-ACK is bundled 300 times in one packet, message will be
print 300 times. The same problem also exists when received unexpected
HEARTBEAT-ACK message which is bundled message times.
This patch used net_ratelimit() to suppress error messages print too fast.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
PROTOCOL VIOLATION error cause in ABORT is bad encode when make abort
chunk. When SCTP encode ABORT chunk with PROTOCOL VIOLATION error cause,
it just add the error messages to PROTOCOL VIOLATION error cause, the
rest four bytes(struct sctp_paramhdr) is just add to the chunk, not
change the length of error cause. This cause the ABORT chunk to be a bad
format. The chunk is like this:
ABORT chunk
Chunk type: ABORT (6)
Chunk flags: 0x00
Chunk length: 72 (*1)
Protocol violation cause
Cause code: Protocol violation (0x000d)
Cause length: 62 (*2)
Cause information: 5468652063756D756C61746976652074736E2061636B2062...
Cause padding: 0000
[Needless] 00030010
Chunk Length(*1) = 72 but Cause length(*2) only 62, not include the
extend 4 bytes.
((72 - sizeof(chunk_hdr)) = 68) != (62 +3) / 4 * 4
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
At function sctp_addto_chunk(), it do pad before add payload to chunk if
chunk length is not 4-byte alignment. But it do pad with a bad length.
This patch fixed this probleam.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Currently we only assign the sequence number to a packet that
we are about to transmit. This however breaks the Partial
Reliability extensions, because it's possible for us to
never transmit a packet, i.e. it expires before we get to send
it. In such cases, if the message contained multiple SCTP
fragments, and we did manage to send the first part of the
message, the Stream sequence numbers would get into invalid
state and cause receiver to stall.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When we recieve a FWD-TSN (meaning the peer has abandoned the data),
we need to clean up any partially received messages that may be
hanging out on the re-assembly or re-ordering queues. This is
a MUST requirement that was not properly done before.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com.>
Initially pkt_dev can be NULL this causes netif_subqueue_stopped to
oops. The patch below should cure it. But maybe the pktgen TX logic
should be reworked to better support the new multiqueue support.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tried to preserve bridging code as it was before, but logic is quite
strange - I think we should free skb on error, since it is already
unshared and thus will just leak.
Herbert Xu states:
> + if ((skb = skb_share_check(skb, GFP_ATOMIC)) == NULL)
> + goto out;
If this happens it'll be a double-free on skb since we'll
return NF_DROP which makes the caller free it too.
We could return NF_STOLEN to prevent that but I'm not sure
whether that's correct netfilter semantics. Patrick, could
you please make a call on this?
Patrick McHardy states:
NF_STOLEN should work fine here.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a crash that may occur when the routine dev_mc_sync()
deletes an address from the list it is currently going through. It
saves the pointer to the next element before deleting the current one.
The problem may also exist in dev_mc_unsync().
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing n & (n - 1) for power of 2 check by is_power_of_2(n)
Signed-off-by: vignesh babu <vignesh.babu@wipro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People often get tripped up by this function and think that
it does not implemented the prescribed algorithms from
RFC2414 and RFC3390, even though it does.
So add a comment to head off such misunderstandings in the
future.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix IP[V6]_ADD_MEMBERSHIP and IP[V6]_DROP_MEMBERSHIP to
return -EPROTO for connection oriented sockets.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Pavel Emelyanov
Jesper Bengtsson
Lucas Nussbaum
Stephen Hemminger
Wei Yongjun
Vlad Yasevich
Robert Olsson
Evgeniy Polyakov
Benjamin Thery
vignesh babu
Flavio Leitner