ACPICA commit 7d928e3174fb19d7dc0066b03c30bea07c001563
ACPI 6.2 introduced a new resource that is used to declare set of pins
belonging to a GPIO controller. This resource is referenced by new
PinGroupFunction() and PinGroupConfig() resources using ResourceSource
and ResourceLabel fields.
The PinGroup() resource looks like this:
PinGroup (ResourceLabel, ResourceUsage, DescriptorName,
VendorData) {Pin List}
This resource should be listed in _CRS under the GPIO/pincontroller
device providing these pins.
Link: https://github.com/acpica/acpica/commit/7d928e31
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 6bbc6357f7061f1243601adde0ea45f7a89274e0
ACPI 6.2 introduced a new resource that is used to describe how certain
pins are muxed for a device. The ASL syntax of this new resource looks
like below:
PinFunction(Shared, PinConfig, FunctionNumber, ResourceSource,
ResourceSourceIndex, ResourceUsage, DescriptorName,
VendorData) {Pin List}
Which is pretty similar to GpioIo()/GpioInt() resources.
Teach ACPICA about this new resource.
Link: https://github.com/acpica/acpica/commit/6bbc6357
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 3c36625deffdfb034378b1793e2ead9c8fdd767e
Changes the resource descriptor parse tree walk to a general
preprocessing walk and calls the Switch conversion code from here.
Move Switch code to new dmswitch.c file. Also improves algorithm to
handle multiple levels of Switch statements and perform legacy
disassembly for older or otherwise non-spec compliant Switch
implementations.
Link: https://github.com/acpica/acpica/commit/3c36625d
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull key subsystem fixes from James Morris:
"Here are a bunch of fixes for Linux keyrings, including:
- Fix up the refcount handling now that key structs use the
refcount_t type and the refcount_t ops don't allow a 0->1
transition.
- Fix a potential NULL deref after error in x509_cert_parse().
- Don't put data for the crypto algorithms to use on the stack.
- Fix the handling of a null payload being passed to add_key().
- Fix incorrect cleanup an uninitialised key_preparsed_payload in
key_update().
- Explicit sanitisation of potentially secure data before freeing.
- Fixes for the Diffie-Helman code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (23 commits)
KEYS: fix refcount_inc() on zero
KEYS: Convert KEYCTL_DH_COMPUTE to use the crypto KPP API
crypto : asymmetric_keys : verify_pefile:zero memory content before freeing
KEYS: DH: add __user annotations to keyctl_kdf_params
KEYS: DH: ensure the KDF counter is properly aligned
KEYS: DH: don't feed uninitialized "otherinfo" into KDF
KEYS: DH: forbid using digest_null as the KDF hash
KEYS: sanitize key structs before freeing
KEYS: trusted: sanitize all key material
KEYS: encrypted: sanitize all key material
KEYS: user_defined: sanitize key payloads
KEYS: sanitize add_key() and keyctl() key payloads
KEYS: fix freeing uninitialized memory in key_update()
KEYS: fix dereferencing NULL payload with nonzero length
KEYS: encrypted: use constant-time HMAC comparison
KEYS: encrypted: fix race causing incorrect HMAC calculations
KEYS: encrypted: fix buffer overread in valid_master_desc()
KEYS: encrypted: avoid encrypting/decrypting stack buffers
KEYS: put keyring if install_session_keyring_to_cred() fails
KEYS: Delete an error message for a failed memory allocation in get_derived_key()
...
Mika Westerberg
David E. Box
Bob Moore
Lv Zheng
Erik Schmauss
Janosch Hildebrand
Linus Torvalds