After commit 26b88520b8 ("mmc:
omap_hsmmc: remove private DMA API implementation"), the Nokia N800
here stopped booting:
[ 2.086181] Waiting for root device /dev/mmcblk0p1...
[ 2.324066] Unhandled fault: imprecise external abort (0x406) at 0x00000000
[ 2.331451] Internal error: : 406 [#1] ARM
[ 2.335784] Modules linked in:
[ 2.339050] CPU: 0 Not tainted (3.6.0-rc3 #60)
[ 2.344146] PC is at default_idle+0x28/0x30
[ 2.348602] LR is at trace_hardirqs_on_caller+0x15c/0x1b0
...
This turned out to be due to memory corruption caused by long-broken
PIO code in drivers/mmc/host/omap.c. (Previously, this driver had
been using DMA; but the above commit caused the MMC driver to fall
back to PIO mode with an unmodified Kconfig.)
The PIO code, added with the rest of the driver in commit
730c9b7e66 ("[MMC] Add OMAP MMC host
driver"), confused bytes with 16-bit words. This bug caused memory
located after the PIO transfer buffer to be corrupted with transfers
larger than 32 bytes. The driver also did not increment the buffer
pointer after the transfer occurred. This bug resulted in data
corruption during any transfer larger than 64 bytes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The documentation for the dw_mmc part says that the low power
mode should normally only be set for MMC and SD memory and should
be turned off for SDIO cards that need interrupts detected.
The best place I could find to do this is when the SDIO interrupt
was first enabled. I rely on the fact that dw_mci_setup_bus()
will be called when it's time to reenable.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Data transfer will be continued until all the bytes are transmitted,
even if data crc error occurs during a multiple-block data transfer.
This means RXDR/TXDR interrupts will occurs until data transfer is
terminated. Early setting of host->sg to NULL prevents going into
xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts
occurs. And checking error interrupt status in the xxx_data_pio functions
is no need because dw_mci_interrupt does do the same. This patch also
removes it.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Datasheet of SYNOPSYS mentions that DTO(Data Transfer Over) interrupt
will be raised even if some error interrupts, however it is actually
found that DTO does not occur. SYNOPSYS has confirmed this issue.
Current implementation defers the call of tasklet_schedule until DTO
when the error interrupts is happened. This patch fixes error handling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
RINTSTS status includes masked interrupts as well as unmasked.
data_status and cmd_status are set by value of RINTSTS in interrupt handler
and tasklet finally uses it to decide whether error is happened or not.
In addition, MINTSTS status is used for setting data_status in PIO.
Masked error interrupt will not be handled and that status can be considered
non-error case.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed By: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even if the datasheet says that the not busy flag has to be used only
for write operations, it's false except for version lesser than v2xx.
Not waiting on the not busy flag for read operations can cause the
controller to hang-up during the initialization of some SD cards
with DMA after the first CMD6 -- the next command is sent too early.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.5, 3.6]
Signed-off-by: Chris Ball <cjb@laptop.org>
Since commit 30832ab56 ("mmc: sdhci: Always pass clock request value
zero to set_clock host op") was merged, esdhc_set_clock starts hitting
"if (clock == 0)" where ESDHC_SYSTEM_CONTROL has been operated. This
causes SDHCI card-detection function being broken. Fix the regression
by moving "if (clock == 0)" above ESDHC_SYSTEM_CONTROL operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Descriptor array structure has been moved into blackfin dma.h head file.
This patch fix below error:
drivers/mmc/host/bfin_sdh.c:52:8: error: redefinition of 'struct
dma_desc_array'
make[4]: *** [drivers/mmc/host/bfin_sdh.o] Error 1
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
If dma_request_channel() fails (e.g. because DMA enine is not built
into the kernel), the return value from probe is zero causing the
driver to be bound to the device even though probe failed.
To fix, ensure that probe returns an error value when a DMA channel
request fail.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the private DMA API implementation from omap, making it use
entirely the DMA engine API.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add DMA engine support to the OMAP driver. This supplements the
private DMA API implementation contained within this driver, and the
driver can be switched at build time between using DMA engine and the
private DMA API.
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the private DMA API implementation from omap_hsmmc, making it
use entirely the DMA engine API.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add DMA engine support to the OMAP HSMMC driver. This supplements the
private DMA API implementation contained within this driver, and the
driver can be switched at build time between using DMA engine and the
private DMA API.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM SoC fixes from Olof Johansson:
"A mixed bag of fixes, some for merge window fallout (tegra, MXS), and
a short series of fixes for marvell platforms that didn't make it in
before 3.5."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: fix compile error caused by prom_update_property change
ARM: dt: tegra trimslice: enable USB2 port
ARM: dt: tegra trimslice: add vbus-gpio property
ARM: vt8500: Add maintainer for VT8500 architecture
ARM: Kirkwood: Replace mrvl with marvell
ARM: Orion: fix driver probe error handling with respect to clk
ARM: Dove: Fixup ge00 initialisation
ARM: Kirkwood: Fix PHY disable clk problems
ARM: Kirkwood: Ensure runit clock always ticks.
ARM: versatile: Don't use platform clock for Integrator & VE
ARM: tegra: harmony: add regulator supply name and its input supply
The clk patches added code to get and enable clocks in the
respective driver probe functions. If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lumm <andrew@lunn.ch>
Pull slave-dmaengine update from Vinod Koul:
"This time we have a new dmaengine driver from the tegra folks. Also
we have Guennadi's cleanup of sh drivers which incudes a library for
sh drivers. And the usual odd fixes in bunch of drivers and some nice
cleanup of dw_dmac from Andy."
Fix up conflicts in drivers/mmc/host/sh_mmcif.c
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Cleanup logging messages
mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
dma: sh: provide a migration path for slave drivers to stop using .private
dma: sh: use an integer slave ID to improve API compatibility
dmaengine: shdma: prepare to stop using struct dma_chan::private
sh: remove unused DMA device pointer from SIU platform data
ASoC: siu: don't use DMA device for channel filtering
dmaengine: shdma: (cosmetic) simplify a static function
dmaengine: at_hdmac: add a few const qualifiers
dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
dw_dmac: mark dwc_dump_lli inline
dma: mxs-dma: Export missing symbols from mxs-dma.c
dma: shdma: convert to the shdma base library
ASoC: fsi: prepare for conversion to the shdma base library
usb: renesas_usbhs: prepare for conversion to the shdma base library
ASoC: siu: prepare for conversion to the shdma base library
serial: sh-sci: prepare for conversion to the shdma base library
mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
dma: shdma: prepare for conversion to the shdma base library
...
Pull arm-soc clk changes from Arnd Bergmann:
"Clock support is moving to the clk subsystem. These tegra, omap and
imx changes are for code that is still platform specific and not (yet)
part of that subsystem."
Fix up conflicts in arch/arm/mach-{imx/clk-imx51-imx53.c,omap2/Makefile}
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: imx: clk-imx31: Fix clock id for rnga driver
ARM: imx: add missing item to the list of clock event modes
ARM: i.MX5x CSPI: Fixed clock name for CSPI
ARM: i.MX5x clocks: Fix GPT clocks
ARM: i.MX5x clocks: Fix parent for PWM clocks
ARM: i.MX5x clocks: Add EPIT support
ARM: mx27: Reenable silicon version print
ARM: clk-imx27: Fix rtc clock id
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
...
Pull general arm-soc cleanups from Arnd Bergmann:
"These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should not
be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra."
Resolve trivial conflict in arch/arm/mach-omap2/clockdomains3xxx_data.c
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
ARM: S3C24XX: Remove unused GPIO definitions for Openmoko GTA02 board
ARM: S3C24XX: Remove unused GPIO definitions for port J
ARM: S3C24XX: Remove unused GPA, GPE, GPH bank GPIO aliases
ARM: S3C24XX: Convert the touchscreen setup code to common GPIO API
ARM: S3C24XX: Convert the PM code to gpiolib API
ARM: S3C24XX: Convert QT2410 board file to the gpiolib API
ARM: S3C24XX: Convert SMDK board file to the gpiolib API
ARM: S3C24XX: Free the backlight gpio requested in Mini2440 board code
ARM: imx: remove unused pdata from device macros
ARM: imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX_SSI from MACH_MX25_3DS
ARM: at91: fix new build errors
ARM: at91: add AIC5 support
ARM: at91: remove mach/irqs.h
ARM: at91: sparse irq support
ARM: at91: at91 based machines specify their own irq handler at run time
ARM: at91: remove static irq priorities for sam9x5
ARM: at91: add of irq priorities support
...
As mach-dove is moving towards common clock framework prepare
the sdhci driver to grab its clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdio controller on dove doesn't have a bit to indicate
high-speed. With the quirk set it fixes accessing high-speed
sdcards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Paul Walmsley
Ian Chen
Doug Anderson
Seungwon Jeon
Ludovic Desroches
Shawn Guo
Lauri Hintsala
Sonic Zhang
Linus Torvalds
Kevin Hilman
Russell King
Arnd Bergmann
Simon Baatz
Sebastian Hesselbarth