Commit Graph

1136 Commits

Author SHA1 Message Date
Linus Torvalds f27f0a045b Merge master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa
* master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (28 commits)
  [ALSA] Kconfig SND_SEQUENCER_OSS help text fix
  [ALSA] Add Aux input switch control for Aureon Universe
  [ALSA] pcxhr - Fix the crash with REV01 board
  [ALSA] sound/pci/hda: use create_singlethread_workqueue()
  [ALSA] hda-intel - Add support of ATI SB600
  [ALSA] cs4281 - Fix the check of timeout in probe
  [ALSA] cs4281 - Fix the check of right channel
  [ALSA] Test volume resolution of usb audio at initialization
  [ALSA] maestro3.c: fix BUG, optimization
  [ALSA] HDA/Realtek: multiple input mux definitions and pin mode additions
  [ALSA] AdLib FM card driver
  [ALSA] Fix / clean up PCM-OSS setup hooks
  [ALSA] Clean up PCM codes (take 2)
  [ALSA] Tiny clean up of PCM codes
  [ALSA] ISA drivers bailing on first !enable[i]
  [ALSA] Remove obsolete kfree_nocheck call
  [ALSA] Remove obsolete kfree_nocheck call
  [ALSA] Add snd-als300 driver for Avance Logic ALS300/ALS300+ soundcards
  [ALSA] Add snd-riptide driver for Conexant Riptide chip
  [ALSA] hda-codec - Fix noisy output wtih AD1986A 3stack model
  ...
2006-04-02 13:08:49 -07:00
Frederik Deweerdt c2f60c523a [ALSA] Kconfig SND_SEQUENCER_OSS help text fix
Fix misleading help text for SND_SEQUENCER_OSS config option.

Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:01 +02:00
Maximilian Rehkopf af9b70ac00 [ALSA] Add Aux input switch control for Aureon Universe
This patch adds a mixer control which allows the user to switch the Aux
playback between the internal Aux jack, Wavetable, and Rear Line-In on
Aureon Universe cards.

For switching, a PCA9554 (8-line GPIO with I2C interface) and a 74HC4052
(dual 4-way mux/demux) are used.  Output 0 and 1 of the PCA9554 are
connected to the select pins of the 74HC4052. The I2C interface of the
PCA9554 is connected to the card's internal SPI bus which is also used
to control the WM8770 and CS8415. SPI and I2C on the same lines...

To communicate with the PCA9554 the WM8770 and CS8415 are disabled and
an I2C Stop Condition is generated before the Start Condition (needed
for synchronisation because other SPI traffic appear to confuse the
PCA9554). Then a normal I2C data transfer takes place.  Programming must
be done ridiculously slow; in theory, 4.7us is the minimum delay time
for normal-speed I2C according to the datasheet, but even with 10us
switching was unreliable.  The Windows driver from Terratec does the
programming very slowly, too (checked with an oscilloscope).

PCA9554 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/PCA9554_9554A_6.pdf

74HC4052 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/74HC_HCT4052_4.pdf

Signed-off-by: Maximilian Rehkopf <otakon@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:01 +02:00
Markus Bollinger 0bd43b5bc9 [ALSA] pcxhr - Fix the crash with REV01 board
On a new board revision for pcxhr boards, the
PCXHR_CHIPSC_GPI_USERI bit is no more supported.
The cards concerned have a REV01 in their PCI ID.

As the current driver tests this bit and does not load the
first Xilinx binary when it's 1, the card will crash on Xilinx
access over PCI. (the PCI will freeze ....)

The fix (fix to version 1.0.11rc4) works for both REV00 and
REV01 cards.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:01 +02:00
OGAWA Hirofumi ce7415f496 [ALSA] sound/pci/hda: use create_singlethread_workqueue()
process_unsol_events() seems to assume a singlethread one (IOW, racey).
So, this patch uses create_singlethread_workqueue() instead of
create_workqueue().

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:01 +02:00
Felix Kuehling 89be83f8ee [ALSA] hda-intel - Add support of ATI SB600
This patch adds support for high definition audio on ATI SB600.

Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:01 +02:00
Takashi Iwai 38223daa1a [ALSA] cs4281 - Fix the check of timeout in probe
Fix the check of timeout in probe routines to work properly
reagrdless of HZ (ALSA bug#1976).

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:00 +02:00
Takashi Iwai e860f00047 [ALSA] cs4281 - Fix the check of right channel
Fix the check of right channel in mixer volume put callback.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:00 +02:00
Takashi Iwai 14790f1c73 [ALSA] Test volume resolution of usb audio at initialization
Test the volume of usb audio whether actually it works and adjusts
the resolution value according to it.

Some USB audio devices report a lower resolution than it reacts.
The only possible check is to write and read a volume value.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:00 +02:00
Andreas Mohr 0b2dcd5d6a [ALSA] maestro3.c: fix BUG, optimization
- fix brown-paper-bag locking bug (lock() / return / unlock())
- improve central function snd_m3_update_ptr()
  (avoid expensive integer divisions)
- add cpu_relax() to busy-wait I/O loop as recommended
  (does this require special macro support in ALSA for older kernels??)
- constify several structs
- spelling updates

Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:00 +02:00
Jonathan Woithe a1e8d2da03 [ALSA] HDA/Realtek: multiple input mux definitions and pin mode additions
The following patch relative to CVS from 20060324 adds the following
features to the Realtek HDA codec.

1) Define two new pin modes: ALC_PIN_DIR_IN_NOMICBIAS and
   ALC_PIN_DIR_INOUT_NOMICBIAS.  These can be used with jack mode switch
   definitions in mixers to prevent the user being offered the mic bias
   options if the hardware doesn't support it.

2) Add the ability to have different input mux definitions for different
   ADCs.  This is needed because the ALC260 chip uses different mux layouts
   for the two onboard ADCs.  A new field (num_mux_defs) was added to the
   alc_spec and alc_config_preset structures to support this.

3) Adjust numerous comments to make them consistent with the above changes.

4) Utilise the new multi-mux definition functionality for the ALC260 fujitsu
   model to allow recording of the mixer output.

5) Utilise the new multi-mux definition functionality for the ALC260 test
   model to make the mux selections a little less confusing.

6) Allow the headphone jack of the ALC260 acer model to be retasked in
   the mixer.

6) Utilise the new multi-mux definition functionality for the ALC260 acer
   model to give access to the mixer output and the retasked headphone
   jack.

At this stage the *_NOMICBIAS modes are not used.  We have reports that the
"Line" jack of at least some Acer models doesn't pass the bias out, and we
also know that NIDs 0x0f and 0x10 don't seem to accept the mic bias requests
at all.  However, I feel we need to collect more evidence on both counts
before committing to the use of *_NOMICBIAS.  In the case of the Acers, it's
not clear whether this issue (probably caused by the inclusion of DC
blocking capacitors) affects all Acer models or just a small number.  With
the issue with NIDs 0x0f and 0x10 it's unclear whether this is a hardware
bug which will be addressed in later chip revisions or if it's an
intentional restriction.  The datasheet makes no mention of the restriction
so at this stage I'm inclined to consider it a hardware bug.  Comments in
the source reflect this reasoning.

On a similar theme, the headphone jack of the Fujitsu S7020 also doesn't
appear to pass mic bias voltage.  I'm still investigating this however.

With the ability to retask the headphone jack, owners of ALC260-based Acer
laptops should now be able to record 4 channels of audio if they desire. The
multiple mux definitions allow this jack to be presented from both ADCs
(since this mux input is one of those which differs between the muxes).

This patch has been tested on a Fujitsu S7020 laptop and appears to behave
itself both for the "test" and "fujitsu" models.  Definitions using only a
single mux specification also work.  Other ALC chips should be fine but I
cannot test these myself.  The "auto" modes should also continue to function
but again I have not verified this.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:59:00 +02:00
Rene Herman cf40a310a7 [ALSA] AdLib FM card driver
Attached you'll find an ALSA driver for AdLib FM cards. An AdLib card is
just an OPL2, which was already supported by sound/drivers/opl3, so only
very minimal bus-glue is needed. The patch applies cleanly to both
2.6.16 and 2.6.16-mm1.

The driver has been tested with an actual ancient 8-bit ISA AdLib card
and works fine. It also works fine for an OPL3 {,emulation} as still
found on many ISA soundcards but given that AdLib cards don't have their
own mixer, upping the volume from 0 might be a problem without the card
driver already loaded and driving the OPL3.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:59 +02:00
Takashi Iwai 060d77b9c0 [ALSA] Fix / clean up PCM-OSS setup hooks
- Fix possible race of referring the setup hook from the running PCM
- Fix memory leak in an error path of proc write
- Clean up the setup hook parser

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:59 +02:00
Takashi Iwai 3bf75f9b90 [ALSA] Clean up PCM codes (take 2)
- Clean up initialization and destruction of substream instance
  Now snd_pcm_open_substream() alone does most initialization jobs.
  Add pcm_release callback for cleaning up at snd_pcm_release_substream()
- Tidy up PCM oss code

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:59 +02:00
Takashi Iwai bf1bbb5a49 [ALSA] Tiny clean up of PCM codes
- Make snd_pcm_prepare() static
- Clean up snd_pcm_kernel_*_ioctl() functions, reduce exports

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:58 +02:00
Rene Herman 82756b2785 [ALSA] ISA drivers bailing on first !enable[i]
Fix the wrong check of enable option in cmi8330 driver.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:58 +02:00
Takashi Iwai 43560116d1 [ALSA] Remove obsolete kfree_nocheck call
Fixed the compilation, removing obsolete kfree_nocheck() call
for memory debugging.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:58 +02:00
Takashi Iwai 10d150e186 [ALSA] Remove obsolete kfree_nocheck call
Fixed the compilation, removing obsolete kfree_nocheck() call
for memory debugging.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:58 +02:00
Ash Willis b3a70d5ece [ALSA] Add snd-als300 driver for Avance Logic ALS300/ALS300+ soundcards
Added snd-als300 driver for Avance Logic ALS300/ALS300+ soundcards
by Ash Willis.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:58 +02:00
Peter Gruber 109a9638f0 [ALSA] Add snd-riptide driver for Conexant Riptide chip
Add snd-riptide driver for Conexant Riptide chip by Peter Gruber.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:57 +02:00
Takashi Iwai 2125cad291 [ALSA] hda-codec - Fix noisy output wtih AD1986A 3stack model
Fixed the noisy output wtih AD1986A 3stack model using 2 channels.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:57 +02:00
Takashi Iwai 505cb341ef [ALSA] hda-codec - Fix unsol event initialization at resume of stac92xx
Fix the re-initialization of unsolicited events at resume of stac92xx codecs.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:57 +02:00
Takashi Iwai 675b4e5981 [ALSA] Make CONFIG_SND_CS46XX_NEW_DSP yes as default
Removed from CONFIG_EXPERIMENTAL from CONFIG_SND_CS46XX_NEW_DSP, and
make default to yes.  This option works fine for years.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:57 +02:00
Martin Langer 1841f613fd [ALSA] Add snd-miro driver
Added snd-miro driver for miroSOUND PCM by Martin Langer.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:56 +02:00
Takashi Iwai cbac4b0cb6 [ALSA] Cleanup unused argument for snd_power_wait()
Removed the unused file argument of snd_power_wait().

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-31 17:58:56 +02:00