When system enters into kdump kernel because of kernel panic, it won't
shutdown devices. On-flight DMA will continue transferring data until
device driver initializes. All devices are supposed to reset during
driver initialization. And this property is used to fix the kdump
failure in system with intel iommu. Other systems with hardware iommu
should be similar. Please check commit 091d42e ("iommu/vt-d: Copy
translation tables from old kernel") and those commits around.
But bnx2 driver doesn't reset device during driver initialization. The
device resetting is deferred to net device up stage. This will cause
hardware iommu handling failure on bnx2 device. And its resetting relies
on firmware. So in this patch move the firmware requesting code to earlier
bnx2_init_one(), then next call bnx2_reset_chip to reset device.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnx2_init_board, missing free temp_stats_blk on error path when
some operations do failed. Just add the 'kfree' operation.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we have two processes to do:
P1#: ifconfig eth0 down; which will call bnx2_close, then will
, and set Null to stats_blk
P2#: ifconfig eth0; which will call bnx2_get_stats64, it will
use stats_blk.
In one case:
--P1#-- --P2#--
stats_blk(no null)
bnx2_free_mem
->bp->stats_blk = NULL
GET_64BIT_NET_STATS
then it will cause 'NULL Pointer' Problem.
it is as well with 'ethtool -S ethx'.
Allocate the statistics block at probe time so that this problem is
impossible
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag
stripping when the card cannot disable it. The driver should remove
NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed
for the ethtool.
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates BNX2 driver version to 2.2.6 and CNIC driver version
to 2.5.21.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not enable filter SORT MODE in chip init routine. This patch addresses an
issue where BCM5716 sporadically drops packets when changing multicast list.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides additional changes as a part of BNX2 and CNIC driver
re-branding effort.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped. The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
o QLogic has acquired the NetXtremeII products and drivers from Broadcom.
This patch re-brands bnx2 driver as a QLogic driver
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP isn't enabled, bnx2_suspend/resume are unused; don't
build them when they aren't used.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pci shutdown handler added in:
bnx2: Add pci shutdown handler
commit 25bfb1dd4b
created a shutdown down sequence without chip reset if the device was
never brought up. This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive. On some
systems, it may generate NMI in the bnx2's pci shutdown handler.
The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally users want to know what parameters their Broadcom drivers
are running with. For example, a user may want to know if MSI is
disabled.
This patch has been compile tested.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-mdix currently only works if autoneg is enabled. This patch enables
auto-mdix all the time by setting a bit in a PHY register. Define
meaningful constants for this PHY registers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not reset the advertisement register when the speed
is forced, leaving the default advertisement value of 10 Mbps. This does
not work with some link partners when the next patch enables auto-mdix.
Set advertisement register to 0 if the speed is forced.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baoquan He
wangweidong
Ivan Vecera
Rasesh Mody
Jiri Pirko
Vlad Yasevich
Benoit Taine
Jitendra Kalsaria
Daniel J Blueman
David S. Miller
Eric W. Biederman
Michael Chan
Alexander Gordeev
James M Leddy
Paul Gortmaker
Tom Herbert