Setting RF (resume flag) allows a debugger to resume execution after a
code breakpoint without tripping the breakpoint again. It is reset by
the CPU after execution of one instruction.
Requested by Stephane Eranian:
"I am trying to the user HW debug registers on i386 and I am running
into a problem with ptrace() not allowing access to EFLAGS_RF for
POKEUSER (see FLAG_MASK). [ ... ] It avoids the need to remove the
breakpoint, single step, and reinstall. The equivalent functionality
exists on IA-64 and is allowed by ptrace()"
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to the manual, INT 6 is "invalid opcode", not "invalid operand".
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now needs to include the type 1 functions ("direct") too.
Reported by Pavel Roskin <proski@gnu.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use correct address when referencing mmconfig aperture while checking
for broken MCFG. This was a typo when porting the code from 64bit to
32bit. It caused oopses at boot on some ThinkPads.
Should definitely go into 2.6.15.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They report all busses as MMCONFIG capable, but it never works for the
internal devices in the CPU's builtin northbridge.
It just probes all func 0 devices on bus 0 (the internal northbridge is
currently always on bus 0) and if they are not accessible using MCFG they are
put into a special fallback bitmap.
On systems where it isn't we assume the BIOS vendor supplied correct MCFG.
Requires the earlier patch for mmconfig type1 fallback
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When there is no entry for a bus in MCFG fall back to type1. This is
especially important on K8 systems where always some devices can't be accessed
using mmconfig (in particular the builtin northbridge doesn't support it for
its own devices)
Cc: <gregkh@suse.de>
Cc: <jgarzik@pobox.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's illegal because it can sleep.
Use a two step lookup scheme instead. First look up the vm_struct, then
change the direct mapping, then finally unmap it. That's ok because nobody
can change the particular virtual address range as long as the vm_struct is
still in the global list.
Also added some LinuxDoc documentation to iounmap.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disabling LAPIC timer isn't sufficient. In some situations, such as we
enabled NMI watchdog, there is still unexpected interrupt (such as NMI)
invoked in offline CPU. This also avoids offline CPU receives spurious
interrupt and anything similar.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CPU hotplug enabled, NMI watchdog stoped working. It appears the
violation is the cpu_online check in nmi handler. local ACPI based NMI
watchdog is initialized before we set CPU online for APs. It's quite
possible a NMI is fired before we set CPU online, and that's what happens
here.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
What is the value shown in "cpu MHz" of /proc/cpuinfo when CPUs are capable of
changing frequency?
Today the answer is: It depends.
On i386:
SMP kernel - It is always the boot frequency
UP kernel - Scales with the frequency change and shows that was last set.
On x86_64:
There is one single variable cpu_khz that gets written by all the CPUs. So,
the frequency set by last CPU will be seen on /proc/cpuinfo of all the
CPUs in the system. What you see also depends on whether you have constant_tsc
capable CPU or not.
On ia64:
It is always boot time frequency of a particular CPU that gets displayed.
The patch below changes this to:
Show the last known frequency of the particular CPU, when cpufreq is present. If
cpu doesnot support changing of frequency through cpufreq, then boot frequency
will be shown. The patch affects i386, x86_64 and ia64 architectures.
Signed-off-by: Venkatesh Pallipadi<venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch moves away PMBASE reading and only performs it at
cpufreq_register_driver time by exiting with -ENODEV if unable to read
the value.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
The attached patch introduces runtime latency measurement for ICH[234]
based chipsets instead of using CPUFREQ_ETERNAL. It includes
some sanity checks in case the measured value is out of range and
assigns a safe value of 500uSec that should still be enough on
problematics chipsets (current testing report values ~200uSec). The
measurement is currently done in speedstep_get_freqs in order to avoid
further unnecessary transitions and in the hope it'll come handy for SMI
also.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
speedstep-ich.c | 4 ++--
speedstep-lib.c | 32 +++++++++++++++++++++++++++++++-
speedstep-lib.h | 1 +
speedstep-smi.c | 1 +
4 files changed, 35 insertions(+), 3 deletions(-)
If a user has booted with 'quiet', some important messages don't
get displayed which really should. We've seen at least one case
where powernow-k8 stopped working, and the user needed a BIOS update
that they didn't know about.
Signed-off-by: Dave Jones <davej@redhat.com>
Thanks to LinuxICC (http://linuxicc.sf.net), a comparison of a u32 less
than 0 was found, this patch changes the variable to a signed int so that
comparison is meaningful.
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Setting irq affinity stops working when MSI is enabled. With MSI, move_irq
is empty, so we can't change irq affinity. It appears a typo in Ashok's
original commit for this issue. X86_64 actually is using move_native_irq.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chuck Ebbert
Linus Torvalds
Stas Sergeev
Andi Kleen
Al Viro
Shaohua Li
Keshavamurthy Anil S
Venkatesh Pallipadi
Mattia Dongili
Dave Jones
Gabriel A. Devenyi
Thierry Vignaud