SFF incorrectly assumed that ctl register is available for all
controllers while some old SFF controllers don't have ctl register.
Make SFF handle controllers w/o ctl register by conditionalizing ctl
register access and softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some old SFF controllers don't have any way to reset the channel.
Currently, this isn't supported and libata EH causes an oops. Allow
LLDs w/o any reset method and just assume ATA class in such cases.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds another Broadcom BCM2045 based device to the blacklist, with
these settings the micro dongle works on my system.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ide_tune_dma() should return '1' if IDE_HFLAG_NO_SET_MODE host flag is set.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Thursday 06 March 2008, walt wrote:
> For me, this commit causes the problem it's intended to fix:
>
> commit 9f10d9ee0a
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Tue Feb 26 21:50:35 2008 +0100
>
> ide-cd: fix 'ireason' handling for REQ_TYPE_ATA_PC requests
>
> This fixes some hangs caused by not finishing the transfer before ending
> the request and also makes use of 'ireason == 1' quirk for spurious IRQs.
>
> When I mount a CD there is a long delay, and I see this error message:
>
> hdc: ide_cd_check_ireason: wrong transfer direction!
> cdrom: failed setting lba address space
> hdc: status error: status=0x58 { DriveReady SeekComplete DataRequest }
> ide: failed opcode was: unknown
> hdc: drive not ready for command
> <repeated many times>
>
> When I revert this commit everything works properly again, including
> CD burning.
It turned out that REQ_TYPE_ATA_PC write requests were not marked as such
(the previous commit assumed them to be).
Reported-by: walt <w41ter@gmail.com>
Tested-by: walt <w41ter@gmail.com>
Reviewed-by: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The card state mutex was only initialized when a device was connected,
but used during unload unconditionally, leading to an Oops if a driver
was loaded and unloaded again without ever connecting a device.
Fix this by initializing the mutex as soon as the structure is allocated.
Also add a missing mutex unlock revealed in the same execution path.
This fixes a possible Oops in 2.6.25-rc that was introduced by commit
e468c04894 ("Gigaset: permit module
unload").
Thanks to Roland Kletzing for reporting this problem.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Tested-by: Roland Kletzing <devzero@web.de>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
randconfig testing found a bootup lockup in drivers/char/esp.c because
of a spinlock that wasn't correctly initialized.
I'm not sure why it became more prominent in 2.6.25-rc4, the bug seems
rather old and i've been doing allyesconfig bootups for ages with
CONFIG_ESP enabled.
This fixes this bootup lockup:
PM: Adding info for No Bus:ttyP63
ttyP32 at 0x0240 (irq = 0) is an ESP primary port
BUG: spinlock lockup on CPU#0, swapper/1, f56dd004
Pid: 1, comm: swapper Not tainted 2.6.25-rc4-sched-devel.git-x86-latest.git #402 [<c03ac6f4>] _raw_spin_lock+0x134/0x140
[<c08649be>] _spin_lock_irqsave+0x5e/0x80
[<c0b9fbfe>] ? espserial_init+0x2be/0x6e0
[<c0b9fbfe>] espserial_init+0x2be/0x6e0
[<c0b877a3>] kernel_init+0x83/0x260
[<c0b9f940>] ? espserial_init+0x0/0x6e0
[<c010416a>] ? restore_nocheck_notrace+0x0/0xe
[<c0b87720>] ? kernel_init+0x0/0x260
[<c0b87720>] ? kernel_init+0x0/0x260
[<c0104507>] kernel_thread_helper+0x7/0x10
=======================
kzalloc() is not the way to initialize spinlocks anymore.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hitfb presently has probe using __init whilst remove uses __devexit.
As this device can't possibly be hotplugged, switch to __exit and
__exit_p() instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Building with CONFIG_DEBUG_SECTION_MISMATCH=y reports:
CC drivers/video/pvr2fb.o
LD drivers/video/built-in.o
WARNING: drivers/video/built-in.o(.text+0xb9b0): Section mismatch in reference from the function pvr2fb_check_var() to the variable .devinit.data:pvr2_fix
The function pvr2fb_check_var() references
the variable __devinitdata pvr2_fix.
This is often because pvr2fb_check_var lacks a __devinitdata
annotation or the annotation of pvr2_fix is wrong.
This is obviously crap as no such reference exists, but it's a bit
closer to reality from older versions which blamed the PCI table. The
real problem was a reference to pvr2_var.vmode from pvr2fb_check_var(),
as pvr2_var is flagged as __devinitdata (pvr2_fix is also, so at least
that part is right).
pvr2_var.vmode is just a fancy way of saying FB_VMODE_NONINTERLACED, so
we just reference that explicitly instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the following warnings:
WARNING: vmlinux.o(.text+0xfe6711): Section mismatch in reference from the function cpufreq_unregister_driver() to the variable .cpuinit.data:cpufreq_cpu_notifier
WARNING: vmlinux.o(.text+0xfe68af): Section mismatch in reference from the function cpufreq_register_driver() to the variable .cpuinit.data:cpufreq_cpu_notifier
WARNING: vmlinux.o(.exit.text+0xc4fa): Section mismatch in reference from the function cpufreq_stats_exit() to the variable .cpuinit.data:cpufreq_stat_cpu_notifier
The warnings were casued by references to unregister_hotcpu_notifier()
from normal functions or exit functions.
This is flagged by modpost as a potential error because
it does not know that for the non HOTPLUG_CPU
scenario the unregister_hotcpu_notifier() is a nop.
Silence the warning by replacing the __initdata
annotation with a __refdata annotation.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
For qla4xxx, we could be starting a session, but some error (network,
target, IO from a device that got started, etc) could cause the session
to fail and curring the block/unblock and state manipulation could race
with each other. This patch just has those operations done in the
single threaded iscsi eh work queue, so that way they are serialized.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We are seeing EXIST errors from sysfs during device addition.
We need a start scan callout so we do not start scanning sessions
found during hba setup, before the async scsi scan code is ready.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The host reset callout could be starting to reset the hba at the same
time the dpc thread is. This creates lots of problems because they both
want to do wierd things with the firmware and interrupts, etc.
This patch just has the host reset function fully shutdown the dpc
thread before resetting the hba.
This patch also moves the setting of the session online bit to fix
a potential race with the dpc thread and iscsi recovery thread.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tejun Heo
Harvey Harrison
Karsten Keil
Randy Dunlap
Peter Teoh
Bartlomiej Zolnierkiewicz
Tilman Schmidt
Ingo Molnar
Linus Torvalds
Paul Mundt
FUJITA Tomonori
Krzysztof Oledzki
Sam Ravnborg
Dave Jones
Mike Christie